Sacto67 Build diary - Page 4 - The 1947 - Present Chevrolet & GMC Truck Message Board Network

Hardesty454 · 02-26-2013, 12:00 AM

good work so far. I understand the whole frusteration thing. Keep with it and dont expect it all to happen over night. Keep up the good work.

sacto67 · 03-05-2013, 09:53 PM

I disassembled the engine and repainted the block today. I cleaned up most of the brackets, alternator, and reassembled it. I still have to clean up the power steering pump and brackets. The a/c condenser and brackets will probably be put on hold until I figure out when/if I'm going to put a/c in the truck.

Tx Firefighter · 03-05-2013, 10:12 PM

Hey brother, FYI, I'm 99 percent sure your old six cylinder is a 250 not a 292. I don't see the big coolant bypass hose off the front of the head that 292s have. Also, 250s have six inch tall side covers, 292s have nine inch tall side covers.

Not really pertinent in light of the small block you just posted a pic of, but thought I'd throw that in about the old engine.
Posted via Mobile Device

sacto67 · 03-05-2013, 10:32 PM

Quote:

Originally Posted by Tx Firefighter

Hey brother, FYI, I'm 99 percent sure your old six cylinder is a 250 not a 292. I don't see the big coolant bypass hose off the front of the head that 292s have. Also, 250s have six inch tall side covers, 292s have nine inch tall side covers.

Not really pertinent in light of the small block you just posted a pic of, but thought I'd throw that in about the old engine.
Posted via Mobile Device

Thanks, it is a 250, I was told originally it was a 292.

sacto67 · 03-08-2013, 12:54 PM

I need a little help here. I've try to search and haven't found the answer on the forum. So I've got the 84 cross member in and I'm planning on using the 84 v8 perches. Here's what I've got, if I bolt the bottom bolts on the perches to the cross member where they originally were the perches have a gap between the frame and the perch on the top side. The gap is about 1/4". From what I can see my two choices are to leave the bottoms and build a spacer plate to fill the gap or bolt the upper perch on the frame and re-drill the lower holes in the cross member. What do people usually do??

Hardesty454 · 03-08-2013, 01:05 PM

I'd like to see a pic. But off hand I would fill and re drill from the sounds of it.
Posted via Mobile Device

sacto67 · 03-08-2013, 01:09 PM

Quote:

Originally Posted by Hardesty454

I'd like to see a pic. But off hand I would fill and re drill from the sounds of it.
Posted via Mobile Device

Pic added, thanks. Ultimately I'll bolt the perches to the motor and set it in to see where they sit, but I've got a few days until I can work on it again and figured I'd try to figure out how it is usually done.

Low Elco · 03-08-2013, 01:45 PM

Diggin' this already! I have no idea on the mounts, PM lolife99. if he don't know, don't nobody know. Dig your little beater truck!

shawno72 · 03-08-2013, 01:51 PM

Looking real good

sacto67 · 03-08-2013, 02:28 PM

Thanks! I shot him a PM.

SLOW POKE · 03-08-2013, 02:39 PM

Sweet Truck, Mine is an ex military brat too. Army National Guard though....

**lolife99** · 03-08-2013, 03:34 PM

You are headed in the right direction.
Make a spacer plate for the top of the frame.

73-87 frames are taller than the 67-72 frames.

sacto67 · 03-08-2013, 05:52 PM

Quote:

Originally Posted by lolife99

You are headed in the right direction.
Make a spacer plate for the top of the frame.

73-87 frames are taller than the 67-72 frames.

Cool thanks!

sacto67 · 03-10-2013, 11:51 PM

Pulled the bed off today for two reasons, 1st I was just ready to pull it, and 2nd because I finally got a letter from my home owners association complaining about my "dilapidated inoperable truck" the in my driveway. So tomorrow it's moving to the side of the house.

Low Elco · 03-11-2013, 08:18 AM

Is that a Ferrari peeking out? Or am I just a dummy?

sacto67 · 03-11-2013, 01:21 PM

Quote:

Originally Posted by Low Elco

Is that a Ferrari peeking out? Or am I just a dummy?

Hahaha you're not a dummy...... But it's only a replica.

sacto67 · 07-16-2013, 01:24 AM

No real progress on the truck, but I did get my new, free, bed sides home. I don't know when I'll get time to cut it down to a short bed, but it'll happen.

sacto67 · 07-23-2013, 01:16 AM

I've gotten together some parts for an idea I have. This is a mixture of new Chevy, Honda, and BMW.

The idea is for a new style emblem for the front fenders. New chevy is the bowtie from a SSR, Honda is the "I" and "O" from a new Pilot, and BMW is the idea of an amber light behind the emblem as a park/turn light. A buddy is woring on the amber backlight which I haven't gotten yet, but here is the bowtie and "10".

Hardesty454 · 07-23-2013, 10:04 AM

Well that's slick... Cool idea
Posted via Mobile Device

**Ol Blue K20** · 07-23-2013, 12:31 PM

Quote:

Originally Posted by Hardesty454

Well that's slick... Cool idea
Posted via Mobile Device

x2 looks good and the light sounds cool

Saclandman · 07-23-2013, 05:17 PM

Just found this thread. Nice find. Glad to see it coming together.

craig7070 · 07-23-2013, 07:11 PM

Im in roseville...Where are all you sacramento guys at? Im new to the thread and love learning everything about these truck..

Saclandman · 07-23-2013, 07:21 PM

I'm in Natomas and my truck is up in Shingle Springs.
Posted via Mobile Device

sacto67 · 07-23-2013, 07:47 PM

I'm near Rancho Cordova.

Rich916 · 07-23-2013, 09:33 PM

I've seen that emblem, it's definetly top notch bling!

02-26-2013, 12:00 AM	#76
Hardesty454 Registered User Join Date: Feb 2011 Location: Riverbank, Ca Posts: 1,006	Re: Sacto67 Build diary good work so far. I understand the whole frusteration thing. Keep with it and dont expect it all to happen over night. Keep up the good work. __________________ Rob 1971 c10 - ground up in progress Tripp's Speed Shop Build - http://67-72chevytrucks.com/vboard/s...d.php?t=589750

03-05-2013, 09:53 PM	#77
sacto67 Registered User Join Date: Sep 2011 Location: Sacramento Posts: 196	Re: Sacto67 Build diary I disassembled the engine and repainted the block today. I cleaned up most of the brackets, alternator, and reassembled it. I still have to clean up the power steering pump and brackets. The a/c condenser and brackets will probably be put on hold until I figure out when/if I'm going to put a/c in the truck. Attached Images __________________ 1968 Chevy SWB stepside original USAF truck http://67-72chevytrucks.com/vboard/s...d.php?t=483462

03-05-2013, 10:12 PM	#78
Tx Firefighter Watch out for your cornhole ! Join Date: Jun 2003 Location: Azle, Texas Posts: 14,162	Re: Sacto67 Build diary Hey brother, FYI, I'm 99 percent sure your old six cylinder is a 250 not a 292. I don't see the big coolant bypass hose off the front of the head that 292s have. Also, 250s have six inch tall side covers, 292s have nine inch tall side covers. Not really pertinent in light of the small block you just posted a pic of, but thought I'd throw that in about the old engine. Posted via Mobile Device

03-08-2013, 12:54 PM	#80
sacto67 Registered User Join Date: Sep 2011 Location: Sacramento Posts: 196	Re: Sacto67 Build diary I need a little help here. I've try to search and haven't found the answer on the forum. So I've got the 84 cross member in and I'm planning on using the 84 v8 perches. Here's what I've got, if I bolt the bottom bolts on the perches to the cross member where they originally were the perches have a gap between the frame and the perch on the top side. The gap is about 1/4". From what I can see my two choices are to leave the bottoms and build a spacer plate to fill the gap or bolt the upper perch on the frame and re-drill the lower holes in the cross member. What do people usually do?? Attached Images __________________ 1968 Chevy SWB stepside original USAF truck http://67-72chevytrucks.com/vboard/s...d.php?t=483462 Last edited by sacto67; 03-08-2013 at 01:07 PM. Reason: Ad photo

03-08-2013, 01:05 PM	#81
Hardesty454 Registered User Join Date: Feb 2011 Location: Riverbank, Ca Posts: 1,006	Re: Sacto67 Build diary I'd like to see a pic. But off hand I would fill and re drill from the sounds of it. Posted via Mobile Device __________________ Rob 1971 c10 - ground up in progress Tripp's Speed Shop Build - http://67-72chevytrucks.com/vboard/s...d.php?t=589750

03-08-2013, 01:45 PM	#83
Low Elco Registered User Join Date: Apr 2003 Location: Indep, MO Posts: 5,893	Re: Sacto67 Build diary Diggin' this already! I have no idea on the mounts, PM lolife99. if he don't know, don't nobody know. Dig your little beater truck! __________________ Boppa's Old Yeller Truck Build, Old Yeller's New Heart! Project Buzz Bomb Flyin' Low!

03-08-2013, 01:51 PM	#84
shawno72 C/10 junkie Join Date: Nov 2010 Location: Stockton Ca Posts: 9,093	Re: Sacto67 Build diary Looking real good __________________ Shawn 70 LWB C10 current driver/project http://67-72chevytrucks.com/vboard/s...d.php?t=663051 68 SWB C10 Work in progress.....SOLD http://67-72chevytrucks.com/vboard/s...d.php?t=559520 72 LWB C10 Sold 71 LWB C10 Sold 68 LWB C10 CST Sold http://youtu.be/kbB0QrBIs9k My mom always had the best advice. It was just a tad late. After a fall that involved blood, she'd say....."Careful!"

03-08-2013, 02:28 PM	#85
sacto67 Registered User Join Date: Sep 2011 Location: Sacramento Posts: 196	Re: Sacto67 Build diary Thanks! I shot him a PM. __________________ 1968 Chevy SWB stepside original USAF truck http://67-72chevytrucks.com/vboard/s...d.php?t=483462

03-08-2013, 02:39 PM	#86
SLOW POKE Registered User Join Date: Aug 2011 Location: Texas Posts: 189	Re: Sacto67 Build diary Sweet Truck, Mine is an ex military brat too. Army National Guard though.... __________________ 68 Short step!!

03-08-2013, 03:34 PM	#87
lolife99 67-72 parts collector,… Join Date: Nov 2002 Location: Mid-MO Posts: 22,700	Re: Sacto67 Build diary You are headed in the right direction. Make a spacer plate for the top of the frame. 73-87 frames are taller than the 67-72 frames. __________________ Keith Convert to disc brakes. http://67-72chevytrucks.com/vboard/s...d.php?t=444823

03-10-2013, 11:51 PM	#89
sacto67 Registered User Join Date: Sep 2011 Location: Sacramento Posts: 196	Re: Sacto67 Build diary Pulled the bed off today for two reasons, 1st I was just ready to pull it, and 2nd because I finally got a letter from my home owners association complaining about my "dilapidated inoperable truck" the in my driveway. So tomorrow it's moving to the side of the house. Attached Images __________________ 1968 Chevy SWB stepside original USAF truck http://67-72chevytrucks.com/vboard/s...d.php?t=483462

03-11-2013, 08:18 AM	#90
Low Elco Registered User Join Date: Apr 2003 Location: Indep, MO Posts: 5,893	Re: Sacto67 Build diary Is that a Ferrari peeking out? Or am I just a dummy? __________________ Boppa's Old Yeller Truck Build, Old Yeller's New Heart! Project Buzz Bomb Flyin' Low!

07-16-2013, 01:24 AM	#92
sacto67 Registered User Join Date: Sep 2011 Location: Sacramento Posts: 196	Re: Sacto67 Build diary No real progress on the truck, but I did get my new, free, bed sides home. I don't know when I'll get time to cut it down to a short bed, but it'll happen. Attached Images __________________ 1968 Chevy SWB stepside original USAF truck http://67-72chevytrucks.com/vboard/s...d.php?t=483462

07-23-2013, 01:16 AM	#93
sacto67 Registered User Join Date: Sep 2011 Location: Sacramento Posts: 196	Re: Sacto67 Build diary I've gotten together some parts for an idea I have. This is a mixture of new Chevy, Honda, and BMW. The idea is for a new style emblem for the front fenders. New chevy is the bowtie from a SSR, Honda is the "I" and "O" from a new Pilot, and BMW is the idea of an amber light behind the emblem as a park/turn light. A buddy is woring on the amber backlight which I haven't gotten yet, but here is the bowtie and "10". Attached Images __________________ 1968 Chevy SWB stepside original USAF truck http://67-72chevytrucks.com/vboard/s...d.php?t=483462

07-23-2013, 10:04 AM	#94
Hardesty454 Registered User Join Date: Feb 2011 Location: Riverbank, Ca Posts: 1,006	Re: Sacto67 Build diary Well that's slick... Cool idea Posted via Mobile Device __________________ Rob 1971 c10 - ground up in progress Tripp's Speed Shop Build - http://67-72chevytrucks.com/vboard/s...d.php?t=589750



Register or Log In To remove these advertisements.

07-23-2013, 05:17 PM	#96
Saclandman Registered User Join Date: May 2013 Location: Sacramento, CA Posts: 487	Re: Sacto67 Build diary Just found this thread. Nice find. Glad to see it coming together. __________________ Rich J. 1967 Chevy C20 Longbed Stepside w/283 and 4spdSOLD 2002 Chevy Tahoe 4X4 5.3L SOLD 2015 Chevy Silverado Crew 4X4 5.3L

07-23-2013, 07:11 PM	#97
craig7070 Registered User Join Date: Jul 2013 Location: Roseville, CA Posts: 167	Re: Sacto67 Build diary Im in roseville...Where are all you sacramento guys at? Im new to the thread and love learning everything about these truck.. __________________ 1972 C10 Custom Deluxe 2 Owner Project "Lumberjack" 83K Original miles Work in progress....Got the truck for free all original

07-23-2013, 07:21 PM	#98
Saclandman Registered User Join Date: May 2013 Location: Sacramento, CA Posts: 487	Re: Sacto67 Build diary I'm in Natomas and my truck is up in Shingle Springs. Posted via Mobile Device __________________ Rich J. 1967 Chevy C20 Longbed Stepside w/283 and 4spdSOLD 2002 Chevy Tahoe 4X4 5.3L SOLD 2015 Chevy Silverado Crew 4X4 5.3L

07-23-2013, 07:47 PM	#99
sacto67 Registered User Join Date: Sep 2011 Location: Sacramento Posts: 196	Re: Sacto67 Build diary I'm near Rancho Cordova. __________________ 1968 Chevy SWB stepside original USAF truck http://67-72chevytrucks.com/vboard/s...d.php?t=483462

07-23-2013, 09:33 PM	#100
Rich916 Registered User Join Date: Dec 2009 Location: Rancho Cordova, CA Posts: 274	Re: Sacto67 Build diary I've seen that emblem, it's definetly top notch bling! __________________ 71 Short Step Build Thread http://67-72chevytrucks.com/vboard/s...d.php?t=429946

Thread Tools
Show Printable Version Email this Page
Display Modes
Linear Mode Switch to Hybrid Mode Switch to Threaded Mode

Register or Log In To remove these advertisements.