MD Suburban metal cuts

[71blksuper4x4]

What is circled in red Richard....needing the last 3-4" of roof from drip rail flange to 1/2" above body line. Need around 40" of length.

[richard2717]

I really don't know why I am being so dense on this, I just keep looking at the pic you posted and it looks like you need the part i have the yellow arrow at. Or is that what you were trying to cut and went too high into the roof half?


.

[richard2717]

I think i am going to go lay down and revisit it in the morning.

[71blksuper4x4]

Hey Richard, this is what I am trying to fill in. This should explain I need the drip rail flange on the roof that gets spot welded to the drip railing. Then I am asking you to cut it just above the extra body line that a Burb roof has. I burnt through one of mine when I was trying to remove it.

[richard2717]

Josh
$75 shipped for both pcs

.

[richard2717]

Trevor,
I am understanding what you need. I will get it cut out later today. $25 plus shipping. Not sure if I still have your address but should be able to locate on PP

Richard

[richard2717]

Originally Posted by 71blksuper4x4

Hey Richard, this is what I am trying to fill in. This should explain I need the drip rail flange on the roof that gets spot welded to the drip railing. Then I am asking you to cut it just above the extra body line that a Burb roof has. I burnt through one of mine when I was trying to remove it.

Trevor
Here is what I cut out. I unbolted it from the lower half. The pc is just shy of 48" just bc it made no difference in the shipping cost from 40''. anything longer than 48'' and the cost almost doubled being over sized. If I did not cut it correctly I still have the entire driver side to try again lol. $55 shipped if it is correct. PP in my sig below

Thanks

.

[71blksuper4x4]

Originally Posted by richard2717

Trevor
Here is what I cut out. I unbolted it from the lower half. The pc is just shy of 48" just bc it made no difference in the shipping cost from 40''. anything longer than 48'' and the cost almost doubled being over sized. If I did not cut it correctly I still have the entire driver side to try again lol. $55 shipped if it is correct. PP in my sig below

Thanks

.

Perfect Richard, PayPal sent. Thanks again, Trevor

[richard2717]

Got it and it will ship in the morning as well. Thanks

[71blksuper4x4]

Thanks Richard, I got the piece yesterday. Looks great. Trevor

[71blksuper4x4]

Richard did you end up scrapping these out? Trevor

[richard2717]

Originally Posted by 71blksuper4x4

Richard did you end up scrapping these out? Trevor

I still have quite a bit

[71blksuper4x4]

Richard, I may be needing a 8-10” piece of inner pillar off a driver’s inner b pillar. I’ll let you know tomorrow.

[richard2717]

Originally Posted by 71blksuper4x4

Richard, I may be needing a 8-10” piece of inner pillar off a driver’s inner b pillar. I’ll let you know tomorrow.

here is pics of what is left both have been cut pretty much flush at the front of them heading towards the A pillar

.

[71blksuper4x4]

Actually Richard, those are perfect for me. I am working on finishing my inner roof and need pieces to transition from the pillars to the I need roof as shown. Before I finish welding and grinding, I wanted to get a game plan.

[richard2717]

So you basically only need the inner metal overlay like I have boxed here, or do you need the entire thickness of it all the way to the outside roof?

DO you need any of the horizontal cover above the doors?

.

[71blksuper4x4]

Basically, that is all I need Richard. I do not need any of the pieces above the door. I already have my whole inner roof mocked up other than finishing it out and these pieces. If you can cut out both of those for me as I need two for each side. Maybe 3" inches below the door weatherstrip channel intersection but above the shoulder harness hole. Thanks Trevor

[shume]

Looking for drivers side rear frame section from axle crossmember to bumper. I need it for a Blazer. If you have one from Suburban hoping it might work.

[richard2717]

The tail end of the suburban is different from the 72' Blazers. Here are a couple pictures to show the difference. If your Blazer is 69-71 the frame just cuts off flat at the rear but I do not have one here to verify if they are indeed swapable.

1st picture shows suburban tail end



2nd pic shows how the blazer turns down a lot sharper. This frame is not for sale. You might check with 1Rippen6 he usually has some blazer stuff

[shume]

Thanks. With the turn down on Blazer not sure I could make the Suburban piece work.

[71blksuper4x4]

Hey Richard, these would work.

[kev2809]

are ya still parting these out? i need this section, its driver side back wheel arch area.. piece i used did not have the wheel arch indention..

[richard2717]

Originally Posted by kev2809

are ya still parting these out? i need this section, its driver side back wheel arch area.. piece i used did not have the wheel arch indention..

Missed this with the holidays. I do not have ant good lower metal, everything is rusty or totally gone

[kev2809]

Originally Posted by richard2717

Missed this with the holidays. I do not have ant good lower metal, everything is rusty or totally gone

ok thanks for checkin!

[ajgriffin]

I see you said you don't have any good lower metal, what about the driver's rear wheel well? I need a small section at the front, 4" up and 3" toward the rear to include the corner.



I can take a better picture with tape on the wheel well if it would communicate better. This is the area I'm trying to patch.