lowrider exhaust - The 1947 - Present Chevrolet & GMC Truck Message Board Network

71/454 · 01-22-2005, 01:17 AM

I posted this in the pics area by mistake. So here goes again Does anyone have any pics of their exhaust in a lowered truck with leaf springs. Haven't got mine all the way down yet and it looks pretty tight with a five inch dump and a c notch, was wondering if I will have to cut the box floor for it. Any help is much appreciated thanks

68C15 · 01-22-2005, 08:45 AM

I dont have any pics of my set up yet. although mine is a coil spring type this idea may work for you. about the middle of trans area have the pipes come through a reinforced hole in frame & run them along outside of frame. then snake them above the axle between the wheel & frame & straight out the back.

2low72 · 01-22-2005, 04:03 PM

Here's mine, i don't rub on much, unless it's speed bump

crazy longhorn · 01-22-2005, 06:19 PM

Sorry, no pics on last summer's mods...... I have a 3/5 drop on my longhorn, & run full lenght Hooker comps. the old truck has 2 custom crossmembers,( 1 under the Richmond, & 1 under the rear of the cab). they are 2x6x1/4" wall, & notched for the pipes to run under. the truck runs a full lenght 2 1/2" dual system , that exits through the rear bumper(over the axle, & around the fuel cell), with 50's Flows for muffs. there is LOTS of room on a leaf spring truck to hang exhaust

my youngest "brat" helped with hanging the tailpipes on the longhorn, on a Sat afternoon. I have been the "part timer" in a local muffler shop for a couple seasons

crazyL

modifiedGMC · 01-22-2005, 08:47 PM

Quote:

Originally Posted by 68C15

I dont have any pics of my set up yet. although mine is a coil spring type this idea may work for you. about the middle of trans area have the pipes come through a reinforced hole in frame & run them along outside of frame. then snake them above the axle between the wheel & frame & straight out the back.

Coil set ups don't have as much room underneath to clear everything.That's the way I had mine, along the outside of the frame, when I had a big block. But now I have a small block and I'll probably still run them along the outer side of the frame just above the rubber snubber that way the suspension won't bottom out and they won't drag. Then when I lower it there won't be any problems. but for now they're turned out just in front of the rear wheels

special70gmc · 01-23-2005, 12:15 AM

heas some pic of mine

http://67-72chevytrucks.com/vboard/s....php3?t=122388

01-22-2005, 01:17 AM	#1
71/454 Turbo Guy Join Date: Jan 2005 Location: Calgary Alberta Posts: 353	lowrider exhaust I posted this in the pics area by mistake. So here goes again Does anyone have any pics of their exhaust in a lowered truck with leaf springs. Haven't got mine all the way down yet and it looks pretty tight with a five inch dump and a c notch, was wondering if I will have to cut the box floor for it. Any help is much appreciated thanks

01-22-2005, 08:45 AM	#2
68C15 blood type; Retumbo Join Date: Jan 2004 Location: next to my reloading bench Posts: 10,269	I dont have any pics of my set up yet. although mine is a coil spring type this idea may work for you. about the middle of trans area have the pipes come through a reinforced hole in frame & run them along outside of frame. then snake them above the axle between the wheel & frame & straight out the back. __________________ Man rule #77...if you own a 67 stepside with a caddy 472 you will never be in danger of loosing you man card

01-22-2005, 04:03 PM	#3
2low72 Registered User Join Date: Mar 2004 Location: Cheyenne, Wy Posts: 555	Here's mine, i don't rub on much, unless it's speed bump Attached Images __________________ 2014 GMC Yukon XL (Wifey's) 2004 Chevy Silverado Crew Cab Z71

01-22-2005, 06:19 PM	#4
crazy longhorn Fabricate till you "puke" Join Date: Jun 2002 Location: Ill Posts: 9,403	Sorry, no pics on last summer's mods...... I have a 3/5 drop on my longhorn, & run full lenght Hooker comps. the old truck has 2 custom crossmembers,( 1 under the Richmond, & 1 under the rear of the cab). they are 2x6x1/4" wall, & notched for the pipes to run under. the truck runs a full lenght 2 1/2" dual system , that exits through the rear bumper(over the axle, & around the fuel cell), with 50's Flows for muffs. there is LOTS of room on a leaf spring truck to hang exhaust my youngest "brat" helped with hanging the tailpipes on the longhorn, on a Sat afternoon. I have been the "part timer" in a local muffler shop for a couple seasons crazyL __________________ 69 longhorn,4" chop,3/5 drop, 1/2 ton suspension/disc brakes,1 1/2" body drop,steel tilt clip, 5.3/Edelbrock rpm intake/600 carb, Hooker streetrod shorties,2 1/2" exhaust/ H pipe/50's Flows , 6 spd Richmond trans,12 bolt/ 3.40 gears....

01-23-2005, 12:15 AM	#6
special70gmc Registered User Join Date: Sep 2002 Location: long island, new york Posts: 1,333	heas some pic of mine http://67-72chevytrucks.com/vboard/s....php3?t=122388 __________________ 1986 c-10 swb 5/7 drop 20'' coys 1958 belair 2door

Thread Tools
Show Printable Version Email this Page
Display Modes
Linear Mode Switch to Hybrid Mode Switch to Threaded Mode



Register or Log In To remove these advertisements.

Register or Log In To remove these advertisements.