|
04-29-2005, 12:48 AM
|
#1 |
|
I need another Barley Pop
Join Date: Feb 2001
Location: Grants Pass, OR
Posts: 1,629
|
Front axle clean-up
Haven't posted in a long time, thought I would post a pic of the front axle clean-up last weekend.
__________________
67 Short Fleet 4x4 04 Honda CRF450R 89 Toyota 4-Runner 34 Ford 2 door sedan - Long term project ---------------------------------------------- There is a very fine line between "hobby" and "mental illness" 
|
|
|
|
04-29-2005, 01:17 AM
|
#2 |
|
Professional Grade
Join Date: May 2003
Location: Fort McMurray, Alberta
Posts: 7,915
|
Lookin good as always!!
__________________
1995 Chevrolet 2 Door Tahoe (6.6L LBZ Duramax / ZF6 / NP241 with 1 ton solid axle swap) |
|
|
|
|
04-29-2005, 08:05 AM
|
#3 |
|
Registered User
 
Join Date: Feb 2001
Location: East Central, MO
Posts: 11,336
|
Looks good Pont........
|
|
|
|
|
04-29-2005, 10:39 AM
|
#4 |
|
Post Whore
Join Date: Feb 2000
Location: Rose Hill, KS, USA
Posts: 12,686
|
Good to see you. Truck looks great as usual.
What attaches to what look like receivers on each side of the license plate?
__________________
1970 Blazer with a 400 sbc and 4" lift 1980 Pontiac Trans Am, 455 Oldsmobile 2012 Kawasaki Concours 14 |
|
|
|
|
05-01-2005, 01:22 PM
|
#5 |
|
Senior Member
Join Date: Apr 2000
Location: madison indiana
Posts: 3,836
|
clean setup... not tell us about the xover setup..
__________________
jamie72 72 BB cheyenne -- Restoration getting started.. member #807 http://www.myspace.com/whitetailobsession www.antlertalk.com |
|
|
|
|
05-02-2005, 05:50 PM
|
#6 |
|
Registered User
Join Date: Feb 2005
Location: Lake Crystal, MN
Posts: 656
|
Power Steering on that beast? Looks great, was the diff cover expensive?
__________________
-Cory 1967 2 Wheel Chevy |
|
|
|
|
05-03-2005, 06:21 PM
|
#7 |
|
Registered User
Join Date: Jun 2003
Location: spokane wa
Posts: 2,189
|
Pont.... Where's the front drive shaft
__________________
Support The Board |
|
|
|
|
05-03-2005, 10:03 PM
|
#8 |
|
I need another Barley Pop
Join Date: Feb 2001
Location: Grants Pass, OR
Posts: 1,629
|
Thanks everyone.
Yukon, hard to say what those receiver looking things are where the front bumper has been cut. When I got the truck, it had a skidplate and brushguard covering all of that area. One of these days I'll get around to cutting that crap out and replacing the front bumper. Jamie, PM me and I'll tell ya all I know about crossover steering (it isn't much). 1STtimePRo, it definitely has power steering. The diff cover was cheap at a local parts store (about $15). It's just something to use until I can afford a TA aluminum diff cover. I like the looks of their cover...... Drink, you would have to notice that!  Too much angle of the dangle. I need to either get creative with CV joints on the front shaft or just spring the $$$$ to flip the diff and run reverse rotation. Haven't decided yet which way I'm gonna go. Thanks for pointing out that the trucks a 2 wheeler though! 
__________________
67 Short Fleet 4x4 04 Honda CRF450R 89 Toyota 4-Runner 34 Ford 2 door sedan - Long term project ---------------------------------------------- There is a very fine line between "hobby" and "mental illness"
|
|
|
|
|
05-03-2005, 11:12 PM
|
#9 |
|
Registered User
Join Date: Jun 2003
Location: spokane wa
Posts: 2,189
|
I'm here for you buddy.
But dam I will say I can only try to have a truck as clean and nice as yours.. Does that help
__________________
Support The Board |
|
|
|
 |
| Bookmarks |
| Thread Tools | |
| Display Modes | |
|
|
Linear Mode
