Smoothing out sheetmetal???? - The 1947 - Present Chevrolet & GMC Truck Message Board Network

Alexis · 09-04-2004, 11:27 PM

What do you guys use after you welded something on, grinded the welds down to smooth the metal out? Sand paper, higher grit on the angled grinder? Or just be real soft with the die-grinder?

check out my work http://67-72chevytrucks.com/vboard/s...965#post943965

stllookn · 09-05-2004, 03:17 AM

If your welds are really good or you managed to weld it from the backside (not possible where you are welding on your truck but on some panels this is possible) you can use a right angle die grinder with the small spiral loc discs in 80 - 120 grit. I use my 4-inch right angle grinder to knock down my heavy welds and then finish them off with the air angle and the 80 - 120 grit disc.

*Gee_Emm* · 09-05-2004, 10:27 AM

Get some flap discs to go on your 4" angle grinder, they work great, I would never go back to anything else. For finishing in tight areas I use a angle die grinder with a 2" disc.

FRENCHBLUE72 · 09-05-2004, 11:35 AM

Those Flap Disk Are The Bomb!!

Alexis · 09-05-2004, 12:01 PM

sweet. thanks for the tip. Gonna have to stop by the hardware store.

dropdprpls10 · 09-05-2004, 12:30 PM

i use the flaper disks like Gee emm posted.. just gotta watch you dont lay on it to hard.. might not happen to you on a older truck but on the new sheet metal on late models its thinner and you can warp it.. if you watched trucks stacie used them when he was showing how to shave door handles and gas doors!!

Alexis · 09-05-2004, 07:41 PM

Home depot didn't have then, the OSH down the street from them didn't have them. Stopped by the OSH near my house to pick up some stuff and what'da you know, they had them. Picked on just 2. Just got to be nice with them and they do wounders. thanks guys!

09-04-2004, 11:27 PM	#1
Alexis Member since 2000 Join Date: Dec 2000 Location: Mountain View Ca / Mexico Posts: 7,874	Smoothing out sheetmetal???? What do you guys use after you welded something on, grinded the welds down to smooth the metal out? Sand paper, higher grit on the angled grinder? Or just be real soft with the die-grinder? check out my work http://67-72chevytrucks.com/vboard/s...965#post943965 Last edited by Alexis; 09-04-2004 at 11:52 PM.

09-05-2004, 03:17 AM	#2
stllookn Saving 1 truck at a time! Join Date: Aug 2001 Location: Kent, WA Posts: 6,465	If your welds are really good or you managed to weld it from the backside (not possible where you are welding on your truck but on some panels this is possible) you can use a right angle die grinder with the small spiral loc discs in 80 - 120 grit. I use my 4-inch right angle grinder to knock down my heavy welds and then finish them off with the air angle and the 80 - 120 grit disc. __________________ '68 C20 Longhorn 50th Anniversary 400/TH400 '68 C20 Longhorn 50th Anniversary 468/TH400w/buckets '72 C20 Halfhorn (Longhorn w/o cab and front clip) '69 Flxible Cruiser (look up ugly in the dictionary)

09-05-2004, 11:35 AM	#4
FRENCHBLUE72 PROJECT 7DEUCE Join Date: Dec 2002 Location: GRANTS PASS OR Posts: 21,606	Those Flap Disk Are The Bomb!! __________________ GO BIG GREEN GO DUCKS MEMBER #6377 72 k-5 daily driver 6'' lift 35'' 350-350-205 slowly getting rust free. Project "7DEUCE" check out my build http://67-72chevytrucks.com/vboard/s...d.php?t=267665 Tim Powell..R.I.P EastSideLowlife..... R.I.P..

Thread Tools
Show Printable Version Email this Page
Display Modes
Linear Mode Switch to Hybrid Mode Switch to Threaded Mode

09-05-2004, 10:27 AM	#3
Gee_Emm Account Suspended Join Date: Sep 2000 Posts: 3,991	Get some flap discs to go on your 4" angle grinder, they work great, I would never go back to anything else. For finishing in tight areas I use a angle die grinder with a 2" disc.

09-05-2004, 12:01 PM	#5
Alexis Member since 2000 Join Date: Dec 2000 Location: Mountain View Ca / Mexico Posts: 7,874	sweet. thanks for the tip. Gonna have to stop by the hardware store.

09-05-2004, 12:30 PM	#6
dropdprpls10 Registered User Join Date: Jun 2004 Location: Reading PA Posts: 164	i use the flaper disks like Gee emm posted.. just gotta watch you dont lay on it to hard.. might not happen to you on a older truck but on the new sheet metal on late models its thinner and you can warp it.. if you watched trucks stacie used them when he was showing how to shave door handles and gas doors!!

09-05-2004, 07:41 PM	#7
Alexis Member since 2000 Join Date: Dec 2000 Location: Mountain View Ca / Mexico Posts: 7,874	Home depot didn't have then, the OSH down the street from them didn't have them. Stopped by the OSH near my house to pick up some stuff and what'da you know, they had them. Picked on just 2. Just got to be nice with them and they do wounders. thanks guys!



Register or Log In To remove these advertisements.

Register or Log In To remove these advertisements.