how to install? - The 1947 - Present Chevrolet & GMC Truck Message Board Network

67ChevyC10Stepside · 10-25-2004, 11:06 PM

i bought 67-72 cab mounts from mothertruckers and they dont have any instructions with them....there are 2 rubbers with steel washers like bonded to them.....two almost identical that are all rubber.....2 cones with a little chunk out of each one......and 2 cones that curve in in the center then back out at the top and bottom....then there are 4 bolts 4 nuts and i think 2 big washers 2 smaller washers....and i think that's it.....(doing this from memory)

67ChevyC10Stepside · 10-26-2004, 07:05 PM

ttt

724wdcopper · 10-26-2004, 07:07 PM

do you have an LMC catalog? good for exploded views, but that's about it!

67ChevyC10Stepside · 10-26-2004, 08:36 PM

hmm....i dont have the square pieces as shown for the front ones...and i dont have number 14 and 20....they are made into the bushings.....now the only thing left to figure out is....is 15 or 21 the steel ones?

68w/sbc406 · 10-26-2004, 08:37 PM

67ChevyC10Stepside check your PM box

10-25-2004, 11:06 PM	#1
67ChevyC10Stepside Registered User Join Date: Mar 2004 Location: Butler PA Posts: 3,032	how to install? i bought 67-72 cab mounts from mothertruckers and they dont have any instructions with them....there are 2 rubbers with steel washers like bonded to them.....two almost identical that are all rubber.....2 cones with a little chunk out of each one......and 2 cones that curve in in the center then back out at the top and bottom....then there are 4 bolts 4 nuts and i think 2 big washers 2 smaller washers....and i think that's it.....(doing this from memory) __________________ 67 c-10, 400 SB, TH350, 4.10 gears, Blazer tank,camaro tach, sidemarker fuel fill (soon) WTB: stepside parts, 67 front end parts, 67 small window cab. posi for 3.73 or 4.10 for 12 bolt and 10 bolt.

10-26-2004, 07:05 PM	#2
67ChevyC10Stepside Registered User Join Date: Mar 2004 Location: Butler PA Posts: 3,032	ttt __________________ 67 c-10, 400 SB, TH350, 4.10 gears, Blazer tank,camaro tach, sidemarker fuel fill (soon) WTB: stepside parts, 67 front end parts, 67 small window cab. posi for 3.73 or 4.10 for 12 bolt and 10 bolt.

10-26-2004, 08:36 PM	#4
67ChevyC10Stepside Registered User Join Date: Mar 2004 Location: Butler PA Posts: 3,032	hmm....i dont have the square pieces as shown for the front ones...and i dont have number 14 and 20....they are made into the bushings.....now the only thing left to figure out is....is 15 or 21 the steel ones? __________________ 67 c-10, 400 SB, TH350, 4.10 gears, Blazer tank,camaro tach, sidemarker fuel fill (soon) WTB: stepside parts, 67 front end parts, 67 small window cab. posi for 3.73 or 4.10 for 12 bolt and 10 bolt.

10-26-2004, 08:37 PM	#5
68w/sbc406 Got Light Emitting Diode? Join Date: Apr 2004 Location: Newberg, OR Posts: 2,485	67ChevyC10Stepside check your PM box __________________ 1968 1/2 ton 2wd lwb 6 lug disc and bags up front. Next c notch and rear bags '02 Chevy Silverado LT ext cab short bed 2WD 5/7 drop on 22's(the family car) 1993 Cherokee work ride/weekend wheeler

Thread Tools
Show Printable Version Email this Page
Display Modes
Linear Mode Switch to Hybrid Mode Switch to Threaded Mode

10-26-2004, 07:07 PM	#3
724wdcopper graphic designer Join Date: May 2004 Location: Spokane, Washington Posts: 841	do you have an LMC catalog? good for exploded views, but that's about it!



Register or Log In To remove these advertisements.

Register or Log In To remove these advertisements.