|
04-17-2004, 12:09 AM
|
#1 |
|
Registered User
Join Date: Jan 2004
Location: Garland TX Dallas area
Posts: 658
|
Cleaning interior
Would like to know how some of you clean the interior. I don’t have a headliner so there is a lot of metal and I do not use anything to mess up the paint.
|
|
|
|
04-17-2004, 12:55 AM
|
#2 |
|
KEEP ON TRUCKING
Join Date: Sep 2000
Location: martinsville va
Posts: 2,563
|
mostley just warm water and a small amount of soap in it just ring the rag out good so you dont have water everywhere
__________________
72 cheyenne 2wd lwb 71 k20 sons bassett va |
|
|
|
|
04-17-2004, 06:04 AM
|
#3 |
|
Low & Slow
Join Date: Dec 2002
Location: Oklahoma
Posts: 1,047
|
My truck only gets dust and dead grass in it so I mostly just wipe it down with a damp rag to catch any of the dust/dirt that is on the paint.
__________________
70' C-10 LWB Fleetside 4.5/6 drop 
|
|
|
|
|
04-17-2004, 08:46 AM
|
#4 |
|
Registered User
Join Date: Jan 2003
Location: Washington State
Posts: 8,831
|
Any help with mold.....?
__________________
1970 Chev CST 2003 Harley Fatboy 1975 Chevrolet Step Van 1956 Chev Bel Air 1977 Blazer 2WD For Sale $3000.00 1978 Blazer 2WD For Sale $7000.00 1978 Silverado 2005 Monte Carlo |
|
|
|
|
04-17-2004, 09:01 AM
|
#5 |
|
Registered User
Join Date: Mar 2004
Location: Virginia beach, Va
Posts: 209
|
The first weekend I had my truck I tore out all the interior, and pressure washed for about 22 hours in 2 days. may seem like a little much, but the truck had an inch of moss and mold in some places. in most places it was just about a quarter of an inch.
I still do that with my tacoma every now and then I run the pressure washer throught the inside. just being carefull of the dash, and stuff.
__________________
~Christopher L. Orr 71 c20, 454- Stolen While Deployed. dynoed at 550 ft lbs, 425 hp at 3000 rpm (mustang dyno). TH400 3500 stall.... etc, etc. |
|
|
|
|
04-17-2004, 11:42 AM
|
#6 |
|
Senior Member
Join Date: Mar 2004
Location: Tulsa,Oklahoma
Posts: 606
|
I have used a product called TSP don't know the full name it but you can get it at Walmart in the part dept. or Lowes,Home Depot.The stuff cuts thru grease,grime and anything else like a hot knife thru butter,I use it all the time for just about everything..
__________________
1961 BUICK LESABRE ** 1968 CHEVELLE SS 396 ** 1969 BUICK RIVIERA GS ** 1971 2 WHEEL DRIVE BLAZER ** 1971 4X4 BLAZER ** 1971 SHORTBED CHEYENNE FLEETSIDE ** 1971 SHORTBED 4X4 FLEETSIDE ** ...My Ebay |
|
|
|
|
04-18-2004, 01:32 AM
|
#7 |
|
Registered User
 Join Date: Dec 2002
Location: Northern Virginia
Posts: 1,268
|
Bleach and water.anything chem that removes it will have bleach in it
|
|
|
|
|
04-18-2004, 01:52 AM
|
#8 |
|
its all about the +6 inches
Join Date: Jan 2001
Location: Hilliard Ohio
Posts: 2,690
|
It's not a bad idea to wax all the painted surfaces in the cab once a year too...perferably in the early spring when the metal is cool to the touch. You'll be amazed at how the dash will 'glow' after doing it for the first time.
|
|
|
|
|
04-18-2004, 10:51 AM
|
#9 |
|
PROJECT 7DEUCE
Join Date: Dec 2002
Location: GRANTS PASS OR
Posts: 21,606
|
Blue mold is very hard to get rid of I had to wash the whole interior with bleech and oxy-clean.... BTW mold neveer goes away...
__________________
GO BIG GREEN  GO DUCKSMEMBER #6377 72 k-5 daily driver 6'' lift 35'' 350-350-205 slowly getting rust free. Project "7DEUCE" check out my build http://67-72chevytrucks.com/vboard/s...d.php?t=267665 Tim Powell..R.I.P EastSideLowlife..... R.I.P.. |
|
|
|
 |
| Bookmarks |
| Thread Tools | |
| Display Modes | |
|
|
Linear Mode
