How do I remove........... - The 1947 - Present Chevrolet & GMC Truck Message Board Network

jugernot · 03-11-2005, 04:47 PM

How do I remove the BOLT that holds the Panhard Bar to the differential? Is it pressed in and does it have to be pressed out? I have removed the nut holding the bolt in, but it won't move.

Alexis · 03-11-2005, 04:48 PM

i thought it was bolted in? on the front side of the diff.

edit:

i think it might be like a huge bolt you, so you might need vise grips to turn out......been to long since i took it out.

cdowns · 03-11-2005, 05:05 PM

when trying to remove the panhard bar the rear must not have weight on it because this will load the panhard

jugernot · 03-11-2005, 06:37 PM

I have removed everything off of the rear end, so I can have it blasted. I have removed the nut on differential panhard bolt, but it looks like it is pressed in. I even tried hitting it with a BFHm, but it did not seem to move. Anyone have any thoughts/ ideas?

Tx Firefighter · 03-11-2005, 08:23 PM

Twist it with a pipe wrench and it will pop right out. It's a taper fit.

03-11-2005, 04:47 PM	#1
jugernot Life, Be In It..... Join Date: Oct 2003 Location: Novato, California Posts: 1,498	How do I remove........... How do I remove the BOLT that holds the Panhard Bar to the differential? Is it pressed in and does it have to be pressed out? I have removed the nut holding the bolt in, but it won't move. __________________ Project Name: LEMON DROP. Reconstruction started "December 2000". Projected completion date "Who knows" http://67-72chevytrucks.com/vboard/s...d.php?t=200082 Last edited by jugernot; 03-11-2005 at 06:38 PM.

03-11-2005, 04:48 PM	#2
Alexis Member since 2000 Join Date: Dec 2000 Location: Mountain View Ca / Mexico Posts: 7,879	i thought it was bolted in? on the front side of the diff. edit: i think it might be like a huge bolt you, so you might need vise grips to turn out......been to long since i took it out. Last edited by Alexis; 03-11-2005 at 05:07 PM.

03-11-2005, 05:05 PM	#3
cdowns Senior Member Join Date: Jan 2003 Location: daytonabeach Posts: 22,956	when trying to remove the panhard bar the rear must not have weight on it because this will load the panhard __________________ 71c-10 350/2004r/4:11 lowered3/4 longbed/dead by hurricane MEANING OF DEATH::::: SOMEBODY ELSE GETS YOUR STUFF DONT BELIEVE EVERYTHING YOU THINK TAKE MY ADVISE;I DON'T USE IT ANYWAY

03-11-2005, 06:37 PM	#4
jugernot Life, Be In It..... Join Date: Oct 2003 Location: Novato, California Posts: 1,498	I have removed everything off of the rear end, so I can have it blasted. I have removed the nut on differential panhard bolt, but it looks like it is pressed in. I even tried hitting it with a BFHm, but it did not seem to move. Anyone have any thoughts/ ideas? __________________ Project Name: LEMON DROP. Reconstruction started "December 2000". Projected completion date "Who knows" http://67-72chevytrucks.com/vboard/s...d.php?t=200082

03-11-2005, 08:23 PM	#5
Tx Firefighter Watch out for your cornhole ! Join Date: Jun 2003 Location: Azle, Texas Posts: 14,162	Twist it with a pipe wrench and it will pop right out. It's a taper fit. __________________ I'm on the Instagram- @Gearhead_Kevin

Thread Tools
Show Printable Version Email this Page
Display Modes
Linear Mode Switch to Hybrid Mode Switch to Threaded Mode



Register or Log In To remove these advertisements.

Register or Log In To remove these advertisements.