Need pics. of transfer case mounts and bushings - The 1947 - Present Chevrolet & GMC Truck Message Board Network

tractorsx · 08-03-2007, 05:42 PM

I pulled out trans. and transfer case a couple of month ago, I took pics but
didn't get right detail. Now I'm trying to put it back in and can't figure out
how the transfer case mount and bushings fit to the frame, nothing is lining up for me at this time? It in a 71 chevy 3/4 ton 4X4. Manual four speed trans. Thanks

msgross · 08-03-2007, 08:01 PM

check out my build thread, should be the same... I can assist with any "detailed" pics that you need.

eedgell · 08-03-2007, 08:11 PM

http://67-72chevytrucks.com/vboard/a...1&d=1186186077

Does this help? NP 205-4 speed, 1971

tractorsx · 08-04-2007, 09:40 AM

Thanks for the pics both of you guys, I looked at all of them, a couple of them were very close but I could'nt make out what I needed. I'll go outside in a short while and take pics of what I am looking for and what my problem is? I haven't posted pics on this board before, but I'll try. What I'm looking for is the placement of the bushings, and which half is top and bottom, there is a large and small half each?

eedgell · 08-04-2007, 11:22 AM

http://67-72chevytrucks.com/vboard/a...1&d=1186240631

The thicker bushings go between the lower frame rail lip, and the large bracket. The thinner bushings go between the larger and smaller bracket. The smaller bracket is bolted to the center of the frame, and the large bracket from the lower frame lip to the side of the T-case. Hope this helps.

tractorsx · 08-04-2007, 04:08 PM

Thanks a million times for the pics eedgell!!! That was just what I needed. That's how I thought it all fit togather but it just wasn't lining up, in the end I finally had to force some of the bolts in place, didn't like doing that very much, left a few scratches. Anyways THANKS AGAIN.

DURRTY · 08-10-2007, 04:40 AM

Hey one of your NUTS broke off. be carefull!!

OLDCHEV4X4 · 08-10-2007, 07:37 AM

Mine dont line up perfect either. I have to use a big punch to line up the 5/8" bolts.
205/th350 combo

**ELVINS** · 12-26-2024, 07:04 PM

thank you

Orange Crate · Yesterday, 11:19 PM

There are plenty of threads that recommend NOT installing that bracket as it does not allow the drive train to move under torque and that cracks the transmission to transfer case adapter. I left mine off the 72 K20.

08-03-2007, 05:42 PM	#1
tractorsx Registered User Join Date: Sep 2006 Location: Craig Co Posts: 17	Need pics. of transfer case mounts and bushings I pulled out trans. and transfer case a couple of month ago, I took pics but didn't get right detail. Now I'm trying to put it back in and can't figure out how the transfer case mount and bushings fit to the frame, nothing is lining up for me at this time? It in a 71 chevy 3/4 ton 4X4. Manual four speed trans. Thanks Last edited by tractorsx; 08-03-2007 at 05:44 PM.

08-03-2007, 08:01 PM	#2
msgross Registered User Join Date: Jul 2006 Location: Central PA Posts: 12,201	Re: Need pics. of transfer case mounts and bushings check out my build thread, should be the same... I can assist with any "detailed" pics that you need. __________________ The Garage: 1968 K-10 SWB - "Project Money Pit" 1996 Z-71 - "huntin rig" 1969 C-10 LWB (SOLD) "Project flip that truck or else" 1993 Passport, F@rd 1-ton (SOLD)"Project Cousin Eddie" My Garage Build "The 1,000 footer"

08-03-2007, 08:11 PM	#3
eedgell It's the air up here Join Date: Mar 2007 Location: Western Colorado Posts: 710	Re: Need pics. of transfer case mounts and bushings http://67-72chevytrucks.com/vboard/a...1&d=1186186077 Does this help? NP 205-4 speed, 1971 __________________ 1971 cheyenne k10 4 speed np 205 454 BB factory a/c Never drink down stream of the herd! Eric Last edited by eedgell; 08-19-2007 at 02:04 PM.

08-04-2007, 09:40 AM	#4
tractorsx Registered User Join Date: Sep 2006 Location: Craig Co Posts: 17	Re: Need pics. of transfer case mounts and bushings Thanks for the pics both of you guys, I looked at all of them, a couple of them were very close but I could'nt make out what I needed. I'll go outside in a short while and take pics of what I am looking for and what my problem is? I haven't posted pics on this board before, but I'll try. What I'm looking for is the placement of the bushings, and which half is top and bottom, there is a large and small half each? Attached Images

08-04-2007, 11:22 AM	#5
eedgell It's the air up here Join Date: Mar 2007 Location: Western Colorado Posts: 710	Re: Need pics. of transfer case mounts and bushings http://67-72chevytrucks.com/vboard/a...1&d=1186240631 The thicker bushings go between the lower frame rail lip, and the large bracket. The thinner bushings go between the larger and smaller bracket. The smaller bracket is bolted to the center of the frame, and the large bracket from the lower frame lip to the side of the T-case. Hope this helps. Attached Images __________________ 1971 cheyenne k10 4 speed np 205 454 BB factory a/c Never drink down stream of the herd! Eric

08-04-2007, 04:08 PM	#6
tractorsx Registered User Join Date: Sep 2006 Location: Craig Co Posts: 17	Re: Need pics. of transfer case mounts and bushings Thanks a million times for the pics eedgell!!! That was just what I needed. That's how I thought it all fit togather but it just wasn't lining up, in the end I finally had to force some of the bolts in place, didn't like doing that very much, left a few scratches. Anyways THANKS AGAIN.

08-10-2007, 04:40 AM	#7
DURRTY USMC Join Date: May 2007 Location: SLc,UT Posts: 300	Re: Need pics. of transfer case mounts and bushings Hey one of your NUTS broke off. be carefull!! __________________ Semper Fi

08-10-2007, 07:37 AM	#8
OLDCHEV4X4 Registered User Join Date: Apr 2000 Location: Chester County PA, USA Posts: 1,228	Re: Need pics. of transfer case mounts and bushings Mine dont line up perfect either. I have to use a big punch to line up the 5/8" bolts. 205/th350 combo __________________ 72 k/10 short wideside 72 k/5 Blazer 72 K/5 Blazer - obstacle course racer 72 custom/10 8' bed 70 K/5 Blazer 67 C-30 GMC Flat bed 86 GMC K2500 Plow Truck 85 GMC K3500 84 M1008 85 M1008 77 G30 Motor Home 72 Sears 12hp Tractor Glenmoore, Pennsylvania

12-26-2024, 07:04 PM	#9
ELVINS New Member Join Date: Dec 2024 Location: mesa arizona Posts: 5	Re: Need pics. of transfer case mounts and bushings thank you

Yesterday, 11:19 PM	#10
Orange Crate Registered User Join Date: Feb 2011 Location: Under the Truck Dreaming Posts: 753	Re: Need pics. of transfer case mounts and bushings There are plenty of threads that recommend NOT installing that bracket as it does not allow the drive train to move under torque and that cracks the transmission to transfer case adapter. I left mine off the 72 K20. __________________ 72 K20 Custom Camper, D60, 14BFF, full roller 406 TPI w custom built ECU and yes..it has tow hooks...and a 5 speed

Thread Tools
Show Printable Version Email this Page
Display Modes
Linear Mode Switch to Hybrid Mode Switch to Threaded Mode



Register or Log In To remove these advertisements.

Register or Log In To remove these advertisements.