1968

[gdavis]

Originally Posted by RenoKeene

Truck looks great George! I'm just north of you a bit, maybe I'll cruise down in mine after the Love Bugs disappear.
Brad

thanks a lot man and any time give me a call thru a PM

[gdavis]

Today, I went and tried to get the front end adjusted, Like I said tried. He couldn't do the toe and camber. He said that he couldn't take the bolts off. I had them off three years ago but he didn't charge me nothing. The truck has a few issues so I will be working on them starting Monday.

[Xeen]

I hope he didn't use metric tools and round off the nut's and then be like "I couldn't get them off" like a pro.

[swamp rat]

Open this Google search and read the posts, the first one especially.

https://www.google.com/search?newwin...15.wkCglJAtWhg

[gdavis]

Guys what is the worst thing that could happen to our trucks except having a accident.
Well, it is having your engine start to knock after only 10 minutes of running time. So I pulled the engine back out of the truck and took it apart. What I found was I forgot to torque the mains. I guess I was in a hurry or someone came in the shop and bothered me and I must have forgot. Well, it didn't do any damage to the engine except for the bearings. So I went and got another set of mains and rods and rings and a complete gasket set. This time I am not making that mistake again. When I seen the bolts I couldn't believe I done that. All was finger tight. I am one lucky guy. It pays to double check our work and when doing a engine get everybody out of the shop. I upgraded on the rings this time to poly rings. Longer life wear.

[colgad]

Sorry to hear that bad news George! Glad no machining was necessary.

I am swapping engines (due to a knock) in my newly acquired Jimmy but I have not started the job yet. I knew it was bad when I got it.

[sduckworth13]

Dang George, sorry to hear about the engine. Sounds like you have it under control. Good luck.

[Xeen]

Sorry to hear that George, chin up you got off cheap considering it could have been a lot worse, plus you got to improve it by installing moly rings.

[swamp rat]

Oh man, real glad there was no damage, just double check and triple check everything when it go's back together, torque, plasti gauge the new bearings, pistone and rods, everything. Good luck!

[gdavis]

Guys thanks for the incouragement .I worked on the cleaning the parts today. Got everything cleaned and wrapper up. I sprayed everything down with WD-40 so no rust would appear. I cleaned the crank and there was a few real light scratches on the main, so I sent the crank out to be polished. I probably could have removed them with some emery cloth but I went ahead and had some machine work done on the crank. This way I know that it want give me any problems. It would always be on the back of my mine every time I heard a noise if I didn't so what the hey. It's only 60.00 so I will get it back Friday morning. My plans are for Monday morning put the engine back together. So by Friday I will have the motor back in the truck and running.

[gdavis]

pictures of the clean parts

[gdavis]

Originally Posted by colgad

Sorry to hear that bad news George! Glad no machining was necessary.

I am swapping engines (due to a knock) in my newly acquired Jimmy but I have not started the job yet. I knew it was bad when I got it.

I like the army green color. It makes it look tuff, George

[swamp rat]

I'd go ahead and dump that oil flter now and fill a new one with oil before you spin it on to the block, cheap insurance.

[Xeen]

Originally Posted by swamp rat

I'd go ahead and dump that oil flter now and fill a new one with oil before you spin it on to the block, cheap insurance.

Agreed and make it a Fram tough guard while you are at it.

[gdavis]

Originally Posted by swamp rat

I'd go ahead and dump that oil flter now and fill a new one with oil before you spin it on to the block, cheap insurance.

Yea I will get a new filter I only keeping the old one until I need it. This was it will be clean and no dust will get in there.

[gdavis]

Originally Posted by Xeen

Agreed and make it a Fram tough guard while you are at it.

Yea that filter came with the oil I was using to break in the engine. I always use Fram filters. I am looking forward into putting this engine back together

[gdavis]

Monday, I will be putting the engine back together. I have a friend that is a mech. and he will be helping me this time. two heads is better than one. I picked up the stuff that I know I will be needing to put the engine back together. Also the machine shop only charged me 20.00 for the polish of the crank. He said I have enough expence as it was. so he cut me a break. here is a few pictures of the items and the crank.

[gdavis]

Got the motor over hauled today. A friend came over and helped me out. I will re marry the transmission to the motor tomorrow and hopefully install it on Wednesday.

[Xeen]

Originally Posted by gdavis

Got the motor over hauled today. A friend came over and helped me out. I will re marry the transmission to the motor tomorrow and hopefully install it on Wednesday.

I'm glad to hear it George, good job on a fast turn around time.
While the motor is out you should take advantage and seal up the holes in the drivers side firewall lower pinch weld.

[colgad]

Great news George! Hoping it all goes great from here.

Got my Jimmy's engine pulled out and ripped apart. It was the number 6 rod bearing (spun). I am junking the 89 350 engine (single rear main seal but not a roller motor) and using my 5.3 Lsx engine. It will take me longer to install but better in the end.

Again, great new glad nothing was damaged

[gdavis]

Originally Posted by Xeen

I'm glad to hear it George, good job on a fast turn around time.
While the motor is out you should take advantage and seal up the holes in the drivers side firewall lower pinch weld.

motor back in the truck. But I do need a clutch delete plug a steel one. the platic ones just isn't worth the trouble putting them in.

[gdavis]

Originally Posted by colgad

Great news George! Hoping it all goes great from here.

Got my Jimmy's engine pulled out and ripped apart. It was the number 6 rod bearing (spun). I am junking the 89 350 engine (single rear main seal but not a roller motor) and using my 5.3 Lsx engine. It will take me longer to install but better in the end.

Again, great new glad nothing was damaged

yea me too. I had help getting the motor back together. good luck with the LS engine

[gdavis]

Today, I married the transmission to the engine and installed it back in the truck. I will have a few items to button up tomorrow.

[swamp rat]

Nice work George!

[gdavis]

Originally Posted by swamp rat

Nice work George!

Thanks a lot.