![]() |
Register or Log In To remove these advertisements. |
|
|
![]() |
|
Thread Tools | Display Modes |
![]() |
#1 |
Registered User
Join Date: Apr 2004
Location: Clanton, AL
Posts: 1,253
|
If replacing floor panels, do I need new rockers too?
Hey Guys,
I am finally about to start replacing sheetmetal on my '70 C-10. On the left side, I need a rocker. On the Right, the rocker & everything near it is rusted away. My question is this: If I use Front & Rear floor patch panels, do I need new rockers as well, or are the rockers already part of the new floor panels? Also, any tips before I start would be Most appreciated! Thanks, John
__________________
85' CUCV M1009!!! The newest addition! 6.2diesel, Th400, NP208, & only 36k miles! 70' C-10 LWB Fleetside - Looking good these days! ![]() 05' Dodge Neon 88' Winner Escape Sport 1750 - 4.3v6 94' Seadoo SP 84' Honda TRX200, bare nekkid. Just a frame & tires. Always looking for another project or any good deal! ![]() |
![]() |
![]() |
![]() |
#2 |
Registered User
Join Date: Jun 2004
Location: Beeville, Texas
Posts: 1,943
|
Rocker panels are separate from the floor panels. So you'd need front and rear floors, and left and right rockers, and most likely the rocker backing plates too. You might check your cab floor supports, also.
__________________
RJD 1984 Chevrolet C30 welding truck 454/SM465 1977 GMC C15 pickup 350/TH350 1970 Chevrolet C20 pickup 350/TH400 1970 Chevrolet K20 Suburban 454/TH350 1969 GMC 8500 478M V6/5 spd winch truck |
![]() |
![]() |
![]() |
#3 |
Account Suspended
Join Date: Sep 2000
Posts: 4,002
|
All floor patches I have seen have the rocker backing plate built in to them.
|
![]() |
![]() |
![]() |
#4 | |
Registered User
Join Date: Jun 2004
Location: Beeville, Texas
Posts: 1,943
|
Quote:
OK, thanks for correcting me. ![]()
__________________
RJD 1984 Chevrolet C30 welding truck 454/SM465 1977 GMC C15 pickup 350/TH350 1970 Chevrolet C20 pickup 350/TH400 1970 Chevrolet K20 Suburban 454/TH350 1969 GMC 8500 478M V6/5 spd winch truck |
|
![]() |
![]() |
![]() |
#5 |
Registered User
Join Date: Nov 2001
Location: Concord, NC
Posts: 2,489
|
John, check the cab supports also. Its a good idea to make all repairs from the inside out.
|
![]() |
![]() |
![]() |
#6 |
Registered User
Join Date: Apr 2004
Location: Clanton, AL
Posts: 1,253
|
What is the best way to remove the old panels? Avaition snips / cutting wheel / ???
__________________
85' CUCV M1009!!! The newest addition! 6.2diesel, Th400, NP208, & only 36k miles! 70' C-10 LWB Fleetside - Looking good these days! ![]() 05' Dodge Neon 88' Winner Escape Sport 1750 - 4.3v6 94' Seadoo SP 84' Honda TRX200, bare nekkid. Just a frame & tires. Always looking for another project or any good deal! ![]() |
![]() |
![]() |
![]() |
#7 |
Account Suspended
Join Date: Sep 2000
Posts: 4,002
|
Cutting wheel for sure, you want to keep the metal that is staying nice and straight. Make sure you brace the cab accordingly if needed.
|
![]() |
![]() |
![]() |
#8 |
Registered User
Join Date: Apr 2004
Location: Clanton, AL
Posts: 1,253
|
Bracing the cab, as in welding a piece across a foot or so above the floor?
__________________
85' CUCV M1009!!! The newest addition! 6.2diesel, Th400, NP208, & only 36k miles! 70' C-10 LWB Fleetside - Looking good these days! ![]() 05' Dodge Neon 88' Winner Escape Sport 1750 - 4.3v6 94' Seadoo SP 84' Honda TRX200, bare nekkid. Just a frame & tires. Always looking for another project or any good deal! ![]() |
![]() |
![]() |
![]() |
Bookmarks |
Thread Tools | |
Display Modes | |
|
|