Mini tub's ?????? - The 1947 - Present Chevrolet & GMC Truck Message Board Network

FRENCHBLUE72 · 06-06-2004, 06:04 PM

Those of you who have bag's or a 6-8'' rear drop do your inner bed wheel well's still fit???? I was gonna mini tub the truck using stock well's but I am looking ahead to bag's and wondering if the are gonna rub on a wheel from 17'' to 20'' need some feedback on this thank's guy's ....If you fabbed or made the stocke well's work pic's would be great...

FRENCHBLUE72 · 06-07-2004, 12:29 AM

Ttt
Ttt
Ttt
Ttt

SCOTI · 06-13-2004, 10:49 PM

If the rear tire is over 28" tall, then @ 8" drop you will more than likely rub the top of the tubs. With 295/40/20's on 20x10's w/@ least 8" drop, mine rubbed & required raising the floor/tubs to clear.

FRENCHBLUE72 · 06-13-2004, 10:51 PM

Thank's for the reply do you happen to have any pic's????

SCOTI · 06-14-2004, 06:59 PM

Notice the bedfloor where it meets the bedside. It's now 3" above the lip of the bedside.

SCOTI · 06-14-2004, 07:07 PM

You can see the tops of the tubs are now even w/the factory body line of the inner bedside. It's not really noticeable (just look @ a factory bed to see the 3" difference).

SCOTI · 06-14-2004, 07:14 PM

Here's another angle that shows both the top & bottom against the factory bodyline of the inner bedside. My plan was to use a spray in bedliner to help 'hide' the original lower bodyline. But, I'm kinda' anal so I might just section the inner bedside altogether to keep the lines as GM intended . . .... minus 3".

FRENCHBLUE72 · 06-14-2004, 11:11 PM

That's is just what i was looking for that is some killer work you do... I am just guessing that you raised the frame mout's up to meet the new floor or is the truck body dropped???

SCOTI · 06-14-2004, 11:53 PM

Spacers made from 1" square tubing.

406_SBC · 06-22-2004, 02:00 AM

Question guys
on a 67-72 shortbox fleetside what would be the widest tire you could go with?, saying you drop it roughly 4 inchs from stock, using whatever back spacing required..I know a 295 fits know problem.

72MARIO · 06-23-2004, 09:25 PM

Wow That's Frigging Nice Work ! I love the way you finished the floor. I understand the hours involved in doing that kind of work.

SCOTI · 06-23-2004, 10:39 PM

Quote:

Originally Posted by 406_SBC

Question guys
on a 67-72 shortbox fleetside what would be the widest tire you could go with?, saying you drop it roughly 4 inchs from stock, using whatever back spacing required..I know a 295 fits know problem.

If you widen the tubs, 15x14's will fit w/31x18.5" wide Mickey t's w/o rubbing the frame (for comparison, 295's are about 11-12"). Once upon a time that's what was hidden under those green wheeltubs in the pics.

406_SBC · 06-24-2004, 01:51 AM

Oh ok! yeah cause my dad had 16.50' hoosiers on his truck, they didn't come close to rubbing the frame at all. I was just curious without tubbing it out,just a stock fleetside box, what size tire you figure would fit?, like 305 or maybe a 325?
Thanks

SCOTI · 06-24-2004, 07:33 PM

Lowered 4"? . . ..... 325mm max on a 10" wheel. My guess is that would still want to buzz the outer wheel well lip.

Putter · 06-25-2004, 08:49 AM

406 SBC, I had a '69 fleet side that was lowered roughly 4 inches and I was running a 305 without rubbing. I don't remember if the rims were 10s or 12s (I am thinking 10s for some reason).

06-06-2004, 06:04 PM	#1
FRENCHBLUE72 PROJECT 7DEUCE Join Date: Dec 2002 Location: GRANTS PASS OR Posts: 21,606	Mini tub's ?????? Those of you who have bag's or a 6-8'' rear drop do your inner bed wheel well's still fit???? I was gonna mini tub the truck using stock well's but I am looking ahead to bag's and wondering if the are gonna rub on a wheel from 17'' to 20'' need some feedback on this thank's guy's ....If you fabbed or made the stocke well's work pic's would be great...

06-13-2004, 10:49 PM	#3
SCOTI Registered User Join Date: Apr 2001 Location: DALLAS,TX Posts: 22,064	If the rear tire is over 28" tall, then @ 8" drop you will more than likely rub the top of the tubs. With 295/40/20's on 20x10's w/@ least 8" drop, mine rubbed & required raising the floor/tubs to clear. __________________ 67SWB-B.B.RetroRod 64SWB-Recycle 89CCDually-Driver/Tow Truck 99CCSWB Driver All Fleetsides @rattlecankustoms in IG Building a small, high rpm engine with the perfect bore, stroke and rod ratio is very impressive. It's like a highly skilled Morrocan sword fighter with a Damascus Steel Scimitar..... *Cubic inches is like Indiana Jones with a cheap pistol.*

06-14-2004, 06:59 PM	#5
SCOTI Registered User Join Date: Apr 2001 Location: DALLAS,TX Posts: 22,064	Here's a shot of the pass side. . ..... Notice the bedfloor where it meets the bedside. It's now 3" above the lip of the bedside. Attached Images __________________ 67SWB-B.B.RetroRod 64SWB-Recycle 89CCDually-Driver/Tow Truck 99CCSWB Driver All Fleetsides @rattlecankustoms in IG Building a small, high rpm engine with the perfect bore, stroke and rod ratio is very impressive. It's like a highly skilled Morrocan sword fighter with a Damascus Steel Scimitar..... *Cubic inches is like Indiana Jones with a cheap pistol.*

06-14-2004, 07:07 PM	#6
SCOTI Registered User Join Date: Apr 2001 Location: DALLAS,TX Posts: 22,064	W/the tubs installed . . .... You can see the tops of the tubs are now even w/the factory body line of the inner bedside. It's not really noticeable (just look @ a factory bed to see the 3" difference). Attached Images __________________ 67SWB-B.B.RetroRod 64SWB-Recycle 89CCDually-Driver/Tow Truck 99CCSWB Driver All Fleetsides @rattlecankustoms in IG Building a small, high rpm engine with the perfect bore, stroke and rod ratio is very impressive. It's like a highly skilled Morrocan sword fighter with a Damascus Steel Scimitar..... *Cubic inches is like Indiana Jones with a cheap pistol.*

06-14-2004, 07:14 PM	#7
SCOTI Registered User Join Date: Apr 2001 Location: DALLAS,TX Posts: 22,064	From the front . . .... Here's another angle that shows both the top & bottom against the factory bodyline of the inner bedside. My plan was to use a spray in bedliner to help 'hide' the original lower bodyline. But, I'm kinda' anal so I might just section the inner bedside altogether to keep the lines as GM intended . . .... minus 3". Attached Images __________________ 67SWB-B.B.RetroRod 64SWB-Recycle 89CCDually-Driver/Tow Truck 99CCSWB Driver All Fleetsides @rattlecankustoms in IG Building a small, high rpm engine with the perfect bore, stroke and rod ratio is very impressive. It's like a highly skilled Morrocan sword fighter with a Damascus Steel Scimitar..... *Cubic inches is like Indiana Jones with a cheap pistol.*

06-07-2004, 12:29 AM	#2
FRENCHBLUE72 PROJECT 7DEUCE Join Date: Dec 2002 Location: GRANTS PASS OR Posts: 21,606	Ttt Ttt Ttt Ttt

06-13-2004, 10:51 PM	#4
FRENCHBLUE72 PROJECT 7DEUCE Join Date: Dec 2002 Location: GRANTS PASS OR Posts: 21,606	Thank's for the reply do you happen to have any pic's????

06-14-2004, 11:11 PM	#8
FRENCHBLUE72 PROJECT 7DEUCE Join Date: Dec 2002 Location: GRANTS PASS OR Posts: 21,606	That's is just what i was looking for that is some killer work you do... I am just guessing that you raised the frame mout's up to meet the new floor or is the truck body dropped???

06-14-2004, 11:53 PM	#9
SCOTI Registered User Join Date: Apr 2001 Location: DALLAS,TX Posts: 22,064	Spacers made from 1" square tubing. __________________ 67SWB-B.B.RetroRod 64SWB-Recycle 89CCDually-Driver/Tow Truck 99CCSWB Driver All Fleetsides @rattlecankustoms in IG Building a small, high rpm engine with the perfect bore, stroke and rod ratio is very impressive. It's like a highly skilled Morrocan sword fighter with a Damascus Steel Scimitar..... *Cubic inches is like Indiana Jones with a cheap pistol.*

06-22-2004, 02:00 AM	#10
406_SBC Registered User Join Date: Jun 2004 Location: Kelowna,B.C,Canada Posts: 150	Question guys on a 67-72 shortbox fleetside what would be the widest tire you could go with?, saying you drop it roughly 4 inchs from stock, using whatever back spacing required..I know a 295 fits know problem.

06-23-2004, 09:25 PM	#11
72MARIO Registered User Join Date: Nov 2000 Location: Huntsville Ontario Canada Posts: 4,051	Wow That's Frigging Nice Work ! I love the way you finished the floor. I understand the hours involved in doing that kind of work. __________________ 1968 Suburban numbers matching all original truck now equipped with 6.0/4L80 on Accuair http://67-72chevytrucks.com/vboard/s...d.php?t=625017 1967 C/20 6.0/4L80 Roofing Truck 1990 V2500 Suburban "Plow Truck" 2005 TAHOE DD

06-24-2004, 01:51 AM	#13
406_SBC Registered User Join Date: Jun 2004 Location: Kelowna,B.C,Canada Posts: 150	Oh ok! yeah cause my dad had 16.50' hoosiers on his truck, they didn't come close to rubbing the frame at all. I was just curious without tubbing it out,just a stock fleetside box, what size tire you figure would fit?, like 305 or maybe a 325? Thanks

06-24-2004, 07:33 PM	#14
SCOTI Registered User Join Date: Apr 2001 Location: DALLAS,TX Posts: 22,064	Lowered 4"? . . ..... 325mm max on a 10" wheel. My guess is that would still want to buzz the outer wheel well lip. __________________ 67SWB-B.B.RetroRod 64SWB-Recycle 89CCDually-Driver/Tow Truck 99CCSWB Driver All Fleetsides @rattlecankustoms in IG Building a small, high rpm engine with the perfect bore, stroke and rod ratio is very impressive. It's like a highly skilled Morrocan sword fighter with a Damascus Steel Scimitar..... *Cubic inches is like Indiana Jones with a cheap pistol.*

06-25-2004, 08:49 AM	#15
Putter More Cowbell.... Join Date: Mar 2004 Location: Puckett, MS Posts: 3,569	406 SBC, I had a '69 fleet side that was lowered roughly 4 inches and I was running a 305 without rubbing. I don't remember if the rims were 10s or 12s (I am thinking 10s for some reason). __________________ *There once was a member from Puckett.....Who ( fill in the blank blank blank* ) bucket**

Thread Tools
Show Printable Version Email this Page
Display Modes
Linear Mode Switch to Hybrid Mode Switch to Threaded Mode



Register or Log In To remove these advertisements.

Register or Log In To remove these advertisements.