slammed 57 - Page 9 - The 1947 - Present Chevrolet & GMC Truck Message Board Network

**slammed57** · 11-19-2019, 06:08 PM

Went with Marman clamps to change out the mufflers (if I get tired of it being to loud) and also cut the old style exhaust flanges out ( Always had issues with the exhaust flange gaskets or the flanges them selves bending and not sealing right) So I cut the ends off and putting Marman clamps there as well. They seal great and last a long time. also going with these industrial flex fittings

**slammed57** · 11-19-2019, 06:12 PM

practiced tig welding with silicone bronze and making some pie cut fittings so i can get the exhaust over the rear axle and out the back. I may try some 308L ss tig rods to see the difference

**joedoh** · 11-19-2019, 09:11 PM

looking good!

Quote:

Originally Posted by slammed57

if I get tired of it being to loud

said no one, ever.

my56chevytruck · 11-20-2019, 12:35 AM

Quote:

Originally Posted by slammed57

practiced tig welding with silicone bronze and making some pie cut fittings so i can get the exhaust over the rear axle and out the back. I may try some 308L ss tig rods to see the difference

Hey my friend, great to see you're back. good work Mike

**slammed57** · 11-20-2019, 10:17 PM

Quote:

Originally Posted by joedoh

looking good!

said no one, ever.

lol very true!!!

**slammed57** · 11-23-2019, 02:43 PM

Quote:

Originally Posted by my56chevytruck

Hey my friend, great to see you're back. good work Mike

Thanks morrie

**slammed57** · 12-03-2019, 09:10 PM

before I install the exhaust system , I decided to stiffen up the frame mid section and fabricated a trans mount as well.

Jason 56 · 12-04-2019, 12:02 AM

I like the additional support. 2x6? Post some more pics of the other end if you could. Your exhaust going to tuck up along the bottom of it?

**slammed57** · 12-06-2019, 06:51 PM

Quote:

Originally Posted by Jason 56

I like the additional support. 2x6? Post some more pics of the other end if you could. Your exhaust going to tuck up along the bottom of it?

I went with 2x4 and centered it on the 2x6 rails so it would leave a inch above and below so I can run air lines, brake lines and electrical in a continuous straight line

**slammed57** · 12-15-2019, 05:03 PM

whole new respect for the guys that build exhausts for a living. this was my first time building a exhaust system . tried hard to go over the axles but there was now way of doing so with out raising the bed more that what it already is. but its done. next on the list is gas pedal and firewall brake and clutch assembly.

hotrod1 · 12-15-2019, 11:50 PM

Nice work!

my56chevytruck · 12-16-2019, 07:36 PM

Quote:

Originally Posted by slammed57

whole new respect for the guys that build exhausts for a living. this was my first time building a exhaust system . tried hard to go over the axles but there was now way of doing so with out raising the bed more that what it already is. but its done. next on the list is gas pedal and firewall brake and clutch assembly.

great job as usual Mike. You do very good work.

**slammed57** · 01-13-2020, 06:17 PM

Had cut into the recessed fire wall and section out a little area for the lokar gas pedal would only reach 1/2 throttle. After the sectioned area I have full throttle no problem. Also installed the pedal assembly. I also ordered today wilwood front and rear discs/calipers as well the master cylinder. So Iam lookin forward for it to get here.

**oldman3** · 01-13-2020, 09:29 PM

Looks good...Jim

BAM55 · 01-16-2020, 04:07 PM

Looking good man, everything is looking really good.

62 Barnfind · 01-16-2020, 08:31 PM

Nice job!

Oldtruckwelder · 01-18-2020, 08:45 AM

Awesome job as usual Slammed..
Lokar makes some nice stuff.
JT from SC

**slammed57** · 01-18-2020, 10:44 AM

Quote:

Originally Posted by oldman3

Looks good...Jim

thanks bud

**slammed57** · 01-18-2020, 10:45 AM

Quote:

Originally Posted by BAM55

Looking good man, everything is looking really good.

thanks bam. hows the truck coming along?

**slammed57** · 01-18-2020, 10:46 AM

Quote:

Originally Posted by Oldtruckwelder

Awesome job as usual Slammed..
Lokar makes some nice stuff.
JT from SC

Yes sir they do. thanks so much

my56chevytruck · 01-20-2020, 11:21 AM

Quote:

Originally Posted by slammed57

Yes sir they do. thanks so much

the work as usual is great, nice pedals to Mike. Is that all billet??

**slammed57** · 01-20-2020, 03:25 PM

Quote:

Originally Posted by my56chevytruck

the work as usual is great, nice pedals to Mike. Is that all billet??

Hey morrie... they are from lokar , not sure if they are billet or not.... could be

dsraven · 01-23-2020, 02:50 AM

nice forward thinking on the planning of things. stuff unbolts and room left for brake lines etc. a lot of guys forget that little stuff.

**slammed57** · 01-24-2020, 01:25 PM

Quote:

Originally Posted by dsraven

nice forward thinking on the planning of things. stuff unbolts and room left for brake lines etc. a lot of guys forget that little stuff.

Thanks bud, I agree. but no matter how much I try to pre plan ,something comes along and i say " crap I didnt think of that" lol

**slammed57** · 01-24-2020, 09:55 PM

The wife says” why you keep starting at them, they’re only brakes” big sigh, she’ll never understand. I always wanted a set of these, needless to say I’ll be busy all day tomorrow putting them on

11-19-2019, 06:08 PM	#201
slammed57 Senior Member Join Date: Jan 2015 Location: pembroke pines, fl Posts: 707	Re: slammed 57 Went with Marman clamps to change out the mufflers (if I get tired of it being to loud) and also cut the old style exhaust flanges out ( Always had issues with the exhaust flange gaskets or the flanges them selves bending and not sealing right) So I cut the ends off and putting Marman clamps there as well. They seal great and last a long time. also going with these industrial flex fittings Attached Images __________________ My 57 current build http://67-72chevytrucks.com/vboard/s...d.php?t=662590

11-19-2019, 06:12 PM	#202
slammed57 Senior Member Join Date: Jan 2015 Location: pembroke pines, fl Posts: 707	Re: slammed 57 practiced tig welding with silicone bronze and making some pie cut fittings so i can get the exhaust over the rear axle and out the back. I may try some 308L ss tig rods to see the difference Attached Images __________________ My 57 current build http://67-72chevytrucks.com/vboard/s...d.php?t=662590 Last edited by slammed57; 11-19-2019 at 06:30 PM.

12-03-2019, 09:10 PM	#207
slammed57 Senior Member Join Date: Jan 2015 Location: pembroke pines, fl Posts: 707	Re: slammed 57 before I install the exhaust system , I decided to stiffen up the frame mid section and fabricated a trans mount as well. Attached Images __________________ My 57 current build http://67-72chevytrucks.com/vboard/s...d.php?t=662590

12-04-2019, 12:02 AM	#208
Jason 56 Registered User Join Date: Nov 2018 Location: Ishpeming, mi Posts: 625	Re: slammed 57 I like the additional support. 2x6? Post some more pics of the other end if you could. Your exhaust going to tuck up along the bottom of it? __________________ http://67-72chevytrucks.com/vboard/s...d.php?t=780018 Jason’s 56 build

12-15-2019, 05:03 PM	#210
slammed57 Senior Member Join Date: Jan 2015 Location: pembroke pines, fl Posts: 707	Re: slammed 57 whole new respect for the guys that build exhausts for a living. this was my first time building a exhaust system . tried hard to go over the axles but there was now way of doing so with out raising the bed more that what it already is. but its done. next on the list is gas pedal and firewall brake and clutch assembly. Attached Images __________________ My 57 current build http://67-72chevytrucks.com/vboard/s...d.php?t=662590

12-15-2019, 11:50 PM	#211
hotrod1 56 - autocross Join Date: Apr 2010 Location: Camarillo, Ca Posts: 1,121	Re: slammed 57 Nice work!

01-13-2020, 06:17 PM	#213
slammed57 Senior Member Join Date: Jan 2015 Location: pembroke pines, fl Posts: 707	Re: slammed 57 Had cut into the recessed fire wall and section out a little area for the lokar gas pedal would only reach 1/2 throttle. After the sectioned area I have full throttle no problem. Also installed the pedal assembly. I also ordered today wilwood front and rear discs/calipers as well the master cylinder. So Iam lookin forward for it to get here. Attached Images __________________ My 57 current build http://67-72chevytrucks.com/vboard/s...d.php?t=662590 Last edited by slammed57; 01-14-2020 at 07:50 PM.

01-13-2020, 09:29 PM	#214
oldman3 Senior Member Join Date: Mar 2011 Location: West Plains, Missouri Posts: 7,559	Re: slammed 57 Looks good...Jim __________________ my build thread: http://67-72chevytrucks.com/vboard/s...d.php?t=459839 Jimbo's long bed step build:http://67-72chevytrucks.com/vboard/s...t=464626<br />

01-16-2020, 04:07 PM	#215
BAM55 Registered User Join Date: Jan 2016 Location: Inglewood, CA Posts: 324	Re: slammed 57 Looking good man, everything is looking really good. __________________ BAM 55/58 Chevy Truck Project Fixing a mess of a clip installation

01-16-2020, 08:31 PM	#216
62 Barnfind Registered User Join Date: Jan 2012 Location: Killeen, Tx Posts: 1,373	Re: slammed 57 Nice job! __________________ John Z 1962 Chevy C10 Stepside 62 Barnfind My build tread: http://67-72chevytrucks.com/vboard/s...d.php?t=507513

01-18-2020, 08:45 AM	#217
Oldtruckwelder Registered User Join Date: May 2015 Location: Jackson SC Posts: 113	Re: slammed 57 Awesome job as usual Slammed.. Lokar makes some nice stuff. JT from SC

01-23-2020, 02:50 AM	#223
dsraven Registered User Join Date: Nov 2010 Location: calgary alberta Posts: 8,322	Re: slammed 57 nice forward thinking on the planning of things. stuff unbolts and room left for brake lines etc. a lot of guys forget that little stuff.

01-24-2020, 09:55 PM	#225
slammed57 Senior Member Join Date: Jan 2015 Location: pembroke pines, fl Posts: 707	Re: slammed 57 The wife says” why you keep starting at them, they’re only brakes” big sigh, she’ll never understand. I always wanted a set of these, needless to say I’ll be busy all day tomorrow putting them on Attached Images __________________ My 57 current build http://67-72chevytrucks.com/vboard/s...d.php?t=662590

Thread Tools
Show Printable Version Email this Page
Display Modes
Linear Mode Switch to Hybrid Mode Switch to Threaded Mode



Register or Log In To remove these advertisements.

Register or Log In To remove these advertisements.