TN Cab Pieces/Parts

[Mikes66ChevyC10]

Originally Posted by DPowers

So a section like this is what you need?

Yep looks good to me.

[DPowers]

Originally Posted by niterider65

if your going to cut up the cab i need the right side cab corner if its not bondo all up
and if it could be over cut so i can drill out the spot welds on the rocker side and cut out just past the first circle in the back of the cab if its not taken
just let me know how much shipped to 76107
..

Is this the section that you need?

[DPowers]

Originally Posted by 62jimmy

If any good I would be interested in the front half of the passenger outer rocker panel it you decide to dice it up, thanks, jeremy

Can you get me a pic of the exact area you are talking about and i can check.

[DPowers]

Originally Posted by Mikes66ChevyC10

Yep looks good to me.

Ok I will cut it out. How would $15 plus whatever shipping would be?

[Mikes66ChevyC10]

Originally Posted by DPowers

Ok I will cut it out. How would $15 plus whatever shipping would be?

Sounds good to me. Thanks again for doing this. This spot is the last area of rust on the cab that needs to be fixed then all the rust repair is done!

[DPowers]

no problem. will keep you posted

[niterider65]

Originally Posted by DPowers

Is this the section that you need?

That will work
Thanks

[niterider65]

Originally Posted by niterider65

if your going to cut up the cab i need the right side cab corner if its not bondo all up
and if it could be over cut so i can drill out the spot welds on the rocker side and cut out just past the first circle in the back of the cab if its not taken
just let me know how much shipped to 76107
..

just let me know how much
Thanks

[DPowers]

Originally Posted by niterider65

just let me know how much
Thanks

How's $20.00 plus whatever shipping is?

[62jimmy]

This part of the rocker is what im looking at. As you can see mine is smashed flat up against the cab, I was hoping for a piece about mid door forward that included the plug hole in the front.

[LostMy65]

Originally Posted by LostMy65

I need two of these cab mounting washers:

I only need the washer with the cupping. The washer in the square cut area there. I need two of them.

[DPowers]

Originally Posted by 62jimmy

This part of the rocker is what im looking at. As you can see mine is smashed flat up against the cab, I was hoping for a piece about mid door forward that included the plug hole in the front.

this work?

[aotte1]

Need two firewall pieces on both sides of the tunnel area, where BB valve covers would have dented firewall, can post photos of area needed. Is this available

L

[aotte1]

One of two firewall pieces needed, left side, would like a little larger piece, as will weld in.

L

[aotte1]

Other firewall piece needed, right side, would like a little larger piece too. Photos of patches would be nice.
L

[DPowers]

Like this whole section?

[62jimmy]

Originally Posted by DPowers

this work?

Plug end looks good to me. I would need it cut back about 14 or 15 inches into the rocker to straighten it out?

I forgot to ask is the radio hole hacked I need a repair piece for that too?

[chad64chevy]

here is a better picture! I just measured from the top bolt hole for the rear view mirror 9" each side! I need the lip the windshield an everything inside the blue tape, thanks!!

[rickoner]

I'm looking for this piece. Roughly 24" wide and up to atleast the dome light. If your's is available and solid, what would you want for it shipped to 15126?

Thanks.

[DPowers]

Originally Posted by 62jimmy

Plug end looks good to me. I would need it cut back about 14 or 15 inches into the rocker to straighten it out?

I forgot to ask is the radio hole hacked I need a repair piece for that too?

Radio is hacked if I remember right.
How about $10.00 plus whatever shipping would be for the rocker piece?

[DPowers]

Originally Posted by rickoner

I'm looking for this piece. Roughly 24" wide and up to atleast the dome light. If your's is available and solid, what would you want for it shipped to 15126?

Thanks.

I will have to remove the rear window to get that piece. How about $15.00 plus whatever shipping would be?

[DPowers]

Originally Posted by chad64chevy

here is a better picture! I just measured from the top bolt hole for the rear view mirror 9" each side! I need the lip the windshield an everything inside the blue tape, thanks!!

Will have to remove windshield to get that piece. $20.00 plus shipping work?

[chad64chevy]

that will work, can you get pics of the back side after cutting it out, please

[aotte1]

"Like this whole section?"

That will work, needs to be a few inches out on the flat face of firewall. or you could do two small pieces. what ever is easy for you. I will install it by replacing two smaller pieces.

[DPowers]

Alright will see what I can do $20.00 plus shipping? I have a son that lives in Louisville and if he comes down for Christmas and I can get it cut out in time, I can see if can send it back with him, but will keep you posted.