![]() |
Register or Log In To remove these advertisements. |
|
|
![]() |
|
Thread Tools | Display Modes |
![]() |
#1 |
Registered User
Join Date: Sep 2004
Location: Pleasanton, TX
Posts: 1,723
|
Well that is good to know but not quite what I was lookin for.
![]() Guess I'm on my own. |
![]() |
![]() |
![]() |
#2 |
Registered User
Join Date: Sep 2004
Location: Pleasanton, TX
Posts: 1,723
|
well now thats odd, posts swapped places??
![]() |
![]() |
![]() |
![]() |
#3 |
Registered User
Join Date: Dec 2002
Location: Tampa
Posts: 1,191
|
I've got a new cardboard one sitting in my garage. I can get you dimensions Sunday if you want. Send me a email/pm to remind me. I plan on building a sheetmetal one also.
__________________
'68 Short Step LS1/T56, Hydratech, Fatman Fabrications Stage III, Baer, Hot Rods to Hell, US Body, S&W, etc |
![]() |
![]() |
![]() |
#4 |
Registered User
Join Date: Sep 2004
Location: Pleasanton, TX
Posts: 1,723
|
Dimensions for glove box liner?
Thought it would be a fun little project to make my own glove box liner, since my 68 doesn't have one at all.
![]() Anyone happen to have the dimensions handy? Thanks ![]() ![]() |
![]() |
![]() |
![]() |
#5 |
Watch out for your cornhole !
![]() Join Date: Jun 2003
Location: Azle, Texas
Posts: 14,162
|
They are 10 bucks new.
That's all I personally need to know about them.
__________________
I'm on the Instagram- @Gearhead_Kevin |
![]() |
![]() |
![]() |
#6 |
Registered User
Join Date: Oct 2004
Location: saskatoon, planet earth
Posts: 686
|
LOL, tx.... well said
|
![]() |
![]() |
![]() |
#7 |
Registered User
Join Date: Dec 2002
Location: Tampa
Posts: 1,191
|
I think I can do better than a cardboard one, even if it is only 10 bucks.
__________________
'68 Short Step LS1/T56, Hydratech, Fatman Fabrications Stage III, Baer, Hot Rods to Hell, US Body, S&W, etc |
![]() |
![]() |
![]() |
#8 |
Registered User
Join Date: Sep 2004
Location: Pleasanton, TX
Posts: 1,723
|
68LSS1 sent me the dimensions, not bad "blueprints". Huge thanks to you bro.
![]() Went to the dollar store and picked up one of those pre-fabbed cardboard boxes, used for storage, etc; (stiff, compressed cardboard) and a tube of contact cement. Made the top, bottom and back all one piece with two end pieces. It's not perfect by any means but for 2 bucks I have a liner that will work fine for my daily driver. ![]() Now that I've done it I can someday fab one from fiberglass or sheet metal and something much more permanant. |
![]() |
![]() |
![]() |
#9 |
its all about the +6 inches
Join Date: Jan 2001
Location: Hilliard Ohio
Posts: 2,693
|
I made one out of sheet metal and it is awsome.
Just get an actual glove box liner...a crappy complete used one will work (That's what I used...a one dollar junk yard score) and trace it out on some thin sheet metal. I then used some air powere nibblers...i guess you could use a jig saw with proper blader. Paint it black and bent it up. Fight it into the hole and deive the screws into the metal with a screw driver tip on a cordless drill. You'll also want a thin rubber mat in there so the junk in there won't rattle over the bumps in the road. Here is a little bit of mine....no pics of the whole thing anymore. Last edited by Longhorn Man; 10-15-2004 at 10:17 PM. |
![]() |
![]() |
![]() |
#10 |
Account Suspended
Join Date: Dec 2003
Location: Texas
Posts: 2,686
|
Here is a pic of mine Homemade When I Was 16 With A 5" Hand Brake. If i could do it again I would use a large Siding Brake And Make It 10-8
Last edited by 1972C10; 07-02-2007 at 01:12 AM. |
![]() |
![]() |
![]() |
Bookmarks |
Thread Tools | |
Display Modes | |
|
|