Gettin to the fender Emblem.. - The 1947 - Present Chevrolet & GMC Truck Message Board Network

SWINGSAX68 · 06-26-2002, 03:54 PM

I want to remove the fender emblem on my 68(

/10) without having to take of the whole fender...can I just take out the fender well and reach in to unscrew it? I just want to take it off and clean it up, and put some nice red paint on the bowtie. And leave it off until I get the paint on. LET ME KNOW!!!!!!!

Low69CST · 06-26-2002, 04:02 PM

If you really wanna get it off your best bet would be to drop the fenderwell down. You should be able to get to fine then. You could just tape up the fender itsself around the emblem and clean it up without taking it off. Line the fender good with paper so you won't get any mess on it.

SWINGSAX68 · 06-26-2002, 05:34 PM

ok....So say I unscrew the bolts from the outside edge of the fender well, what other bolts are there to take off? Will it just come right down, will I be able to remove the well with the wheels on? thanks!!!!!!!!!!!

Super Chevy · 06-26-2002, 05:48 PM

i think you might juse be able to pull the cowl off,its infront of the cab,behind the hood,its held on by like 6 bolts...

SC

bigvinnie · 06-26-2002, 06:14 PM

removing the cowl won't be enough..... you'll have to remove the bolts where the fender lip meets the inner fender, all the way to the bottom rear edge of the fender.... then loosen the ones at the core support and the large one where it bolts to the cab and you should be able to access the emblems...

HvyChevy454 · 06-26-2002, 06:47 PM

if your talkin about the ones by the door to get em off you have to remove the fender well and i am able to get if off w/ the 235/70 15's still on. putting it back on is another story i had to loosen up the back portion of the quarter panel and have my dad pull out on while i stuck my hand up in there to start the new threads. besides taking the fender wells out is no big that is the 1st thing i do when i have to do any work in the engine bay b/c it gives you so much more room to move around.

06-26-2002, 03:54 PM	#1
SWINGSAX68 Now the others dig........ Join Date: May 2002 Location: San Antonio, TX Posts: 1,520	Gettin to the fender Emblem.. I want to remove the fender emblem on my 68(/10) without having to take of the whole fender...can I just take out the fender well and reach in to unscrew it? I just want to take it off and clean it up, and put some nice red paint on the bowtie. And leave it off until I get the paint on. LET ME KNOW!!!!!!! __________________ 68 Chevy C10 Stepside Black Primer 78 GMC Longbed White 09 Chevy Silverado Shortbed Granite Blue *LOOKING FOR A 67 4 DOOR IMPALA!!!Just like Sam and Dean Winchester!! 'Cause Mustangs are for p^#$ and you can fit a body in the trunk of a 67 Impala* MEMBER OF THE DRUM BRAKE CLUB Bachelor of Music in Jazz Studies Texas State University-San Marcos, TX Certified Music Educator I hope Mom is up there watching and being my Guardian Angel "I've got a fever.....and the only prescription.....IS MORE COW BELL" -The Legendary: Bruce Dickenson "F#$@ 'em up!!!!!!" -The Legendary: Rogelio Escobar TRUCKY LINKS** http://67-72chevytrucks.com/vboard/s...d.php?t=457750 http://67-72chevytrucks.com/vboard/s...d.php?t=461184 http://67-72chevytrucks.com/vboard/s...d.php?t=472848 http://67-72chevytrucks.com/vboard/s...d.php?t=417541 http://67-72chevytrucks.com/vboard/s...d.php?t=477788

06-26-2002, 04:02 PM	#2
Low69CST Registered User Join Date: May 2000 Location: Frankfort, Kentucky, USA Posts: 2,163	If you really wanna get it off your best bet would be to drop the fenderwell down. You should be able to get to fine then. You could just tape up the fender itsself around the emblem and clean it up without taking it off. Line the fender good with paper so you won't get any mess on it. __________________ '69 CST Short fleetside Lowered, 400 small block, 700R4, 4 wheel disc brakes, front sway bar & rear camaro sway bar (in progress) '87 V10 4x4 Short Fleetside Quad Suspension and Dual Tanks

06-26-2002, 05:34 PM	#3
SWINGSAX68 Now the others dig........ Join Date: May 2002 Location: San Antonio, TX Posts: 1,520	drop well ok....So say I unscrew the bolts from the outside edge of the fender well, what other bolts are there to take off? Will it just come right down, will I be able to remove the well with the wheels on? thanks!!!!!!!!!!! __________________ 68 Chevy C10 Stepside Black Primer 78 GMC Longbed White 09 Chevy Silverado Shortbed Granite Blue *LOOKING FOR A 67 4 DOOR IMPALA!!!Just like Sam and Dean Winchester!! 'Cause Mustangs are for p^#$ and you can fit a body in the trunk of a 67 Impala* MEMBER OF THE DRUM BRAKE CLUB Bachelor of Music in Jazz Studies Texas State University-San Marcos, TX Certified Music Educator I hope Mom is up there watching and being my Guardian Angel "I've got a fever.....and the only prescription.....IS MORE COW BELL" -The Legendary: Bruce Dickenson "F#$@ 'em up!!!!!!" -The Legendary: Rogelio Escobar TRUCKY LINKS** http://67-72chevytrucks.com/vboard/s...d.php?t=457750 http://67-72chevytrucks.com/vboard/s...d.php?t=461184 http://67-72chevytrucks.com/vboard/s...d.php?t=472848 http://67-72chevytrucks.com/vboard/s...d.php?t=417541 http://67-72chevytrucks.com/vboard/s...d.php?t=477788

06-26-2002, 06:14 PM	#5
bigvinnie Registered User Join Date: Aug 2001 Location: escondido, ca 92026 Posts: 1,222	removing the cowl won't be enough..... you'll have to remove the bolts where the fender lip meets the inner fender, all the way to the bottom rear edge of the fender.... then loosen the ones at the core support and the large one where it bolts to the cab and you should be able to access the emblems... __________________ '72 short step, 350, 700R4, tilt, ps, pdb, a/c, lowered coils, etc., other work in progress... San Diego, CA 72 Stepside Project

06-26-2002, 06:47 PM	#6
HvyChevy454 Slowly getting CRSS... Join Date: Jul 2001 Location: Lutz, Florida Posts: 656	if your talkin about the ones by the door to get em off you have to remove the fender well and i am able to get if off w/ the 235/70 15's still on. putting it back on is another story i had to loosen up the back portion of the quarter panel and have my dad pull out on while i stuck my hand up in there to start the new threads. besides taking the fender wells out is no big that is the 1st thing i do when i have to do any work in the engine bay b/c it gives you so much more room to move around. __________________ -Nic Lutz, Fl My Team Website The Heavy Chevy Website ------------------ 72 Cheyenne 10 LWB GM 12-bolt 3.08 w/ Auburn Posi 91 454 Edel Performer RPM Intake 750 cfm carb Comp Cam 268/.495 Hedman Headers Dual 3'' Exhaust 71 Cheyenne 20 4x4 Fact. A/C PS PB Tilt Currently in the works... Speak Softly and Carry A Big Block... There is No replacement for Displacement... "If everything seems under control, you're just not going fast enough." - Mario Andretti

06-26-2002, 05:48 PM	#4
Super Chevy Registered User Join Date: Feb 2001 Location: Ohio Posts: 1,025	i think you might juse be able to pull the cowl off,its infront of the cab,behind the hood,its held on by like 6 bolts... SC

Thread Tools
Show Printable Version Email this Page
Display Modes
Linear Mode Switch to Hybrid Mode Switch to Threaded Mode



Register or Log In To remove these advertisements.

Register or Log In To remove these advertisements.