Looking for patch panels... - The 1947 - Present Chevrolet & GMC Truck Message Board Network

'72 Chevy Suburban · 03-25-2005, 08:30 PM

No to sound too cheap here, but is there any chance that someone bought some patch panels and didn't end up using them? I need to order a bunch of them for my '72 Suburban. Imagine an Ohio truck that basically needs all of teh sheetmetal on the bottom of the truck... It's not exactly that bad, but I do need all of the rockers, wheel lips and quarter bottoms. The fenders and doors are ok. I also need some work on the driver's side floor near the rocker, so I assume that I'll need a patch for that too.

Can anyone confirm which "bedside" or suburban patch that I would need for the quarters? I have read some different suggestions for this.

Thanks,

c-1072 · 03-25-2005, 08:52 PM

ccgTruck .com I think they are in ohio . Might save you the shipping cost i talked with the guy he sounded like he knows his stuff .

lngbed71 · 03-26-2005, 09:33 AM

Check with GMC Paul's too

lngbed71 · 03-26-2005, 09:35 AM

http://www.gmcpauls.com/

'72 Chevy Suburban · 03-26-2005, 09:44 AM

Thanks guys...

I usually buy from Paul and have had only good experiences there. I am also pretty excited that the third door rocker is now available through him.

bagged91 · 03-26-2005, 03:14 PM

I am currently redoing an Ohio burb, Have fun

I am lucky enough that I have another burb to use for the inner braces, wheel tubs, ect...

As far as the patch panels go...

Your best bet would be to order the burb lower patches & the rockers. Keep in mind that the pass side P/U rocker is different than the pass side front door rocker. You will need to modify the p/u rocker to work but it can be done.

For the wheel arch, while not the cheapest way to do it, you will need a pair of SWB bedsides. The SWB bedsides have the correct bead in the lip as well as the correct shape at the leading edge of the arch(more squared off). The LWB bedsides are shaped somewhat different at the leading edge of the arch(more rounded). The pass side swb bedside can be used to go into the doorjamb and to the rocker but you will need to make a "pichweld" for the bottom. The drivers side you will need to have the lower panel from the wheel well to behind the front door fabricated.

4x4Poet · 03-28-2005, 08:26 AM

Good info, Bagged. For my K10 burb, I just bought some blazer lower panels that go from the rear wheelwell foward. First look seems to be right, but I've yet to install them. The pass side goes from the wheelwell to the 3rd door. The driver's side goes only 2/3 of the way to the driver's door. I'll try to post here once I actually weld them in next week. I won't be sure till then.

bagged91 · 03-28-2005, 06:27 PM

Yeah, I was looking at them too. They seem to have a more pronounced bead on them than the upper wheel arch does. Wish they would get it together and just make full replacement 1/4's for the burb/panel.

Sure would make life easier than welding in 42 different patches! lol...

MARIOS68PANEL · 04-03-2005, 05:08 PM

I just did my lower rear corner this weekend. What a nightmare! 1/2 in. too long over all. When you line up the wheel well the thing sticks out 1/2 in past the tail and same the other way. Had to cut the new panel and bend it around. Definatly not the perfect fit I was hoping for. but I did get it on.

03-25-2005, 08:30 PM	#1
'72 Chevy Suburban Chevy's Rock! Join Date: Apr 2004 Location: Lebanon, OH Posts: 448	Looking for patch panels... No to sound too cheap here, but is there any chance that someone bought some patch panels and didn't end up using them? I need to order a bunch of them for my '72 Suburban. Imagine an Ohio truck that basically needs all of teh sheetmetal on the bottom of the truck... It's not exactly that bad, but I do need all of the rockers, wheel lips and quarter bottoms. The fenders and doors are ok. I also need some work on the driver's side floor near the rocker, so I assume that I'll need a patch for that too. Can anyone confirm which "bedside" or suburban patch that I would need for the quarters? I have read some different suggestions for this. Thanks, __________________ John '59 NAPCO Pickup '70 K10 Pickup 350 '72 C20 Suburban 350 (MIA) '57 Chieftain 455 '68 Firebird Convertible - 400 '68 Catalina Convertible - 400 '85 Vette

03-25-2005, 08:52 PM	#2
c-1072 Registered User Join Date: Sep 2004 Location: rochester NY Posts: 777	parts ccgTruck .com I think they are in ohio . Might save you the shipping cost i talked with the guy he sounded like he knows his stuff .

03-26-2005, 09:33 AM	#3
lngbed71 Nothing fits but the oil Join Date: Mar 2003 Location: Gaston, Indiana Posts: 424	Check with GMC Paul's too __________________ Land of the free Because of the brave

03-26-2005, 09:35 AM	#4
lngbed71 Nothing fits but the oil Join Date: Mar 2003 Location: Gaston, Indiana Posts: 424	http://www.gmcpauls.com/ __________________ Land of the free Because of the brave

03-26-2005, 09:44 AM	#5
'72 Chevy Suburban Chevy's Rock! Join Date: Apr 2004 Location: Lebanon, OH Posts: 448	Thanks guys... I usually buy from Paul and have had only good experiences there. I am also pretty excited that the third door rocker is now available through him. __________________ John '59 NAPCO Pickup '70 K10 Pickup 350 '72 C20 Suburban 350 (MIA) '57 Chieftain 455 '68 Firebird Convertible - 400 '68 Catalina Convertible - 400 '85 Vette

03-26-2005, 03:14 PM	#6
bagged91 Out draggin' Join Date: Jan 2004 Location: Pitman,NJ Posts: 1,574	I am currently redoing an Ohio burb, Have fun I am lucky enough that I have another burb to use for the inner braces, wheel tubs, ect... As far as the patch panels go... Your best bet would be to order the burb lower patches & the rockers. Keep in mind that the pass side P/U rocker is different than the pass side front door rocker. You will need to modify the p/u rocker to work but it can be done. For the wheel arch, while not the cheapest way to do it, you will need a pair of SWB bedsides. The SWB bedsides have the correct bead in the lip as well as the correct shape at the leading edge of the arch(more squared off). The LWB bedsides are shaped somewhat different at the leading edge of the arch(more rounded). The pass side swb bedside can be used to go into the doorjamb and to the rocker but you will need to make a "pichweld" for the bottom. The drivers side you will need to have the lower panel from the wheel well to behind the front door fabricated. __________________ 91 GMC Xcab LB-Bags/bd/caddy clip SOLD 72 C10 Cheyenne Super LWB SOLD 92 GMC K1500 Burb 72 C10 Burb (ex. Cheesewagon)SOLD 72 C20 Burb parts truck 71 C10 Burb "project"

03-28-2005, 08:26 AM	#7
4x4Poet Registered User Join Date: Nov 2004 Location: "Under Montana skies." Posts: 1,836	Good info, Bagged. For my K10 burb, I just bought some blazer lower panels that go from the rear wheelwell foward. First look seems to be right, but I've yet to install them. The pass side goes from the wheelwell to the 3rd door. The driver's side goes only 2/3 of the way to the driver's door. I'll try to post here once I actually weld them in next week. I won't be sure till then. __________________ '71 GMC K20 Suburban, '71 GMC K10 Suburban, '72 Chevy C10 CST Suburban, '72 Chevy K20 clunker pickup.

03-28-2005, 06:27 PM	#8
bagged91 Out draggin' Join Date: Jan 2004 Location: Pitman,NJ Posts: 1,574	Yeah, I was looking at them too. They seem to have a more pronounced bead on them than the upper wheel arch does. Wish they would get it together and just make full replacement 1/4's for the burb/panel. Sure would make life easier than welding in 42 different patches! lol... __________________ 91 GMC Xcab LB-Bags/bd/caddy clip SOLD 72 C10 Cheyenne Super LWB SOLD 92 GMC K1500 Burb 72 C10 Burb (ex. Cheesewagon)SOLD 72 C20 Burb parts truck 71 C10 Burb "project"

04-03-2005, 05:08 PM	#9
MARIOS68PANEL Active Member Join Date: Mar 2005 Location: North Highlands. California Posts: 449	I just did my lower rear corner this weekend. What a nightmare! 1/2 in. too long over all. When you line up the wheel well the thing sticks out 1/2 in past the tail and same the other way. Had to cut the new panel and bend it around. Definatly not the perfect fit I was hoping for. but I did get it on. __________________ 67 short step 71 Custom

Thread Tools
Show Printable Version Email this Page
Display Modes
Linear Mode Switch to Hybrid Mode Switch to Threaded Mode



Register or Log In To remove these advertisements.

Register or Log In To remove these advertisements.