1963 C-10 in NC

[pimpston65]

Originally Posted by pimpston65

looking good sir!!!

are both your builds manuals? cuz i have an extra clutch delete plug if you need one.

[1963c-10]

Originally Posted by pimpston65

are both your builds manuals? cuz i have an extra clutch delete plug if you need one.

Clutch delete plug? Never heard of it. Stepside is a manual, fleetside will be an auto.

[aggie91]

I think he is talking about the plug that goes in the hole that the clutch linkage passes thru on the firewall to the Z bar.

Trucks are looking good.

[1963c-10]

Yeah....I could definitely use one. I was going to weld it up, but I'd rather have the plug.

[1963c-10]

Got the glass removed last night with help from Austin. Pinch welds all look great. Some light surface rust on the lower corners, but not rot or pinholes...and nothing the wire brush didn't take off. Should be able to finish prep on windshield opening....tape off and primer the rest of the interior tonight. MY goal at least. Hoping to get color down over the next weekend and start reassembly. Then back onto engine/trans.

[1963c-10]

Got seam sealer down last night. 2 coats sealer and 2 coats base so far. Need 1 more coat base and then clear

[Ta2Don]

Diggin' the Blue!!!

[1963c-10]

Up to 3 coats color..1 clear

[1963c-10]

Originally Posted by Ta2Don

Diggin' the Blue!!!

Thanks don. Its early 60's pepsi fleet blue

[pimpston65]

Originally Posted by 1963c-10

Thanks don. Its early 60's pepsi fleet blue

sorry dude i missed the postoffice drop off, they closed on me. so ima send those delete plugs on monday. paint should be dry by the time you get em...

[1963c-10]

No problem.

Last coat clear down. Came out great.

[TJ's Chevy]

DANG!!! Looks terrific!

[1963c-10]

Not bad for outside, 20gal portable compressor and home depot husky spray gun. Finish came out great, no runs

[62 Barnfind]

Looking good!

[1963c-10]

Originally Posted by 62 Barnfind

Looking good!

Thanks for the kind words. need to touch up the undercoating on the firwall. I did the undercoating 1st and oversprayed on purpose so the seams get double coated. The 3m seam sealer in the squeeze tube was easy to use. My buddy use to do glass for a living stopped by. He'll help me set the glass back in mon or wed next week. Ill hold o# reassembly until glass is in.

Heres a few more pics of finish. 1st one ive sprayed in 18 years.

[1963c-10]

Will do the doors this week and then prep exterior of the cab.

[1963c-10]

In case any ones interested:
Primer omni mp281 lacquer
Base omni dark pepsi blue 12908
Clear shop line jc630 polyurethane
And the clear hardner 4:1 shop line jh6370 polyurethane

[1963c-10]

Got the glass sealed into the gasket tonight. Will get the trim in tomorrow or monday. Lots of tape

[1963c-10]

Some more headway inside the cab. Got most of the dash switches in. Floor vents and cab light in. Taped off and sprayed the rear of the cab. And masked off the firewall and touched up the undercoating there.

[1963c-10]

Few pics of the dash.

Also did the window trim install just a few minutes ago. Undid one 1/4 of the tape, installed trim piece. Ewtaped using what I just removed and repeated process. The trim is the 60-61 wide trim and really makes the glass look good.

[Ta2Don]

Lookin' Good Brother!

[1963c-10]

Originally Posted by Ta2Don

Lookin' Good Brother!

Thanks don!!!

[pimpston65]

Originally Posted by 1963c-10

Thanks don!!!

whatchu gonna do when its all back together??? oh wait drive it!!!

[1963c-10]

Originally Posted by pimpston65

whatchu gonna do when its all back together??? oh wait drive it!!!

Haha, and then start the fleetside fulltime

[clemdaddy]

looks really good and i like that color of blue also. hard to believe it was painted outside... nice job.