SC Cabs For Patches and A 67 Fender For Patches

[wancosc356]

THIS STUFF IS GOING TO THE SCRAP YARD ON FRIDAY


Please post here before sending me a PM. I accept paypal (you pay the fees) or usps money order. Prices do not include shipping.

If you see something that you want and I don't have a price on it....feel free to ask.

1972 A/C cab for patches. Clean SC title. Has already been cut. Patches vary depending on size and cuts. Anywhere from $20-$50 for most patches.

1967 Non A/C Big Back Window cab for patches. No title. Patches vary depending on size and cuts. Anywhere from $20-$50 for most patches.

67 Fender for patches. Take the whole thing for $50.



72 A/C Cab for patches....



























67 Cab for patches....



















67 Fender for patches....

[wancosc356]

Ttt

[70BLAZERX2]

how much for the am radio..and the 2 knobs that hold it on the dash...i need something to fill the hole in my dash..dont have to work..

shipped to 37745 Greeneville TN

[wancosc356]

Originally Posted by 70BLAZERX2

how much for the am radio..and the 2 knobs that hold it on the dash...i need something to fill the hole in my dash..dont have to work..

shipped to 37745 Greeneville TN

I sold the retaining rings and knobs a while back. Ill do $60 shipped on the radio. Let me know.

[lvwyld1]

How much for the a/c section of the firewall on the 72? I just want the firewall with the correct openings for the a/c. I am interested for the right price. Thanks!

[lvwyld1]

Nevermind on the firewall piece....I found one locally! Thanks anyway!

[wancosc356]

Ttt

[projectjimmie68]

Looking for good rear floor corner patches. About a foot out from back wall and a foot in from rocker panel. Both sides plus shipping to zip 32136. Thanks

[jtp67-72]

Need both door jamb patches below door striker plate to top of rocker in 67 if possible-installing bear claws and these would be easy to adapt to fill where door striker plates are now on my cab--thanx jim

[creepdogg]

I need a center floor section where I had a 3 speed floor shifter hole cut out still have enough of the floor? I can send a photo too if needed.

[wancosc356]

Originally Posted by projectjimmie68

Looking for good rear floor corner patches. About a foot out from back wall and a foot in from rocker panel. Both sides plus shipping to zip 32136. Thanks

Ok....so u need a patch for both rear floor sections, a foot in from the back a foot in from the rocker, and how big do they need to be forward and towards the center?

Originally Posted by jtp67-72

Need both door jamb patches below door striker plate to top of rocker in 67 if possible-installing bear claws and these would be easy to adapt to fill where door striker plates are now on my cab--thanx jim

So below striker plate to the top of the rocker, and how far back into the rear of the cab?

Originally Posted by creepdogg

I need a center floor section where I had a 3 speed floor shifter hole cut out still have enough of the floor? I can send a photo too if needed.

The center floor section looks good. A photo would be good and/or some measurements.

[bigyellow]

how much for sway bar and brackets?

[wancosc356]

Originally Posted by creepdogg

I will post up a pic sometime this weekend, tks

Sounds good.

Originally Posted by projectjimmie68

A foot square....

Ok. Let me check it out and Ill get back to you.

Originally Posted by bigyellow

how much for sway bar and brackets?

I'll have to look and see if I still have it somewhere. Someone bought the front suspension and rear axle a while back. Not sure if they took that or not. Ill get back to you.

[jtp67-72]

I will post pic in am of exact cut i need in door jamb........jim

[projectjimmie68]

would like to see the corners in question. Thanks

[wancosc356]

Originally Posted by jtp67-72

I will post pic in am of exact cut i need in door jamb........jim

Sounds good.

Originally Posted by projectjimmie68

would like to see the corners in question. Thanks

You can see the floor in the yellow cab. That area that you want looks good.

[wancosc356]

PM Sent

[LTRAJE]

How much for these pieces? Both pass and drivers side?

[creepdogg]

I need a center floor piece, basically the part that people switch over to a high hump, I had a floor shifter in at one time, need to patch her up clean, here is a pic of the piece, you can see the nasty filler piece in there now. Let me know if you can hook me up

thanks


Chris

[Triple B]

Im looking for left rear stepside fender. Some reason your pictures wont show up on my message boards. could you send me a pic of what you have in a message?

[indyracer]

I am looking for the two spots I have outlined. Let me know what you can do and the cost.

[wancosc356]

Originally Posted by LTRAJE

How much for these pieces? Both pass and drivers side?

$30 each plus shipping...if they are in good shape. I'll double check this afternoon and get back to you.

Originally Posted by creepdogg

I need a center floor piece, basically the part that people switch over to a high hump, I had a floor shifter in at one time, need to patch her up clean, here is a pic of the piece, you can see the nasty filler piece in there now. Let me know if you can hook me up

thanks


Chris

I can get you that piece cut out for $40 plus shipping.

Originally Posted by Triple B

Im looking for left rear stepside fender. Some reason your pictures wont show up on my message boards. could you send me a pic of what you have in a message?

No stepside fenders. Sorry.

Originally Posted by indyracer

I am looking for the two spots I have outlined. Let me know what you can do and the cost.

I can cut those pieces for $40 for the both plus shipping.

[indyracer]

I was just looking over my post after you replied and I wanted to clarify what I wanted. I want the complete corner, door jamb and all. You may have already thought that, but I wanted to make sure because it does look like I was maybe talking about just the area around the window.

[creepdogg]

I can get you that piece cut out for $40 plus shipping.



How big of a piece do you think you will cut out? Should I send you another pic with some tape outlining exactly how big I would like?

Thanks

[wancosc356]

Originally Posted by indyracer

I was just looking over my post after you replied and I wanted to clarify what I wanted. I want the complete corner, door jamb and all. You may have already thought that, but I wanted to make sure because it does look like I was maybe talking about just the area around the window.

Oh ok. I thought u did want just the area around the window. But I can do the complete corner too. $50 for both sound fair?

Originally Posted by creepdogg

I can get you that piece cut out for $40 plus shipping.



How big of a piece do you think you will cut out? Should I send you another pic with some tape outlining exactly how big I would like?

Thanks

However big you want. You can do that or just get me some measurements.