My 73 c10 project.....

[lolife99]

Are you going to have to raise the transmisson tunnel sheetmetal?

[luifer76]

Originally Posted by lolife99

Are you going to have to raise the transmisson tunnel sheetmetal?

yup im gonna have raise it up too....

[Pro Performance]

Looking good man...

[luifer76]

Originally Posted by Pro Performance

Looking good man...

thanks bro i can't wait until i see this thing on the ground again but lower lol...

[luifer76]

got a little more work done today i started to plate the Z from the outside and inside to secure it a little more....

[luifer76]

a little diamond plate action lol..... hey i have it why not use it right?...

[luifer76]

i also boxed in the horns where they were cut and brought down....

[Nobaddaze]

lookin good!

[luifer76]

Originally Posted by Nobaddaze

lookin good!

thanks bro i need to get this thing to lay lower.....

[luifer76]

next thing to do is the part i hate the most weding the 2X4 inside the frame and cutting the bottom of the frame more pics to come....

[mooseknuckles]

looks good brother.

[luifer76]

thanks bro not alot of feedback on this site i thougth i would get more feedback here than on the C10 FORUM cause there is more members here but i guess i was wrong....

[canadian 4x4]

how big is your Z? Truck looks wicked man! very jealous of your rides!

[luifer76]

more work done today..... i got the 2X4 trimmed to fit the inside of the frame and i cleaned it up for better penetration and i started to weld it in place sorry about the crappy pics........

[luifer76]

Originally Posted by canadian 4x4

how big is your Z? Truck looks wicked man! very jealous of your rides!

thanks man...... is a 3 Inch Z

[luifer76]

i also got the cab mounts all welded up...

[lolife99]

You're not messing around.
Keep up the good work!

[canadian 4x4]

I have a frame that i want to start bagging, how long is the 2x4 and how are you determining where to put it? i see its angled, is that to the front or the back? i cant really tell from the pics

[luifer76]

i hate this part but in the next couple days im gonna be cutting the bottom of the frame...... got to go to lowes and pick up some good sawzall blades cause my grinder and cutting wheels wont cut it for this....

[luifer76]

Originally Posted by lolife99

You're not messing around.
Keep up the good work!

thanks bro....

[luifer76]

Originally Posted by canadian 4x4

I have a frame that i want to start bagging, how long is the 2x4 and how are you determining where to put it? i see its angled, is that to the front or the back? i cant really tell from the pics

the 2X4 is around 4 feet long and what you want to do is located where the lowest point of the frame is which normally hangs pass the pinch weld the whole purpose is to get rid of the lowest point of the frame so the cab becames the lowest at that point.... just c clamp the 2X4 against the top and it will line up by itself...

[luifer76]

it looks like is angled because the frame starts going up towards the rear of the cab but is actually against the top of the frame and c clamped to hold it in place so the top of the frame and the 2x4 is welded together....

[luifer76]

well i got some more work done in the last two days but i couldn't post any updates cause my internet modem took a crap and i had to go exchange it at the local cable office but here is what i did yesterday and today... i got the bottom of the frame trimmed on both sides....

[luifer76]

the dewalt demolition blades worked out pretty good....

[luifer76]

some upside down welding not fun at all....