My 1968 C-20 Golden Anniversary Project - Page 8 - The 1947 - Present Chevrolet & GMC Truck Message Board Network

GerhardH · 10-18-2020, 09:40 AM

THANKS DALE!

Found out that the NOS flame arrestor #3857476 is wrong- too big, see picture. Fortunatly I have a complete set from our fellow ROOGER KOOP here in the forum.

GerhardH · 10-18-2020, 10:01 AM

FOUND THE RIGHT FITTINGS FORE THE OIL PRESSURE GAUGE AND VACUUM GAUGE INSTALLATION.

NAPA 302X2, 6200X2, 6100X2
LMC truck 36-1923 Oil Pressure Tube Kit-49", 31-3406 Vacuum fitting-Tee-Barbed,31-3404 Barbed Fitting-Gauge

Bolts Air intake Manifold: ARP 134-2001

GerhardH · 10-18-2020, 10:18 AM

Preparing Water outlet, found out that my manifold despite the same casting number as the original has not the hole for cooling water (connection to pump), therefore I try the riser (thermostat above the opening for the hole)

GerhardH · 10-18-2020, 10:23 AM

Some more pictures:

Gasket FEL-2202
Vintage Air water Neck Riser VTA-706001-VCQ
Water outlet four seasons 84820
Thermostat: Mr Gasket #4365 195° Fahrenheit (90.5° C)

GerhardH · 10-18-2020, 10:30 AM

Further manifold accessories:
Vacuum fitting (for power brake, heating/air condition reservoir & transmission TH400, spigott must be inside the fitting.

Distributor fittings

GerhardH · 10-18-2020, 10:39 AM

Rockerarm Kit SUM -G6800 1.5 Ratio, Fits 3/8" studs

Hydraulic lifter Federal Mogul HT-817

Engine Mount screws totally stainless 6-2259

GerhardH · 10-18-2020, 10:51 AM

Temperature sending unit: 01513321

Preparing exhaust manifolds #3896956 #3855163

Exhaust Manifold LH (Driver): 3855163 L.H (Cast 8155163A or 3855163A), interchangeable 387241
Exhaust Manifold RH (Passenger): 3896956 R.H. (discontinued use 3905364 or 3932469)

Preparing some measurements camshaft degreeing

GerhardH · 10-18-2020, 10:56 AM

Oil dip stick Kit PRO-66116

Some pictures regarding exhaust gas mainifold heat shields

cornerstone · 10-23-2020, 08:18 PM

Amazing work Gerhard! You're going to have the nicest C10 in all of Germany

GerhardH · 08-09-2021, 10:08 AM

Last entry from 10-18-2020, 04:56 PM , was completly frustrated, because of the not matching valve timings (tested with Summit Degree Wheel), after studing and learning alot now new hope, start soon.

**Ol Blue K20** · 08-10-2021, 06:45 AM

Goodness, you're getting technical. I'm glad to see you're still around....

GerhardH · 05-26-2022, 04:24 AM

Hobby is gone, truck sold, was a nice time here in the forum

**68bowtie** · 05-26-2022, 07:13 PM

Noooo! Say it isn’t so. Call it temporary, leave the door open just in case another truck happens to cross your path.

LT7A · 05-28-2022, 05:52 AM

Oh man, hadn't seen this build before, was just getting into it. I've never seen such detailed care taken in engine assembly. Good luck Gerhard. Sorry to hear that you sold it, but sometimes that has to happen. Hope to see you back. It looks like you got it all together. How did it run?

**Ol Blue K20** · 05-30-2022, 06:58 AM

You can still stop in Gerhard.

cornerstone · 05-31-2022, 05:00 PM

I'm surprised! What's the next project Gerhard?

JerDom · 09-22-2023, 12:18 PM

Quote:

Originally Posted by Ol Blue K20

Goodness, you're getting technical. I'm glad to see you're still around....

Quote:

Originally Posted by GerhardH

Hobby is gone, truck sold, was a nice time here in the forum

I JUST came across this thread.

I knew this was going to happen

I gave, made, sold many parts to Gerhard and tried to give him a lot of common sense advice but being a German engineer he was determined to complicate the living dung out of everything.

I always wondered if he'd frustrate himself into packing it in which looks like finally happened - so sorry , too bad

Jerry in Canada

10-18-2020, 09:40 AM	#176
GerhardH Registered User Join Date: Aug 2017 Location: South Germany Posts: 527	Re: My 1968 C-20 Golden Anniversary Project THANKS DALE! Found out that the NOS flame arrestor #3857476 is wrong- too big, see picture. Fortunatly I have a complete set from our fellow ROOGER KOOP here in the forum. Attached Images __________________ Best regards GerhardH! Members met: 68 short step, 68bowtie, 72c20customcamper, botmfedr1, C/10 King, Chevyland, cornerstore, dmjlambert, fun in dirt, GMan69, Ol Blue K20 1968 CHEVROLET C20 Custom Camper 50th Anniversary, Long bed (LB) 8', 327 V8, Air Condition (AC), Power Steering (PS), Power Brake (PB), Z62 Custom & Comfort Appearance, Turbo Hydramatic TH 400 http://67-72chevytrucks.com/vboard/s...d.php?t=760400 Last edited by GerhardH; 10-18-2020 at 09:46 AM.

10-18-2020, 10:01 AM	#177
GerhardH Registered User Join Date: Aug 2017 Location: South Germany Posts: 527	Re: My 1968 C-20 Golden Anniversary Project FOUND THE RIGHT FITTINGS FORE THE OIL PRESSURE GAUGE AND VACUUM GAUGE INSTALLATION. NAPA 302X2, 6200X2, 6100X2 LMC truck 36-1923 Oil Pressure Tube Kit-49", 31-3406 Vacuum fitting-Tee-Barbed,31-3404 Barbed Fitting-Gauge Bolts Air intake Manifold: ARP 134-2001 Attached Images __________________ Best regards GerhardH! Members met: 68 short step, 68bowtie, 72c20customcamper, botmfedr1, C/10 King, Chevyland, cornerstore, dmjlambert, fun in dirt, GMan69, Ol Blue K20 1968 CHEVROLET C20 Custom Camper 50th Anniversary, Long bed (LB) 8', 327 V8, Air Condition (AC), Power Steering (PS), Power Brake (PB), Z62 Custom & Comfort Appearance, Turbo Hydramatic TH 400 http://67-72chevytrucks.com/vboard/s...d.php?t=760400

10-18-2020, 10:18 AM	#178
GerhardH Registered User Join Date: Aug 2017 Location: South Germany Posts: 527	Re: My 1968 C-20 Golden Anniversary Project Preparing Water outlet, found out that my manifold despite the same casting number as the original has not the hole for cooling water (connection to pump), therefore I try the riser (thermostat above the opening for the hole) Attached Images __________________ Best regards GerhardH! Members met: 68 short step, 68bowtie, 72c20customcamper, botmfedr1, C/10 King, Chevyland, cornerstore, dmjlambert, fun in dirt, GMan69, Ol Blue K20 1968 CHEVROLET C20 Custom Camper 50th Anniversary, Long bed (LB) 8', 327 V8, Air Condition (AC), Power Steering (PS), Power Brake (PB), Z62 Custom & Comfort Appearance, Turbo Hydramatic TH 400 http://67-72chevytrucks.com/vboard/s...d.php?t=760400 Last edited by GerhardH; 10-18-2020 at 01:44 PM.

10-18-2020, 10:23 AM	#179
GerhardH Registered User Join Date: Aug 2017 Location: South Germany Posts: 527	Re: My 1968 C-20 Golden Anniversary Project Some more pictures: Gasket FEL-2202 Vintage Air water Neck Riser VTA-706001-VCQ Water outlet four seasons 84820 Thermostat: Mr Gasket #4365 195° Fahrenheit (90.5° C) Attached Images __________________ Best regards GerhardH! Members met: 68 short step, 68bowtie, 72c20customcamper, botmfedr1, C/10 King, Chevyland, cornerstore, dmjlambert, fun in dirt, GMan69, Ol Blue K20 1968 CHEVROLET C20 Custom Camper 50th Anniversary, Long bed (LB) 8', 327 V8, Air Condition (AC), Power Steering (PS), Power Brake (PB), Z62 Custom & Comfort Appearance, Turbo Hydramatic TH 400 http://67-72chevytrucks.com/vboard/s...d.php?t=760400

10-18-2020, 10:30 AM	#180
GerhardH Registered User Join Date: Aug 2017 Location: South Germany Posts: 527	Re: My 1968 C-20 Golden Anniversary Project Further manifold accessories: Vacuum fitting (for power brake, heating/air condition reservoir & transmission TH400, spigott must be inside the fitting. Distributor fittings Attached Images __________________ Best regards GerhardH! Members met: 68 short step, 68bowtie, 72c20customcamper, botmfedr1, C/10 King, Chevyland, cornerstore, dmjlambert, fun in dirt, GMan69, Ol Blue K20 1968 CHEVROLET C20 Custom Camper 50th Anniversary, Long bed (LB) 8', 327 V8, Air Condition (AC), Power Steering (PS), Power Brake (PB), Z62 Custom & Comfort Appearance, Turbo Hydramatic TH 400 http://67-72chevytrucks.com/vboard/s...d.php?t=760400

10-18-2020, 10:39 AM	#181
GerhardH Registered User Join Date: Aug 2017 Location: South Germany Posts: 527	Re: My 1968 C-20 Golden Anniversary Project Rockerarm Kit SUM -G6800 1.5 Ratio, Fits 3/8" studs Hydraulic lifter Federal Mogul HT-817 Engine Mount screws totally stainless 6-2259 Attached Images __________________ Best regards GerhardH! Members met: 68 short step, 68bowtie, 72c20customcamper, botmfedr1, C/10 King, Chevyland, cornerstore, dmjlambert, fun in dirt, GMan69, Ol Blue K20 1968 CHEVROLET C20 Custom Camper 50th Anniversary, Long bed (LB) 8', 327 V8, Air Condition (AC), Power Steering (PS), Power Brake (PB), Z62 Custom & Comfort Appearance, Turbo Hydramatic TH 400 http://67-72chevytrucks.com/vboard/s...d.php?t=760400

10-18-2020, 10:51 AM	#182
GerhardH Registered User Join Date: Aug 2017 Location: South Germany Posts: 527	Re: My 1968 C-20 Golden Anniversary Project Temperature sending unit: 01513321 Preparing exhaust manifolds #3896956 #3855163 Exhaust Manifold LH (Driver): 3855163 L.H (Cast 8155163A or 3855163A), interchangeable 387241 Exhaust Manifold RH (Passenger): 3896956 R.H. (discontinued use 3905364 or 3932469) Preparing some measurements camshaft degreeing Attached Images __________________ Best regards GerhardH! Members met: 68 short step, 68bowtie, 72c20customcamper, botmfedr1, C/10 King, Chevyland, cornerstore, dmjlambert, fun in dirt, GMan69, Ol Blue K20 1968 CHEVROLET C20 Custom Camper 50th Anniversary, Long bed (LB) 8', 327 V8, Air Condition (AC), Power Steering (PS), Power Brake (PB), Z62 Custom & Comfort Appearance, Turbo Hydramatic TH 400 http://67-72chevytrucks.com/vboard/s...d.php?t=760400

10-18-2020, 10:56 AM	#183
GerhardH Registered User Join Date: Aug 2017 Location: South Germany Posts: 527	Re: My 1968 C-20 Golden Anniversary Project Oil dip stick Kit PRO-66116 Some pictures regarding exhaust gas mainifold heat shields Attached Images __________________ Best regards GerhardH! Members met: 68 short step, 68bowtie, 72c20customcamper, botmfedr1, C/10 King, Chevyland, cornerstore, dmjlambert, fun in dirt, GMan69, Ol Blue K20 1968 CHEVROLET C20 Custom Camper 50th Anniversary, Long bed (LB) 8', 327 V8, Air Condition (AC), Power Steering (PS), Power Brake (PB), Z62 Custom & Comfort Appearance, Turbo Hydramatic TH 400 http://67-72chevytrucks.com/vboard/s...d.php?t=760400 Last edited by GerhardH; 10-18-2020 at 11:07 AM.

10-23-2020, 08:18 PM	#184
cornerstone Registered User Join Date: Apr 2014 Location: Azle,Texas Posts: 2,248	Re: My 1968 C-20 Golden Anniversary Project Amazing work Gerhard! You're going to have the nicest C10 in all of Germany __________________ Brian 1972 C10, "Loyd", LWB to SWB, 5.3, L83/6L80e, 4:11 Tru Trac, Air Ride, VA, DD, 20" Coys, 4 wheel disc, A quick LS swap turned into a 6 year frame off resto-mod.

08-09-2021, 10:08 AM	#185
GerhardH Registered User Join Date: Aug 2017 Location: South Germany Posts: 527	Re: My 1968 C-20 Golden Anniversary Project Last entry from 10-18-2020, 04:56 PM , was completly frustrated, because of the not matching valve timings (tested with Summit Degree Wheel), after studing and learning alot now new hope, start soon. Attached Images __________________ Best regards GerhardH! Members met: 68 short step, 68bowtie, 72c20customcamper, botmfedr1, C/10 King, Chevyland, cornerstore, dmjlambert, fun in dirt, GMan69, Ol Blue K20 1968 CHEVROLET C20 Custom Camper 50th Anniversary, Long bed (LB) 8', 327 V8, Air Condition (AC), Power Steering (PS), Power Brake (PB), Z62 Custom & Comfort Appearance, Turbo Hydramatic TH 400 http://67-72chevytrucks.com/vboard/s...d.php?t=760400

08-10-2021, 06:45 AM	#186
Ol Blue K20 Proprietor of Dale's Corner Join Date: Nov 2012 Location: Vacaville , CA Posts: 16,245	Re: My 1968 C-20 Golden Anniversary Project Goodness, you're getting technical. I'm glad to see you're still around.... __________________ "Some Days Chickens And Some Days Feathers" Dale XNGH ECV Sam Brannan 1004 R.I.P. 67ChevyRedneck R.I.P. Grumpy Old Man R.I.P. FleetsidePaul

05-26-2022, 04:24 AM	#187
GerhardH Registered User Join Date: Aug 2017 Location: South Germany Posts: 527	Re: My 1968 C-20 Golden Anniversary Project Hobby is gone, truck sold, was a nice time here in the forum Attached Images __________________ Best regards GerhardH! Members met: 68 short step, 68bowtie, 72c20customcamper, botmfedr1, C/10 King, Chevyland, cornerstore, dmjlambert, fun in dirt, GMan69, Ol Blue K20 1968 CHEVROLET C20 Custom Camper 50th Anniversary, Long bed (LB) 8', 327 V8, Air Condition (AC), Power Steering (PS), Power Brake (PB), Z62 Custom & Comfort Appearance, Turbo Hydramatic TH 400 http://67-72chevytrucks.com/vboard/s...d.php?t=760400

05-26-2022, 07:13 PM	#188
68bowtie Senior Member Join Date: Jan 2007 Location: Turlock, CA Posts: 8,795	Re: My 1968 C-20 Golden Anniversary Project Noooo! Say it isn’t so. Call it temporary, leave the door open just in case another truck happens to cross your path. __________________ Please help my sister in law with her battle with cancer https://gofund.me/902f6fce Project "C10 Fever" (68 factory black 396 swb) Project "Little Sister" (70 c10 blue original paint refresh) Project "Blue Bomb" (70 c30 blue original paint refresh) SOLD Project "Vitamin C" (71 c10 orange original paint refresh) SOLD

05-28-2022, 05:52 AM	#189
LT7A Registered User Join Date: Oct 2015 Location: PNW Posts: 3,619	Re: My 1968 C-20 Golden Anniversary Project Oh man, hadn't seen this build before, was just getting into it. I've never seen such detailed care taken in engine assembly. Good luck Gerhard. Sorry to hear that you sold it, but sometimes that has to happen. Hope to see you back. It looks like you got it all together. How did it run?

05-30-2022, 06:58 AM	#190
Ol Blue K20 Proprietor of Dale's Corner Join Date: Nov 2012 Location: Vacaville , CA Posts: 16,245	Re: My 1968 C-20 Golden Anniversary Project You can still stop in Gerhard. __________________ "Some Days Chickens And Some Days Feathers" Dale XNGH ECV Sam Brannan 1004 R.I.P. 67ChevyRedneck R.I.P. Grumpy Old Man R.I.P. FleetsidePaul



Register or Log In To remove these advertisements.

05-31-2022, 05:00 PM	#191
cornerstone Registered User Join Date: Apr 2014 Location: Azle,Texas Posts: 2,248	Re: My 1968 C-20 Golden Anniversary Project I'm surprised! What's the next project Gerhard? __________________ Brian 1972 C10, "Loyd", LWB to SWB, 5.3, L83/6L80e, 4:11 Tru Trac, Air Ride, VA, DD, 20" Coys, 4 wheel disc, A quick LS swap turned into a 6 year frame off resto-mod.

Thread Tools
Show Printable Version Email this Page
Display Modes
Linear Mode Switch to Hybrid Mode Switch to Threaded Mode

Register or Log In To remove these advertisements.