Need a passenger side door latch assembly - The 1947 - Present Chevrolet & GMC Truck Message Board Network

70c10 · 10-08-2004, 10:36 PM

Anybody have one cheap?. I need one for a 70'. I need just the latch assembly in the door. How much shipped to 21236?. Thanks

vtblazer · 10-09-2004, 06:20 AM

Yeah, I do.
Do you need both the door part and the jamb pieces? or just what's in the door?

MOTHERTRUCKERS · 10-09-2004, 08:03 AM

New latch 49.00 shipping included used 20.00 shipping included.

Huck · 10-09-2004, 08:37 AM

FYI, the door latch mech that is mounted within the door has a tendancy to have the center pivot pin break loose from the outer support housing which causes a problem. The latch roller gets cocked crooked. You can just spot weld this pin to the outer housing and the problem goes away.
If yours is totally shot, I have several that I believe are good---will send you one for the cost of shipping-----(re-you did the same of me a few years back on sway bar bckts!!!) returning the favor! Just send me you address via e-mail and I will get-er-done!!!

70c10 · 10-09-2004, 12:10 PM

PM sent

70c10 · 10-11-2004, 10:25 AM

Is the PM function working?. I'm desperate here

. I will pay right away with Paypal if somebody has one ready to ship.

70c10 · 10-11-2004, 10:20 PM

ttt

cableguy0 · 10-11-2004, 10:24 PM

hey jim i got one in a door from a 69 i would have to yank it outta the door but u can have im never going to use it. it worked when i took the truck apart

70c10 · 10-11-2004, 10:33 PM

Thanks Jason. PM being sent.

cableguy0 · 10-11-2004, 10:34 PM

it told me i couldnt pm you says ur box is full

70c10 · 10-11-2004, 10:41 PM

Not now

pickupman · 10-11-2004, 11:18 PM

Jim, If you can't find any I should have some good used ones. I can check at the shop tomorrow.
Bill

70c10 · 10-12-2004, 07:36 AM

Thanks Bill, If I run into problems, I'll give you a shout!.

10-08-2004, 10:36 PM	#1
70c10 67-72 Addict! Join Date: Feb 2002 Location: The TAX State! Posts: 7,857	Need a passenger side door latch assembly Anybody have one cheap?. I need one for a 70'. I need just the latch assembly in the door. How much shipped to 21236?. Thanks __________________ Jim 1970 C/10 Fleetside w/Ghost Flames Lowered 4.5" front and 4" rear (Raked) 355/350 Turbo w/shift kit 10" Redneck Performance Verter w/2500 stall Hooker Super Comps part#2808-1 Performer RPM Air-Gap 12 Bolt w/3:73 gears- Eaton Posi Comp Cams XE262 with 1.6 Crane Energizers, Road Demon 625 and Brodix IK 180 heads Last edited by 70c10; 10-09-2004 at 12:21 AM.

10-09-2004, 06:20 AM	#2
vtblazer Registered User Join Date: Oct 2003 Location: Central Vermont Posts: 8,538	Door Latch Yeah, I do. Do you need both the door part and the jamb pieces? or just what's in the door?

10-09-2004, 08:03 AM	#3
MOTHERTRUCKERS Registered User Join Date: Dec 1999 Location: BRADENTON FLA Posts: 3,269	New latch 49.00 shipping included used 20.00 shipping included. __________________ Rest in Peace Ed. Thanks for all the good times.

10-09-2004, 08:37 AM	#4
Huck Senior Member Join Date: Jun 2001 Location: Shelbyville, KY Posts: 3,269	Door Latch FYI, the door latch mech that is mounted within the door has a tendancy to have the center pivot pin break loose from the outer support housing which causes a problem. The latch roller gets cocked crooked. You can just spot weld this pin to the outer housing and the problem goes away. If yours is totally shot, I have several that I believe are good---will send you one for the cost of shipping-----(re-you did the same of me a few years back on sway bar bckts!!!) returning the favor! Just send me you address via e-mail and I will get-er-done!!!

10-09-2004, 12:10 PM	#5
70c10 67-72 Addict! Join Date: Feb 2002 Location: The TAX State! Posts: 7,857	PM sent __________________ Jim 1970 C/10 Fleetside w/Ghost Flames Lowered 4.5" front and 4" rear (Raked) 355/350 Turbo w/shift kit 10" Redneck Performance Verter w/2500 stall Hooker Super Comps part#2808-1 Performer RPM Air-Gap 12 Bolt w/3:73 gears- Eaton Posi Comp Cams XE262 with 1.6 Crane Energizers, Road Demon 625 and Brodix IK 180 heads

10-11-2004, 10:25 AM	#6
70c10 67-72 Addict! Join Date: Feb 2002 Location: The TAX State! Posts: 7,857	Is the PM function working?. I'm desperate here . I will pay right away with Paypal if somebody has one ready to ship. __________________ Jim 1970 C/10 Fleetside w/Ghost Flames Lowered 4.5" front and 4" rear (Raked) 355/350 Turbo w/shift kit 10" Redneck Performance Verter w/2500 stall Hooker Super Comps part#2808-1 Performer RPM Air-Gap 12 Bolt w/3:73 gears- Eaton Posi Comp Cams XE262 with 1.6 Crane Energizers, Road Demon 625 and Brodix IK 180 heads

10-11-2004, 10:20 PM	#7
70c10 67-72 Addict! Join Date: Feb 2002 Location: The TAX State! Posts: 7,857	ttt __________________ Jim 1970 C/10 Fleetside w/Ghost Flames Lowered 4.5" front and 4" rear (Raked) 355/350 Turbo w/shift kit 10" Redneck Performance Verter w/2500 stall Hooker Super Comps part#2808-1 Performer RPM Air-Gap 12 Bolt w/3:73 gears- Eaton Posi Comp Cams XE262 with 1.6 Crane Energizers, Road Demon 625 and Brodix IK 180 heads

10-11-2004, 10:24 PM	#8
cableguy0 Senior Member Join Date: Apr 2000 Location: Delta,Pa Posts: 14,950	hey jim i got one in a door from a 69 i would have to yank it outta the door but u can have im never going to use it. it worked when i took the truck apart __________________ Owner of North Point Car Care in Dundalk Md. We specialize in custom exhaust on both modern and classic vehicles. We are a full service auto shop from classics to modern vehicles. Feel free to contact me with questions. I will give a 10% discount to any board member.

10-11-2004, 10:33 PM	#9
70c10 67-72 Addict! Join Date: Feb 2002 Location: The TAX State! Posts: 7,857	Thanks Jason. PM being sent. __________________ Jim 1970 C/10 Fleetside w/Ghost Flames Lowered 4.5" front and 4" rear (Raked) 355/350 Turbo w/shift kit 10" Redneck Performance Verter w/2500 stall Hooker Super Comps part#2808-1 Performer RPM Air-Gap 12 Bolt w/3:73 gears- Eaton Posi Comp Cams XE262 with 1.6 Crane Energizers, Road Demon 625 and Brodix IK 180 heads

10-11-2004, 10:34 PM	#10
cableguy0 Senior Member Join Date: Apr 2000 Location: Delta,Pa Posts: 14,950	it told me i couldnt pm you says ur box is full __________________ Owner of North Point Car Care in Dundalk Md. We specialize in custom exhaust on both modern and classic vehicles. We are a full service auto shop from classics to modern vehicles. Feel free to contact me with questions. I will give a 10% discount to any board member.

10-11-2004, 10:41 PM	#11
70c10 67-72 Addict! Join Date: Feb 2002 Location: The TAX State! Posts: 7,857	Not now __________________ Jim 1970 C/10 Fleetside w/Ghost Flames Lowered 4.5" front and 4" rear (Raked) 355/350 Turbo w/shift kit 10" Redneck Performance Verter w/2500 stall Hooker Super Comps part#2808-1 Performer RPM Air-Gap 12 Bolt w/3:73 gears- Eaton Posi Comp Cams XE262 with 1.6 Crane Energizers, Road Demon 625 and Brodix IK 180 heads

10-11-2004, 11:18 PM	#12
pickupman Registered User Join Date: Dec 2000 Location: Greeneville, TN Posts: 3,095	Jim, If you can't find any I should have some good used ones. I can check at the shop tomorrow. Bill __________________ atheystruck@comcast.net 67 1/2 ton 4wd custom cab 72 1/2 ton 4wd super cheyenne 71 1/2 BB super cheyenne shortbed

10-12-2004, 07:36 AM	#13
70c10 67-72 Addict! Join Date: Feb 2002 Location: The TAX State! Posts: 7,857	Thanks Bill, If I run into problems, I'll give you a shout!. __________________ Jim 1970 C/10 Fleetside w/Ghost Flames Lowered 4.5" front and 4" rear (Raked) 355/350 Turbo w/shift kit 10" Redneck Performance Verter w/2500 stall Hooker Super Comps part#2808-1 Performer RPM Air-Gap 12 Bolt w/3:73 gears- Eaton Posi Comp Cams XE262 with 1.6 Crane Energizers, Road Demon 625 and Brodix IK 180 heads

Thread Tools
Show Printable Version Email this Page
Display Modes
Linear Mode Switch to Hybrid Mode Switch to Threaded Mode



Register or Log In To remove these advertisements.

Register or Log In To remove these advertisements.