FS - Parting out 90 Suburban

[bigarmzz]

Originally Posted by LILREDGMC

Back from the trip.

The core support had rust, obviously it is a PA suburban, at the vertical boxes where they intersect the lower rail. I won't sell it here as it's not worthy to ship or have someone receive it and freak out. Not fair to the board. Sorry Bigarmzz,

Would like to keep the interior as a whole.

Rear differential gone.

Front bumper gone.

Thanks

LILREDGMC

doh

these things are gettin harder to find i guess

[raiders3581]

is the factory radio still there? is there pictures of it availble

[LILREDGMC]

Pics of what I recall are 3/4 ton 4wd. The other one under the truck is 1/2 ton suburban, only one piece, I expected two piece.

[LILREDGMC]

Now the pics

Rear 3/4 ton on right two piece

one front shaft with knuckle

one two piece with carrier ?

89 Sub 1/2 ton one piece

[BIGCHEVYMAN]

i need the little chrome covers that are on the end of the door pull straps. how much you for all of the good ones.

[pat]

If you have it could you post a pic of the left front sidemarker? I need the lense and chrome trim around it.
Thanks

[Blue_71]

i cant tell, but on th ebackseat is there a bench seat "saddle blanket" cover? if so how much shipped to 42141? (just the saddle blanket cover)

[BIGCHEVYMAN]

i need those covers, how much?

[Walts_restoration]

Interior cosists of what, and what kind of shipping to lawrence, ks 66049? thanks

[LILREDGMC]

Sorry for the delay, didn't see your post Walt, and went off to the Brickyard for the trucks, Busch, and Nextel.

The interior would be all seats, door panels overhead console, side panels, seatbelts and floor holders (plastic bases)

You would not get the column, the dash or cluster or woodgrain, nor the worn carpet cover for the tailgate which left with the gate. I could include the plastic A, B and C pillar covers as well.

We can discuss any other pieces I may be "missing" in this short inventory. If there are specific pieces you have to have, make me aware.

Blue 71 and BIGCHEVYMAN, I will check if all seats are covered. I believe one was not but need to crawl back there tonight.

[C&C Chevy]

What kind of shape are the front window regulators in? Wold you be willing to part them out and ship if they are decent shape? Only need drivers side but would be willing to take passenger one as well for a backup. Let me know, thanks.

[LILREDGMC]

Sorry for the delays.

But from the top I'll try to cover everyone.

Special K - 241 Transfer - give me a call or email Heading to Bmore soon

BigChevyMan - Seat covers are only buckets and third seat, Chuck had taken the 2nd off, it was in his basement, then he pitched it not knowing someone out there might want it. So, back at you for 2 out of 3 ?

Chrome covers are 3 of 4 and appear decent. No clue on price - $5 + shipping?

Paul 72 - did you find a shaft? or do any of those look like what you might need.

Pat - Will take pic of left fender light, it is there and appeared decent, but that was from 100 feet in one of four thunderstorms yesterday.

Raiders3581 - Will take pic of bezel at radio, the on off button I recall was replaced from the original but not sure what it looks like.

Walt - Any ideas on the whole interior??

CC Chevy - regulators with or with out motors? They ran ok and didn't have any lost motion.

KurtL - Radio bezel pic tonight.


Any interest in smoke glass from side doors and rear quarter windows??

Front differential 342 ??

Scrap yard looms for the hulk

Get back with Pics this evening

THanks for your patience.

LILREDGMC

[BIGCHEVYMAN]

snap me a pic of those covers on both sides thanks

[LILREDGMC]

BIGCHEVY

When you say both sides, ? , the buckets and the back seat or ?

I'll get a pic of all either Sat or Sun.

Radio and surround. The red dot is the new on/off switch




Seat covers for Big Chevy




Side Marker - Both fronts are similar, not sure if it is paint or plastic on the leaking edge ??


I'll recheck in the morning for what I may have omitted or need to post pics of.

Thanks

LILREDGMC

[LILREDGMC]

Walts Resto - Didn't thoroughly read your post, I apologize.

The interior is complete, i.e. door panels, seats,buckets and two rear seats, console,ABC pillar and misc can go with it if you want it. The instrument cluster and bezel, column, and dash(cracked) is not with. The overhead console can go with it.
As far as shipping, that may be the ugly. It needs to be enclosed for protection, but the size could be a killer. Anyone have any ideas. I may be heading west with a vehicle, but it's not on the books right now.

Anyone on the shipping or crating. Need a box van heading west.

Thanks Walt.

[BIGCHEVYMAN]

I need the small chrome pecies that fit over the end of the door pull straps. I don't need anything from the seats.

[62 short step]

Sent you a pm.

[LILREDGMC]

62 Short Step with a PM

Timing may not work, do you have a good pic of the plates, do any other's work. I may have a few others, might even be the same ones.

LILREDGMC

BIGCHEVY

I will check the three chrome pull strap ends and get pics.

[C&C Chevy]

With motors are great, easier to install, just let me now on the price for both front door units. Thanks.

[jkade]

What about the wheels? 6 lug factory aluminum?
Thanks

[Mickey_D]

What size are those rims? Are they 15's or 16's? If they are 16's I would be very much interested in them as only one wrecking yard around here has a set and they want $140 for all 4 (non-matching steels), which of course I made the sounds of having a heart attack and hung up on them.....

[LILREDGMC]

Back from another work ordeal. Now to catch up.

Mickey/jkade
Wheels are 15" factory, show flaking did not look at for serious curb rash or not. I don't recall much, but will recheck. Flaking and or corrosion is evident. Will post 4 pics of wheels.

thought they didn't change to 16 until the newer style Burb

[project 67 sub]

do you have the motor mount towers? are they for a small block chevy? if you have them are they in good condition and how much would you possibly want for them? can you get pics of them?

[crews]

Is the interior still available? Do the rear interior panels in the cargo area come included for the price quoted?

[BLE 'BURBAN]

How much for the Rear side door lock solenoids & linkage, window regulators with motors and the wiring harness's in both rear side doors? These I need to finish installing power windows/locks in my '90 v2500 'burb. Oh and shipping to zip code 99517 (Anchorage, Alaska)