Project "RACE TRUCK" aka "Last of the spare parts" build - Page 2 - The 1947 - Present Chevrolet & GMC Truck Message Board Network

72freak · 11-11-2010, 06:44 AM

Floor shifter from Greg, 3 speed x-member from UNCLE and a fairly nice fleetside bed "oldschool" found at a junkyard showed up also this week.....this project is moving along!!!!

**special-K** · 11-11-2010, 07:00 AM

Gitter done for the next race season!

Old School Kid · 01-25-2011, 09:08 PM

Need a little help... Have a lead on getting a 1988 S-10 T-5 transmission... I am wanting to put it behind a 250 6 cylinder.. We have the bell housing to run a Saginaw...I know that the input shaft is about 9/16" too long on the S-10 T-5,so a spacer will be needed... I would assume that we get the clutch that goes with the 1988 S-10 t-5?

So all that we need to do is use the Saginaw bell housing, 9/16"spacer, and new clutch for the s-10? Are we missing anything?

Any help or input would be greatly appreciated!

Race truck needs your help!!!

http://hamiltonintakes.com/products/...57-chevy-truck

72freak · 01-27-2011, 07:19 PM

The T5 experts are wearing this one out!!!

Old School Kid · 01-27-2011, 08:31 PM

Ditto!! Race truck needs your help!

**Zeke's Garage** · 01-28-2011, 04:20 PM

Double check the bell housing you've got, it might fit without the need for a spacer. This is what I understand for the swap..

If you've got a Camaro transmission, the input spline is the right length, you'll just need to get a clutch disc for the Camaro. But the tailshaft is a bit longer and it will put your shifter right at the edge of the bench seat.

If you've got an S10 transmission, the input spline and the collar will need to be trimmed to match the original 3 speed. And the shifter location will work just fine.

You can get and adapter/spacer that will take care of all the input spline/spacer issues for your existing bellhousing, but it seemed kind of pricey for what it was (~$150 or so).

So it seems the 'best' way is to get a camaro transmission which mounts up to the bellhousing, then use an S10 tailshaft so that the shifter location is in the best spot, and you have to do less work on the input end.

I'll try to dig up the other sources of parts for this, as I'm looking to put a T5 in my '67 with an I6 and fuel injection.

Shawn

Jeez, I just noticed that everyone on this thread is in NE GA... we should get together and hash it out. I could use some motivation to start work on mine again.

72freak · 01-28-2011, 08:26 PM

[QUOTE=

Jeez, I just noticed that everyone on this thread is in NE GA... we should get together and hash it out. I could use some motivation to start work on mine again.[/QUOTE]

We did it last year up in Canton....at a BBQ spot. Maybe it can happen again.

Old School Kid · 01-28-2011, 09:35 PM

Great... Thanks Zeke's Garage for the simple to the point information..... That's what I was looking for

I like BBQ! ( Need to post in GA section!)

72freak · 01-29-2011, 06:19 PM

She got her powerplant today!!!! RACE MOTOR!!!

Now we need the T5

Old School Kid · 01-30-2011, 09:33 AM

One mans "Poo Poo" is another mans "Race Motor"!

Thanks 72freak for some greasy fun...

72freak · 02-09-2011, 06:13 AM

Still waiting on the T5, electric water pump, electric fuel pump, gear driven timing chain, split header, dual carb manifold and blower. Come on "Old School" it cant be a race truck withough it! Have you given any thought to some nitros?

72freak · 02-15-2011, 10:22 PM

We did some special race modifications today to the engine and we should have the transmission strapped to it and drive shaft in by the end of the week.

Old School Kid · 02-15-2011, 10:30 PM

yesssssssssss!

quickstrikez06 · 02-15-2011, 11:35 PM

Hey guys... My truck is currently in Snellville. In the middle of Gwinnett. Im looking for someone that can take the body off and do a tear down, clean, and suspension rebuild. You guys have someone you can recommend? My thread is on here... Its called Dads old 72.

http://67-72chevytrucks.com/vboard/s...d.php?t=446960

Its got a 307 in it and Im looking to get rid of it, the cab, the tranny, and rear end.

**Zeke's Garage** · 02-16-2011, 12:15 PM

Quote:

Originally Posted by quickstrikez06

Hey guys... My truck is currently in Snellville. In the middle of Gwinnett. Im looking for someone that can take the body off and do a tear down, clean, and suspension rebuild. You guys have someone you can recommend? My thread is on here... Its called Dads old 72.

http://67-72chevytrucks.com/vboard/s...d.php?t=446960

Its got a 307 in it and Im looking to get rid of it, the cab, the tranny, and rear end.

Quickstrike... PM sent.

Shawn

72freak · 02-16-2011, 02:07 PM

Quote:

Originally Posted by quickstrikez06

Hey guys... My truck is currently in Snellville. In the middle of Gwinnett. Im looking for someone that can take the body off and do a tear down, clean, and suspension rebuild. You guys have someone you can recommend? My thread is on here... Its called Dads old 72.

http://67-72chevytrucks.com/vboard/s...d.php?t=446960

Its got a 307 in it and Im looking to get rid of it, the cab, the tranny, and rear end.

As far as transporting one locally, stripping it down, getting rid of unecessary parts, removing cab, labeling and bagging parts, checking and replacing steering and suspension components...we can do that type of work all day long. We can budget build or get it ready for you or someone else to go crazy with it.

72freak · 02-19-2011, 10:05 PM

Engine, clutch, transmission and shifter are all mounted. Driveshaft and cab to come soon! It gets racier every day!!!

OrangeCrush1970 · 02-20-2011, 01:41 PM

That "popping Noise" when we were pushing it was my ankle!!!

72freak · 02-24-2011, 07:52 AM

Big weekend to come.....going to get a cab and possibly some wiring!

Racier every day!

72freak · 02-26-2011, 05:29 PM

She got a cab, some fresh brake lines and a new master cylinder today along with some rattle can brown RACE paint! Check out that RACE EXHAUST!!!

67chevy1series · 02-26-2011, 05:34 PM

lookin good! now you just need the front clip on!

72freak · 02-26-2011, 05:50 PM

Quote:

Originally Posted by 67chevy1series

lookin good! now you just need the front clip on!

We have a 68 front clip to put on it but we are needing a core support. All in good time!

OrangeCrush1970 · 02-26-2011, 07:13 PM

What is that ORANGE thing looming in the background???? Could that be.....another race truck!?!?! Looking good!

68steppsidee · 02-26-2011, 07:43 PM

Where'd the stepside bed go?

JasonBird · 02-26-2011, 08:49 PM

where's the parachute go? maybe it's in the mail...

11-11-2010, 06:44 AM	#26
72freak Rottenwood Garage Member Join Date: May 2005 Location: Marietta, Georgia Posts: 4,321	Re: Project "RACE TRUCK" aka "Last of the spare parts" build Floor shifter from Greg, 3 speed x-member from UNCLE and a fairly nice fleetside bed "oldschool" found at a junkyard showed up also this week.....this project is moving along!!!! __________________ 2004 Chevrolet Suburban C1500 2001 Chevrolet 2500HD Crew 6.0 1999 Harley Davidson Electra Glide 1972 Chevrolet C-20 Custom Camper "Dump Truck" 1972 Chevrolet C-20 Suburban "Big Green" 1969 Chevrolet C-50 Wedge Hauler "Leonidis" 1966 C-10 2x4 short fleet 327 4 speed "Race Truck" 1952 Plymouth Cranbrook "Rican" (my grandfathers) 1931 Ford Model A Coupe "Black Beauty" 1930 Ford Model A truck "Club Cab" 4x4 Rottenwood Garage and Speed Shop.....where everything must be racy! *It's not just a hobby..It's a LIFESTYLE!!!* Thanks for nothing Barrett-Jackson You cant fix stupid or teach accountability! Time wasters, looky Lous and tire kickers are everywhere! Last edited by 72freak; 11-11-2010 at 06:45 AM.

11-11-2010, 07:00 AM	#27
special-K Special Order Join Date: Nov 2004 Location: Mt Airy, MD Posts: 85,851	Re: Project "RACE TRUCK" aka "Last of the spare parts" build Gitter done for the next race season! __________________ "BUILDING A BETTER WAY TO SERVE THE USA"......67/72......"The New Breed" GMC '67 C1500 Wideside Super Custom SWB: 327/M22/3.42 posi.........."The '67" (project) GMC '72 K2500 Wideside Sierra Custom Camper: 350/TH350/4.10 Power-Lok..."The '72" (rolling) Tim "Don't call me a redneck. I'm a rough cut country gentleman" R.I.P. ~ East Side Low Life ~ El Jay ~ 72BLUZ ~ Fasteddie69 ~ Ron586 ~ 67ChevyRedneck ~ Grumpy Old Man ~

01-25-2011, 09:08 PM	#28
Old School Kid Rottenwood Garage Member..Yes! Join Date: Oct 2008 Location: Marietta, Georgia Posts: 174	Re: Project "RACE TRUCK" aka "Last of the spare parts" build Need a little help... Have a lead on getting a 1988 S-10 T-5 transmission... I am wanting to put it behind a 250 6 cylinder.. We have the bell housing to run a Saginaw...I know that the input shaft is about 9/16" too long on the S-10 T-5,so a spacer will be needed... I would assume that we get the clutch that goes with the 1988 S-10 t-5? So all that we need to do is use the Saginaw bell housing, 9/16"spacer, and new clutch for the s-10? Are we missing anything? Any help or input would be greatly appreciated! Race truck needs your help!!! http://hamiltonintakes.com/products/...57-chevy-truck __________________ When interests become diversified, not all can be Barrett Jackson. Budgets and Accountants get in the way. My 65 (SOLD) http://67-72chevytrucks.com/vboard/s...d.php?t=317013 My 51 (SOLD) http://67-72chevytrucks.com/vboard/s...80#post3551880 Racetruck III (SOLD) http://67-72chevytrucks.com/vboard/s...72#post4254972 Rottenwood Garage and Speed Shop.....where everything must be racy! Gone to dark side for a while...1966 F100 in the stable Last edited by Old School Kid; 01-25-2011 at 09:12 PM.

01-27-2011, 07:19 PM	#29
72freak Rottenwood Garage Member Join Date: May 2005 Location: Marietta, Georgia Posts: 4,321	Re: Project "RACE TRUCK" aka "Last of the spare parts" build The T5 experts are wearing this one out!!! __________________ 2004 Chevrolet Suburban C1500 2001 Chevrolet 2500HD Crew 6.0 1999 Harley Davidson Electra Glide 1972 Chevrolet C-20 Custom Camper "Dump Truck" 1972 Chevrolet C-20 Suburban "Big Green" 1969 Chevrolet C-50 Wedge Hauler "Leonidis" 1966 C-10 2x4 short fleet 327 4 speed "Race Truck" 1952 Plymouth Cranbrook "Rican" (my grandfathers) 1931 Ford Model A Coupe "Black Beauty" 1930 Ford Model A truck "Club Cab" 4x4 Rottenwood Garage and Speed Shop.....where everything must be racy! *It's not just a hobby..It's a LIFESTYLE!!!* Thanks for nothing Barrett-Jackson You cant fix stupid or teach accountability! Time wasters, looky Lous and tire kickers are everywhere!

01-27-2011, 08:31 PM	#30
Old School Kid Rottenwood Garage Member..Yes! Join Date: Oct 2008 Location: Marietta, Georgia Posts: 174	Re: Project "RACE TRUCK" aka "Last of the spare parts" build Ditto!! Race truck needs your help! __________________ When interests become diversified, not all can be Barrett Jackson. Budgets and Accountants get in the way. My 65 (SOLD) http://67-72chevytrucks.com/vboard/s...d.php?t=317013 My 51 (SOLD) http://67-72chevytrucks.com/vboard/s...80#post3551880 Racetruck III (SOLD) http://67-72chevytrucks.com/vboard/s...72#post4254972 Rottenwood Garage and Speed Shop.....where everything must be racy! Gone to dark side for a while...1966 F100 in the stable

01-28-2011, 04:20 PM	#31
Zeke's Garage Senior Member Join Date: Feb 2010 Location: Kennesaw, GA Posts: 288	Re: Project "RACE TRUCK" aka "Last of the spare parts" build Double check the bell housing you've got, it might fit without the need for a spacer. This is what I understand for the swap.. If you've got a Camaro transmission, the input spline is the right length, you'll just need to get a clutch disc for the Camaro. But the tailshaft is a bit longer and it will put your shifter right at the edge of the bench seat. If you've got an S10 transmission, the input spline and the collar will need to be trimmed to match the original 3 speed. And the shifter location will work just fine. You can get and adapter/spacer that will take care of all the input spline/spacer issues for your existing bellhousing, but it seemed kind of pricey for what it was (~$150 or so). So it seems the 'best' way is to get a camaro transmission which mounts up to the bellhousing, then use an S10 tailshaft so that the shifter location is in the best spot, and you have to do less work on the input end. I'll try to dig up the other sources of parts for this, as I'm looking to put a T5 in my '67 with an I6 and fuel injection. Shawn Jeez, I just noticed that everyone on this thread is in NE GA... we should get together and hash it out. I could use some motivation to start work on mine again. Last edited by Zeke's Garage; 01-28-2011 at 04:23 PM.

01-28-2011, 08:26 PM	#32
72freak Rottenwood Garage Member Join Date: May 2005 Location: Marietta, Georgia Posts: 4,321	Re: Project "RACE TRUCK" aka "Last of the spare parts" build [QUOTE= Jeez, I just noticed that everyone on this thread is in NE GA... we should get together and hash it out. I could use some motivation to start work on mine again.[/QUOTE] We did it last year up in Canton....at a BBQ spot. Maybe it can happen again. __________________ 2004 Chevrolet Suburban C1500 2001 Chevrolet 2500HD Crew 6.0 1999 Harley Davidson Electra Glide 1972 Chevrolet C-20 Custom Camper "Dump Truck" 1972 Chevrolet C-20 Suburban "Big Green" 1969 Chevrolet C-50 Wedge Hauler "Leonidis" 1966 C-10 2x4 short fleet 327 4 speed "Race Truck" 1952 Plymouth Cranbrook "Rican" (my grandfathers) 1931 Ford Model A Coupe "Black Beauty" 1930 Ford Model A truck "Club Cab" 4x4 Rottenwood Garage and Speed Shop.....where everything must be racy! *It's not just a hobby..It's a LIFESTYLE!!!* Thanks for nothing Barrett-Jackson You cant fix stupid or teach accountability! Time wasters, looky Lous and tire kickers are everywhere!

01-28-2011, 09:35 PM	#33
Old School Kid Rottenwood Garage Member..Yes! Join Date: Oct 2008 Location: Marietta, Georgia Posts: 174	Re: Project "RACE TRUCK" aka "Last of the spare parts" build Great... Thanks Zeke's Garage for the simple to the point information..... That's what I was looking for I like BBQ! ( Need to post in GA section!) __________________ When interests become diversified, not all can be Barrett Jackson. Budgets and Accountants get in the way. My 65 (SOLD) http://67-72chevytrucks.com/vboard/s...d.php?t=317013 My 51 (SOLD) http://67-72chevytrucks.com/vboard/s...80#post3551880 Racetruck III (SOLD) http://67-72chevytrucks.com/vboard/s...72#post4254972 Rottenwood Garage and Speed Shop.....where everything must be racy! Gone to dark side for a while...1966 F100 in the stable

01-29-2011, 06:19 PM	#34
72freak Rottenwood Garage Member Join Date: May 2005 Location: Marietta, Georgia Posts: 4,321	Re: Project "RACE TRUCK" aka "Last of the spare parts" build She got her powerplant today!!!! RACE MOTOR!!! Now we need the T5 Attached Images __________________ 2004 Chevrolet Suburban C1500 2001 Chevrolet 2500HD Crew 6.0 1999 Harley Davidson Electra Glide 1972 Chevrolet C-20 Custom Camper "Dump Truck" 1972 Chevrolet C-20 Suburban "Big Green" 1969 Chevrolet C-50 Wedge Hauler "Leonidis" 1966 C-10 2x4 short fleet 327 4 speed "Race Truck" 1952 Plymouth Cranbrook "Rican" (my grandfathers) 1931 Ford Model A Coupe "Black Beauty" 1930 Ford Model A truck "Club Cab" 4x4 Rottenwood Garage and Speed Shop.....where everything must be racy! *It's not just a hobby..It's a LIFESTYLE!!!* Thanks for nothing Barrett-Jackson You cant fix stupid or teach accountability! Time wasters, looky Lous and tire kickers are everywhere! Last edited by 72freak; 01-29-2011 at 06:19 PM.

01-30-2011, 09:33 AM	#35
Old School Kid Rottenwood Garage Member..Yes! Join Date: Oct 2008 Location: Marietta, Georgia Posts: 174	Re: Project "RACE TRUCK" aka "Last of the spare parts" build One mans "Poo Poo" is another mans "Race Motor"! Thanks 72freak for some greasy fun... __________________ When interests become diversified, not all can be Barrett Jackson. Budgets and Accountants get in the way. My 65 (SOLD) http://67-72chevytrucks.com/vboard/s...d.php?t=317013 My 51 (SOLD) http://67-72chevytrucks.com/vboard/s...80#post3551880 Racetruck III (SOLD) http://67-72chevytrucks.com/vboard/s...72#post4254972 Rottenwood Garage and Speed Shop.....where everything must be racy! Gone to dark side for a while...1966 F100 in the stable

02-09-2011, 06:13 AM	#36
72freak Rottenwood Garage Member Join Date: May 2005 Location: Marietta, Georgia Posts: 4,321	Re: Project "RACE TRUCK" aka "Last of the spare parts" build Still waiting on the T5, electric water pump, electric fuel pump, gear driven timing chain, split header, dual carb manifold and blower. Come on "Old School" it cant be a race truck withough it! Have you given any thought to some nitros? __________________ 2004 Chevrolet Suburban C1500 2001 Chevrolet 2500HD Crew 6.0 1999 Harley Davidson Electra Glide 1972 Chevrolet C-20 Custom Camper "Dump Truck" 1972 Chevrolet C-20 Suburban "Big Green" 1969 Chevrolet C-50 Wedge Hauler "Leonidis" 1966 C-10 2x4 short fleet 327 4 speed "Race Truck" 1952 Plymouth Cranbrook "Rican" (my grandfathers) 1931 Ford Model A Coupe "Black Beauty" 1930 Ford Model A truck "Club Cab" 4x4 Rottenwood Garage and Speed Shop.....where everything must be racy! *It's not just a hobby..It's a LIFESTYLE!!!* Thanks for nothing Barrett-Jackson You cant fix stupid or teach accountability! Time wasters, looky Lous and tire kickers are everywhere! Last edited by 72freak; 02-09-2011 at 06:15 AM.

02-15-2011, 10:22 PM	#37
72freak Rottenwood Garage Member Join Date: May 2005 Location: Marietta, Georgia Posts: 4,321	Re: Project "RACE TRUCK" aka "Last of the spare parts" build We did some special race modifications today to the engine and we should have the transmission strapped to it and drive shaft in by the end of the week. __________________ 2004 Chevrolet Suburban C1500 2001 Chevrolet 2500HD Crew 6.0 1999 Harley Davidson Electra Glide 1972 Chevrolet C-20 Custom Camper "Dump Truck" 1972 Chevrolet C-20 Suburban "Big Green" 1969 Chevrolet C-50 Wedge Hauler "Leonidis" 1966 C-10 2x4 short fleet 327 4 speed "Race Truck" 1952 Plymouth Cranbrook "Rican" (my grandfathers) 1931 Ford Model A Coupe "Black Beauty" 1930 Ford Model A truck "Club Cab" 4x4 Rottenwood Garage and Speed Shop.....where everything must be racy! *It's not just a hobby..It's a LIFESTYLE!!!* Thanks for nothing Barrett-Jackson You cant fix stupid or teach accountability! Time wasters, looky Lous and tire kickers are everywhere!

02-15-2011, 10:30 PM	#38
Old School Kid Rottenwood Garage Member..Yes! Join Date: Oct 2008 Location: Marietta, Georgia Posts: 174	Re: Project "RACE TRUCK" aka "Last of the spare parts" build yesssssssssss! __________________ When interests become diversified, not all can be Barrett Jackson. Budgets and Accountants get in the way. My 65 (SOLD) http://67-72chevytrucks.com/vboard/s...d.php?t=317013 My 51 (SOLD) http://67-72chevytrucks.com/vboard/s...80#post3551880 Racetruck III (SOLD) http://67-72chevytrucks.com/vboard/s...72#post4254972 Rottenwood Garage and Speed Shop.....where everything must be racy! Gone to dark side for a while...1966 F100 in the stable

02-15-2011, 11:35 PM	#39
quickstrikez06 Registered User Join Date: Feb 2011 Location: goldsboro, nc Posts: 14	Re: Project "RACE TRUCK" aka "Last of the spare parts" build Hey guys... My truck is currently in Snellville. In the middle of Gwinnett. Im looking for someone that can take the body off and do a tear down, clean, and suspension rebuild. You guys have someone you can recommend? My thread is on here... Its called Dads old 72. http://67-72chevytrucks.com/vboard/s...d.php?t=446960 Its got a 307 in it and Im looking to get rid of it, the cab, the tranny, and rear end.

02-19-2011, 10:05 PM	#42
72freak Rottenwood Garage Member Join Date: May 2005 Location: Marietta, Georgia Posts: 4,321	Re: Project "RACE TRUCK" aka "Last of the spare parts" build Engine, clutch, transmission and shifter are all mounted. Driveshaft and cab to come soon! It gets racier every day!!! Attached Images __________________ 2004 Chevrolet Suburban C1500 2001 Chevrolet 2500HD Crew 6.0 1999 Harley Davidson Electra Glide 1972 Chevrolet C-20 Custom Camper "Dump Truck" 1972 Chevrolet C-20 Suburban "Big Green" 1969 Chevrolet C-50 Wedge Hauler "Leonidis" 1966 C-10 2x4 short fleet 327 4 speed "Race Truck" 1952 Plymouth Cranbrook "Rican" (my grandfathers) 1931 Ford Model A Coupe "Black Beauty" 1930 Ford Model A truck "Club Cab" 4x4 Rottenwood Garage and Speed Shop.....where everything must be racy! *It's not just a hobby..It's a LIFESTYLE!!!* Thanks for nothing Barrett-Jackson You cant fix stupid or teach accountability! Time wasters, looky Lous and tire kickers are everywhere!



Register or Log In To remove these advertisements.

02-20-2011, 01:41 PM	#43
OrangeCrush1970 Registered User Join Date: Jun 2007 Location: Smyrna, GA Posts: 709	Re: Project "RACE TRUCK" aka "Last of the spare parts" build That "popping Noise" when we were pushing it was my ankle!!! __________________ *Rottenwood Garage* 1970...71...72 C1500 aka Orange aka Sideshow Bob 540 BB Straub Roller Cam, AFR Magnums, XP 950, TKO 600 2 Tons of Fun

02-24-2011, 07:52 AM	#44
72freak Rottenwood Garage Member Join Date: May 2005 Location: Marietta, Georgia Posts: 4,321	Re: Project "RACE TRUCK" aka "Last of the spare parts" build Big weekend to come.....going to get a cab and possibly some wiring! Racier every day! __________________ 2004 Chevrolet Suburban C1500 2001 Chevrolet 2500HD Crew 6.0 1999 Harley Davidson Electra Glide 1972 Chevrolet C-20 Custom Camper "Dump Truck" 1972 Chevrolet C-20 Suburban "Big Green" 1969 Chevrolet C-50 Wedge Hauler "Leonidis" 1966 C-10 2x4 short fleet 327 4 speed "Race Truck" 1952 Plymouth Cranbrook "Rican" (my grandfathers) 1931 Ford Model A Coupe "Black Beauty" 1930 Ford Model A truck "Club Cab" 4x4 Rottenwood Garage and Speed Shop.....where everything must be racy! *It's not just a hobby..It's a LIFESTYLE!!!* Thanks for nothing Barrett-Jackson You cant fix stupid or teach accountability! Time wasters, looky Lous and tire kickers are everywhere!

02-26-2011, 05:29 PM	#45
72freak Rottenwood Garage Member Join Date: May 2005 Location: Marietta, Georgia Posts: 4,321	Re: Project "RACE TRUCK" aka "Last of the spare parts" build She got a cab, some fresh brake lines and a new master cylinder today along with some rattle can brown RACE paint! Check out that RACE EXHAUST!!! Attached Images __________________ 2004 Chevrolet Suburban C1500 2001 Chevrolet 2500HD Crew 6.0 1999 Harley Davidson Electra Glide 1972 Chevrolet C-20 Custom Camper "Dump Truck" 1972 Chevrolet C-20 Suburban "Big Green" 1969 Chevrolet C-50 Wedge Hauler "Leonidis" 1966 C-10 2x4 short fleet 327 4 speed "Race Truck" 1952 Plymouth Cranbrook "Rican" (my grandfathers) 1931 Ford Model A Coupe "Black Beauty" 1930 Ford Model A truck "Club Cab" 4x4 Rottenwood Garage and Speed Shop.....where everything must be racy! *It's not just a hobby..It's a LIFESTYLE!!!* Thanks for nothing Barrett-Jackson You cant fix stupid or teach accountability! Time wasters, looky Lous and tire kickers are everywhere!

02-26-2011, 05:34 PM	#46
67chevy1series Registered User Join Date: Mar 2010 Location: a t w a t e r cali 95301 Posts: 10,713	Re: Project "RACE TRUCK" aka "Last of the spare parts" build lookin good! now you just need the front clip on!

02-26-2011, 07:13 PM	#48
OrangeCrush1970 Registered User Join Date: Jun 2007 Location: Smyrna, GA Posts: 709	Re: Project "RACE TRUCK" aka "Last of the spare parts" build What is that ORANGE thing looming in the background???? Could that be.....another race truck!?!?! Looking good! __________________ *Rottenwood Garage* 1970...71...72 C1500 aka Orange aka Sideshow Bob 540 BB Straub Roller Cam, AFR Magnums, XP 950, TKO 600 2 Tons of Fun

02-26-2011, 07:43 PM	#49
68steppsidee Registered User Join Date: Oct 2010 Location: Knoxville, TN Posts: 196	Re: Project "RACE TRUCK" aka "Last of the spare parts" build Where'd the stepside bed go? Last edited by VA72C10; 02-26-2011 at 08:10 PM. Reason: WTB not allowed in build threads and You must be a supporting member to post WTB, WIW, or FS items.

02-26-2011, 08:49 PM	#50
JasonBird '67 C-10 LWB Driver Join Date: Dec 2010 Location: Andover, Kansas Posts: 380	Re: Project "RACE TRUCK" aka "Last of the spare parts" build where's the parachute go? maybe it's in the mail... __________________ '67 C-10 LWB - My Build Thread '67 C-20 LWB - My Donor/ Parts truck - SOLD! '92 GMC SAFARI VAN - My Parts Go Getter '06 KIA SPORTAGE EX - My Commuter "All of this crap better make a truck!" - my wife Sue. Proud U.S.M.C. Dad!

Thread Tools
Show Printable Version Email this Page
Display Modes
Linear Mode Switch to Hybrid Mode Switch to Threaded Mode

Register or Log In To remove these advertisements.