Need Help!! - The 1947 - Present Chevrolet & GMC Truck Message Board Network

2low72 · 08-02-2005, 02:52 PM

I threw out my carrier bearing yesterday! Today I have the drive shaft out and the bearing itself will not come off. What do ya'll do to get this thing off?
Thanks

355 · 08-02-2005, 03:49 PM

I had to take off the yoke and use a punch drift and a 2# shop hammer. Get down on the race and drift it off, once it starts to move it will keep goin. Put some type of Neversieze on the shaft for the new one and it will be more better the next time.

70GMC_BOB · 08-02-2005, 04:24 PM

I took mine to a mmachine shop. they just pressed the old piece off and the new bearing on. I fought it with a hammer as well. I could have save an hour if I had just gone straight to the shop.

ClayMore_5by5 · 08-02-2005, 11:16 PM

As a last resort, you could try det cord or C-4. It'll come flying off of there like a bat!! It will also feel real good up until the point you realize how damage you've done to the rest of the vehicle (Not to mention, blowing a hole in your concrete).

Would you believe that some people think I over-react when I get angry?? Go Figure!

Longhorn Man · 08-02-2005, 11:44 PM

I say take it to a drive line shop. IMO, it isn't worth bleeding over. (don't ask)

08-02-2005, 02:52 PM	#1
2low72 Registered User Join Date: Mar 2004 Location: Cheyenne, Wy Posts: 555	Need Help!! I threw out my carrier bearing yesterday! Today I have the drive shaft out and the bearing itself will not come off. What do ya'll do to get this thing off? Thanks __________________ 2014 GMC Yukon XL (Wifey's) 2004 Chevy Silverado Crew Cab Z71

08-02-2005, 03:49 PM	#2
355 Registered User Join Date: May 2005 Location: South Mississippi Posts: 81	I had to take off the yoke and use a punch drift and a 2# shop hammer. Get down on the race and drift it off, once it starts to move it will keep goin. Put some type of Neversieze on the shaft for the new one and it will be more better the next time. __________________ 1969 C10 Long Step,355,700r4w/lockup, HEI,Weiand,750 Performer,1.6 rockers,Camel Humps,Comp 262Extreme,Hedman,2 1/2"pipes, tele/tilt,SunRoof,ps,Disc pb,ac,Cragar,eaton,Corvette style roll pan, Bowtie louvered tail gate,lowered 2/2.

08-02-2005, 04:24 PM	#3
70GMC_BOB Registered User Join Date: Jul 2001 Location: Lynnwood, washington Posts: 121	I took mine to a mmachine shop. they just pressed the old piece off and the new bearing on. I fought it with a hammer as well. I could have save an hour if I had just gone straight to the shop. __________________ 1972 chev c20 2wd lwb 350v8/th350. (dad's)1970 gmc longstep (9ft commercial bed), 1 ton, 2wd, 350/th400.

08-02-2005, 11:16 PM	#4
ClayMore_5by5 Registered User Join Date: Jun 2005 Location: Clever, Missouri Posts: 32	As a last resort, you could try det cord or C-4. It'll come flying off of there like a bat!! It will also feel real good up until the point you realize how damage you've done to the rest of the vehicle (Not to mention, blowing a hole in your concrete). Would you believe that some people think I over-react when I get angry?? Go Figure! __________________ '72 C-10 Deluxe '74 Porsche 914 (Skateboard on Meth) '76 Harley XL (Another project) Combat Zen: There is no problem in this world too great or too small that cannot be solved through a careful application of high explosives.

Thread Tools
Show Printable Version Email this Page
Display Modes
Linear Mode Switch to Hybrid Mode Switch to Threaded Mode

08-02-2005, 11:44 PM	#5
Longhorn Man its all about the +6 inches Join Date: Jan 2001 Location: Hilliard Ohio Posts: 2,690	I say take it to a drive line shop. IMO, it isn't worth bleeding over. (don't ask)



Register or Log In To remove these advertisements.

Register or Log In To remove these advertisements.