updated pics of my truck.. - Page 2 - The 1947 - Present Chevrolet & GMC Truck Message Board Network

lotik · 01-04-2003, 01:20 AM

stock floor. 2x3 box tubing under the cab and reinforced. bedfloor raised in rear, core support lowered into frame. cut out holes in the floor for transmission. BTW, new 350 crate and new 700r4 are in. not too much longer.

NSANE68!!! · 01-04-2003, 01:25 AM

Did you have to raise the tranny hump after the B-drop?

lotik · 01-04-2003, 01:28 AM

yes, but i did have a low tanny hump, so i dunno about a high hump (if that applies to you).

NSANE68!!! · 01-04-2003, 01:31 AM

yea I got the low hump too. Any pics of the hump, and how far did you raise it? Just cut and piece it in?

lotik · 01-04-2003, 01:34 AM

actually its still just a hole. i had to get the tranny in there so i could see how the sheet metal need to be fitted. i am probably going to just rivet some metal in since it will be covered. i also had to cut two small holes for the frame to come through at the front where the cab sits down in the frame. i will get a pic tomorrow to explain better.

Chevy_68 · 01-06-2003, 11:18 PM

bad truck post some pics on the hole process of the body drop of course. keep up the good work

01-04-2003, 01:20 AM	#26
lotik drag it like you stole it Join Date: Feb 2002 Location: Louisiana Posts: 542	stock floor. 2x3 box tubing under the cab and reinforced. bedfloor raised in rear, core support lowered into frame. cut out holes in the floor for transmission. BTW, new 350 crate and new 700r4 are in. not too much longer. __________________ negative camber //LA\\

01-04-2003, 01:25 AM	#27
NSANE68!!! SLICER AND DICIER Join Date: May 2001 Location: Quuen Creek Posts: 1,383	Did you have to raise the tranny hump after the B-drop? __________________ 01 Tahoe 22's 2/4 drop and tv's 68 chevy money pit 51 chevy belair 95 Honda 900RR 05 GMC Siearra (company truck)

01-04-2003, 01:28 AM	#28
lotik drag it like you stole it Join Date: Feb 2002 Location: Louisiana Posts: 542	yes, but i did have a low tanny hump, so i dunno about a high hump (if that applies to you). __________________ negative camber //LA\\

01-04-2003, 01:31 AM	#29
NSANE68!!! SLICER AND DICIER Join Date: May 2001 Location: Quuen Creek Posts: 1,383	yea I got the low hump too. Any pics of the hump, and how far did you raise it? Just cut and piece it in? __________________ 01 Tahoe 22's 2/4 drop and tv's 68 chevy money pit 51 chevy belair 95 Honda 900RR 05 GMC Siearra (company truck)

01-04-2003, 01:34 AM	#30
lotik drag it like you stole it Join Date: Feb 2002 Location: Louisiana Posts: 542	actually its still just a hole. i had to get the tranny in there so i could see how the sheet metal need to be fitted. i am probably going to just rivet some metal in since it will be covered. i also had to cut two small holes for the frame to come through at the front where the cab sits down in the frame. i will get a pic tomorrow to explain better. __________________ negative camber //LA\\

01-06-2003, 11:18 PM	#31
Chevy_68 Registered User Join Date: Mar 2002 Location: PHX Az Posts: 155	bad truck post some pics on the hole process of the body drop of course. keep up the good work

Thread Tools
Show Printable Version Email this Page
Display Modes
Linear Mode Switch to Hybrid Mode Switch to Threaded Mode



Register or Log In To remove these advertisements.

Register or Log In To remove these advertisements.