Project: Bad Bagged '68.5 - Page 4 - The 1947 - Present Chevrolet & GMC Truck Message Board Network

67Fleet · 03-25-2007, 08:03 AM

Jared, I'm definitely interested in seeing pics of that as I'm getting ready to put my 1.5" sectioned crossmember in my 67.

jlaird · 03-25-2007, 08:12 AM

Quote:

Originally Posted by Jaredm82

Thats what I did. My crossmember is sectioned 1.75" and thats how much I moved all my steering up. We just basically sliced the side off the frame off and raised it 1.75" and welded it back together. Then reinforced the crap out of it!!! I can maybe get pictures tomorrow when Im working on my truck...

If you could get pictures that would be great. I looked at raising the steering box and all but the problem I saw was the pitman arm and idler arm hitting the bottom of the frame when your fully turned. Are you notching for this or raising the entire section of the frame for clearance. I guess a pic would show it best.

FRENCHBLUE72 · 03-25-2007, 10:09 AM

Im gonna use this set-up for mine.

jlaird · 03-25-2007, 04:12 PM

Quote:

Originally Posted by FRENCHBLUE72

Im gonna use this set-up for mine.

Yea, the steering linkage is the easy part. We are all mainly concerned with the tie rods, idler arm, pitman arm, etc...

XXL · 03-26-2007, 12:24 PM

Quote:

Originally Posted by FRENCHBLUE72

Im gonna use this set-up for mine.

Hey, don't use that set-up... I need it to steer my truck!

jlaird · 03-26-2007, 01:08 PM

hey XXL, how much is your crossmember sectioned? Do you have pics of the steering clearance "problem areas"?

Jaredm82 · 03-26-2007, 01:36 PM

I am going out to work on my truck right now. I will get some pics for you guys in a bit..

Jaredm82 · 03-26-2007, 05:33 PM

Here are f ew pictures of my steering set up. Worked great for a few thousand miles already accept for the steering shaft. It used to have a rag joint but I have since replaced it with a second u joint. My crossmember is sectioned 1.75" and my steering is raised 1.75" as well. I also lowered my cab mounts 1". The tilt column is out of an early 70's gm van and I raised it up as much as I could by cutting into the firewall. Everything works well and there are no signs of cracking...

XXL · 03-26-2007, 05:50 PM

Quote:

Originally Posted by jlaird

hey XXL, how much is your crossmember sectioned? Do you have pics of the steering clearance "problem areas"?

1.5" section. There was only small clearance issue... see pics here.

smbrouss70 · 03-26-2007, 06:21 PM

XXL or anyone else who has done this crossmember mod, have you noticed any negative (or positive) effects on the bump steer? Jared, I'm sure yours is the same as before since you raised your linkage also.

FRENCHBLUE72 · 03-26-2007, 06:50 PM

Quote:

Originally Posted by XXL

Hey, don't use that set-up... I need it to steer my truck!

ken you better check you ride I think you maybe missing some parts.

FRENCHBLUE72 · 03-26-2007, 06:52 PM

I should have the steering linkage on tonight.

jlaird · 03-26-2007, 07:00 PM

Quote:

Originally Posted by XXL

1.5" section. There was only small clearance issue... see pics here.

I hope that is the case with me. I'm just preparing myself for the worst.

Jared, thanks for the pics. Makes sense now.

Josh

jlaird · 03-26-2007, 07:26 PM

XXL, did you have "less" problems because you have tubulars?? Hmmmm

jlaird · 03-26-2007, 08:48 PM

OK, something else to throw into the equation. Porterbuilt moved the centerline of the front suspension forward one inch to center the tire in the wheelwell. Has anybody reinstalled their stock crossmeber forward one inch?

7deuce · 03-26-2007, 08:55 PM

I did mine 1 1/8 and I still had the problems that XXL is talking about. My bump steer is bad with out a sway bar. And there was some grinding on the X-member and steering components.

Jaredm82 · 03-26-2007, 08:58 PM

oh ya, I moved my motor up and forward, I dont remember how much though...

FRENCHBLUE72 · 03-26-2007, 10:20 PM

Looks like I have some grinding to do not bad though..

jlaird · 04-25-2007, 09:24 PM

Finished my lower control arm mod. Came out really nice. Here are some pics of each step.

XXL · 04-25-2007, 09:32 PM

Quote:

Originally Posted by jlaird

You're going to want to reinforce that cardboard. Maybe some duct tape?

jlaird · 04-25-2007, 10:14 PM

Quote:

Originally Posted by XXL

You're going to want to reinforce that cardboard. Maybe some duct tape?

We can always count on you for those helpful comments!!! LOL!

pissonNOS · 04-26-2007, 12:33 AM

just wondering what the advantage of this was? does it distibute the force better than just welding a cup into your cut hole?

PBFAB.COM · 04-26-2007, 01:42 AM

Looks like the bag will sit a little lower and not rub on the control arm.

jlaird · 04-26-2007, 08:15 AM

Quote:

Originally Posted by porterbuilt

Looks like the bag will sit a little lower and not rub on the control arm.

exactly.

XXL · 04-26-2007, 09:19 AM

Quote:

Originally Posted by jlaird

We can always count on you for those helpful comments!!! LOL!

4000+ posts and counting. Just think of all the help that's provided others *cough cough*

Arms look good, btw!

03-25-2007, 08:03 AM	#76
67Fleet Outlandish Trends - FL Join Date: Jul 2005 Location: Orlando Posts: 1,396	Re: progress pics Jared, I'm definitely interested in seeing pics of that as I'm getting ready to put my 1.5" sectioned crossmember in my 67. __________________ -Bret 67 short-fleet sold!

03-25-2007, 10:09 AM	#78
FRENCHBLUE72 PROJECT 7DEUCE Join Date: Dec 2002 Location: GRANTS PASS OR Posts: 21,606	Re: progress pics Im gonna use this set-up for mine. Attached Images __________________ GO BIG GREEN GO DUCKS MEMBER #6377 72 k-5 daily driver 6'' lift 35'' 350-350-205 slowly getting rust free. Project "7DEUCE" check out my build http://67-72chevytrucks.com/vboard/s...d.php?t=267665 Tim Powell..R.I.P EastSideLowlife..... R.I.P..

03-26-2007, 01:08 PM	#81
jlaird Senior Member Join Date: May 2004 Location: johnstown, NY Posts: 2,393	Re: progress pics hey XXL, how much is your crossmember sectioned? Do you have pics of the steering clearance "problem areas"?

03-26-2007, 01:36 PM	#82
Jaredm82 Active Member Join Date: Jul 2005 Location: Ca Posts: 211	Re: progress pics I am going out to work on my truck right now. I will get some pics for you guys in a bit..

03-26-2007, 05:33 PM	#83
Jaredm82 Active Member Join Date: Jul 2005 Location: Ca Posts: 211	Re: progress pics Here are f ew pictures of my steering set up. Worked great for a few thousand miles already accept for the steering shaft. It used to have a rag joint but I have since replaced it with a second u joint. My crossmember is sectioned 1.75" and my steering is raised 1.75" as well. I also lowered my cab mounts 1". The tilt column is out of an early 70's gm van and I raised it up as much as I could by cutting into the firewall. Everything works well and there are no signs of cracking...

03-26-2007, 06:21 PM	#85
smbrouss70 Registered User Join Date: Sep 2003 Location: Rayne, LA Posts: 2,781	Re: progress pics XXL or anyone else who has done this crossmember mod, have you noticed any negative (or positive) effects on the bump steer? Jared, I'm sure yours is the same as before since you raised your linkage also. __________________ Steven "If dogs don't go to heaven, when I die I want to go wherever they went." -- Will Rogers R.I.P. Oscar R.I.P. Ratchet 1967 Pontiac GTO - Dad was the Original Owner 1970 Chevy 2wd SWB "Oscar's Truck" 1970 Chevy 2wd Blazer "Ratchet's Blazer" 2013 Chevy 2500HD Crew Cab Duramax/Allison Z71 LTZ "Brown Sugar" 2017 Chevy Suburban "BDB" 2020 Chevy Blazer Premier "Foxy" Member of Louisiana Classic Truck Club (LCTC) Shop Build

03-26-2007, 06:52 PM	#87
FRENCHBLUE72 PROJECT 7DEUCE Join Date: Dec 2002 Location: GRANTS PASS OR Posts: 21,606	Re: progress pics I should have the steering linkage on tonight. __________________ GO BIG GREEN GO DUCKS MEMBER #6377 72 k-5 daily driver 6'' lift 35'' 350-350-205 slowly getting rust free. Project "7DEUCE" check out my build http://67-72chevytrucks.com/vboard/s...d.php?t=267665 Tim Powell..R.I.P EastSideLowlife..... R.I.P..

03-26-2007, 07:26 PM	#89
jlaird Senior Member Join Date: May 2004 Location: johnstown, NY Posts: 2,393	Re: progress pics XXL, did you have "less" problems because you have tubulars?? Hmmmm

03-26-2007, 08:48 PM	#90
jlaird Senior Member Join Date: May 2004 Location: johnstown, NY Posts: 2,393	Re: progress pics OK, something else to throw into the equation. Porterbuilt moved the centerline of the front suspension forward one inch to center the tire in the wheelwell. Has anybody reinstalled their stock crossmeber forward one inch?

03-26-2007, 08:55 PM	#91
7deuce Sold! 2 days after finished Join Date: Oct 2005 Location: Ohio Posts: 327	Re: progress pics I did mine 1 1/8 and I still had the problems that XXL is talking about. My bump steer is bad with out a sway bar. And there was some grinding on the X-member and steering components.

03-26-2007, 08:58 PM	#92
Jaredm82 Active Member Join Date: Jul 2005 Location: Ca Posts: 211	Re: progress pics oh ya, I moved my motor up and forward, I dont remember how much though...

03-26-2007, 10:20 PM	#93
FRENCHBLUE72 PROJECT 7DEUCE Join Date: Dec 2002 Location: GRANTS PASS OR Posts: 21,606	Re: progress pics Looks like I have some grinding to do not bad though.. __________________ GO BIG GREEN GO DUCKS MEMBER #6377 72 k-5 daily driver 6'' lift 35'' 350-350-205 slowly getting rust free. Project "7DEUCE" check out my build http://67-72chevytrucks.com/vboard/s...d.php?t=267665 Tim Powell..R.I.P EastSideLowlife..... R.I.P..

04-25-2007, 09:24 PM	#94
jlaird Senior Member Join Date: May 2004 Location: johnstown, NY Posts: 2,393	Re: progress pics Finished my lower control arm mod. Came out really nice. Here are some pics of each step.

04-26-2007, 12:33 AM	#97
pissonNOS senior member Join Date: Feb 2003 Location: fort macleod alberta Posts: 2,770	Re: progress pics just wondering what the advantage of this was? does it distibute the force better than just welding a cup into your cut hole? __________________ 69 GMC bagged

04-26-2007, 01:42 AM	#98
PBFAB.COM Senior Member Join Date: Dec 2003 Location: Mesa,Az Posts: 3,981	Re: progress pics Looks like the bag will sit a little lower and not rub on the control arm. __________________ www.PorterbuiltFabrication.com Phone: 480-297-2621 E-mail: sales@pbfab.com Find us on FaceBook under Porterbuilt Fabrication Specializing in Chassis and Suspension Components for your Classic Chevrolet Truck. We offer components from the following manufacturers: Porterbuilt Accuair Ridetech (Air Ride Technologies) Air Lift Wilwood Intro Unisteer ECE Gotta Show Air Lift Borgeson CPP Supporting this forum since 2003!



Register or Log In To remove these advertisements.

Thread Tools
Show Printable Version Email this Page
Display Modes
Linear Mode Switch to Hybrid Mode Switch to Threaded Mode

Register or Log In To remove these advertisements.