AL Ho72 - The 1947 - Present Chevrolet & GMC Truck Message Board Network

**mongocanfly** · 08-26-2021, 02:08 PM

Is there any value to a 67 or 69 3/4 ton axle parts..I believe HO72..correct t me if I'm wrong..
The rear brake drums were bought new in the 80s from a Chevy dealership.. installed,, then sat in the barn ever since...they are rusted and would need turned, but have less than 1 mile on them..the brakes were never hooked up ..I pulled the diff cover and it's a open diff with I believe 4.57 gears...32 teeth on the ring gear...axles appear good as well...
Before I haul it off for scrap I thought I'd see if theres any interest
Also have the closed knuckle front from the same truck,, but it's still under a truck...
I'm sure shipping any of this heavy stuff may not make it worthwhile..

**Louisvillekytruck** · 08-26-2021, 02:39 PM

Do u have the ubolts and the lower and upper plates for it

**mongocanfly** · 08-26-2021, 02:43 PM

No, sorry...the u bolts left on the last load of scrap..the plates were used on another truck
A while back I was informed to never reuse the u bolts....although we've reused them for yrs

**Louisvillekytruck** · 08-26-2021, 02:47 PM

Greg pm you

08-26-2021, 02:08 PM	#1
mongocanfly Post Whore Join Date: May 2015 Location: Alabama Posts: 14,670	Ho72 Is there any value to a 67 or 69 3/4 ton axle parts..I believe HO72..correct t me if I'm wrong.. The rear brake drums were bought new in the 80s from a Chevy dealership.. installed,, then sat in the barn ever since...they are rusted and would need turned, but have less than 1 mile on them..the brakes were never hooked up ..I pulled the diff cover and it's a open diff with I believe 4.57 gears...32 teeth on the ring gear...axles appear good as well... Before I haul it off for scrap I thought I'd see if theres any interest Also have the closed knuckle front from the same truck,, but it's still under a truck... I'm sure shipping any of this heavy stuff may not make it worthwhile.. Attached Images __________________ Mongo...aka Greg RIP Dad RIP Jesse 1981 C30 LQ9 NV4500..http://67-72chevytrucks.com/vboard/s...d.php?t=753598 Mongos AD- LS3 TR6060...http://67-72chevytrucks.com/vboard/s...34#post8522334 Columbus..the 1957 IH 4x4...http://67-72chevytrucks.com/vboard/s...63#post8082563 2023 Chevy Z71..daily driver Last edited by mongocanfly; 08-26-2021 at 02:42 PM.

08-26-2021, 02:39 PM	#2
Louisvillekytruck Senior Member Join Date: Jun 2019 Location: Louisville ky Posts: 1,109	Re: Ho72 Do u have the ubolts and the lower and upper plates for it

08-26-2021, 02:43 PM	#3
mongocanfly Post Whore Join Date: May 2015 Location: Alabama Posts: 14,670	Re: Ho72 No, sorry...the u bolts left on the last load of scrap..the plates were used on another truck A while back I was informed to never reuse the u bolts....although we've reused them for yrs __________________ Mongo...aka Greg RIP Dad RIP Jesse 1981 C30 LQ9 NV4500..http://67-72chevytrucks.com/vboard/s...d.php?t=753598 Mongos AD- LS3 TR6060...http://67-72chevytrucks.com/vboard/s...34#post8522334 Columbus..the 1957 IH 4x4...http://67-72chevytrucks.com/vboard/s...63#post8082563 2023 Chevy Z71..daily driver

08-26-2021, 02:47 PM	#4
Louisvillekytruck Senior Member Join Date: Jun 2019 Location: Louisville ky Posts: 1,109	Re: Ho72 Greg pm you

Thread Tools
Show Printable Version Email this Page
Display Modes
Linear Mode Switch to Hybrid Mode Switch to Threaded Mode



Register or Log In To remove these advertisements.

Register or Log In To remove these advertisements.