Leveling out my truck - The 1947 - Present Chevrolet & GMC Truck Message Board Network

bigcarguy · 06-30-2002, 10:07 AM

I have a 72 C10 1/2 ton that sits haunched at the front (the bed sits higher than the front). Anyways, I wanted to level it out so the bed and the front are the same height. I want to lift it so this isn't a lowering question. Would springs from a 3/4ton level it out or is there more that needs to be done? Also, I know this question is probably asked all the time, but what is the widest rim I can put on it with no mods? Thanks for the input.

72chevyLWB · 07-01-2002, 08:28 PM

Is it a leaf spring truck? If it is just start adding leafs until you get it level. I dropped mine too far, so I started pulling and adding leafs until i got it level. If you want to see what 3/4 ton springs would do, just look and measure one.

bigcarguy · 07-01-2002, 11:08 PM

nope, coil springs

bigvinnie · 07-02-2002, 04:45 AM

I guess I'd go for new front coils if yours are old and see how much height I picked up..... how much height difference are we talking about here...???

bigcarguy · 07-02-2002, 09:47 AM

There's not a huge difference, but the bed is noticably higher than the front. I know alot of trucks look like that anyway, but I personally prefer the level look.

*67Fleetsidedream* · 07-03-2002, 07:22 AM

My truck did the same thing when I first got mine. Easy fix. Get some new coils for the front. If your truck came originally with a 6 cylinder and then was replaced with a v-8 then most likely you have 6 cylinder springs. That was the situation with mine.

Ben

stllookn · 07-05-2002, 04:57 PM

Most of the trucks come stock about 1-2 inches higher in the rear because the springs are stiffer and when loaded they will drop some. When they are loaded to capacity they are lower in the rear. If you want it to ride level in the unloaded condition then you need to raise the front with stiffer springs (3/4 ton) or put softer springs in the rear. I would go for the softer springs in the rear or just load some sand bags in the back...cheapest way to go. Drive if like that for a few months and see what you think.

06-30-2002, 10:07 AM	#1
bigcarguy Finally a Bulldawg Join Date: Apr 2001 Location: Athens, Georgia Posts: 220	Leveling out my truck I have a 72 C10 1/2 ton that sits haunched at the front (the bed sits higher than the front). Anyways, I wanted to level it out so the bed and the front are the same height. I want to lift it so this isn't a lowering question. Would springs from a 3/4ton level it out or is there more that needs to be done? Also, I know this question is probably asked all the time, but what is the widest rim I can put on it with no mods? Thanks for the input.

07-01-2002, 08:28 PM	#2
72chevyLWB Got 20's???? Join Date: Oct 2001 Location: Aberdeen SD Posts: 1,451	Is it a leaf spring truck? If it is just start adding leafs until you get it level. I dropped mine too far, so I started pulling and adding leafs until i got it level. If you want to see what 3/4 ton springs would do, just look and measure one. __________________ 99 Silverado Ex-Cab 2wd, Bagged&WhippleCharged 02 Sierra Ex-Cab 4wd 2500 HD The 72 went down the road.

07-02-2002, 04:45 AM	#4
bigvinnie Registered User Join Date: Aug 2001 Location: escondido, ca 92026 Posts: 1,222	I guess I'd go for new front coils if yours are old and see how much height I picked up..... how much height difference are we talking about here...??? __________________ '72 short step, 350, 700R4, tilt, ps, pdb, a/c, lowered coils, etc., other work in progress... San Diego, CA 72 Stepside Project

07-05-2002, 04:57 PM	#7
stllookn Saving 1 truck at a time! Join Date: Aug 2001 Location: Kent, WA Posts: 6,465	Most of the trucks come stock about 1-2 inches higher in the rear because the springs are stiffer and when loaded they will drop some. When they are loaded to capacity they are lower in the rear. If you want it to ride level in the unloaded condition then you need to raise the front with stiffer springs (3/4 ton) or put softer springs in the rear. I would go for the softer springs in the rear or just load some sand bags in the back...cheapest way to go. Drive if like that for a few months and see what you think. __________________ '68 C20 Longhorn 50th Anniversary 400/TH400 '68 C20 Longhorn 50th Anniversary 468/TH400w/buckets '72 C20 Halfhorn (Longhorn w/o cab and front clip) '69 Flxible Cruiser (look up ugly in the dictionary) Last edited by stllookn; 07-05-2002 at 04:59 PM.

Thread Tools
Show Printable Version Email this Page
Display Modes
Linear Mode Switch to Hybrid Mode Switch to Threaded Mode

07-01-2002, 11:08 PM	#3
bigcarguy Finally a Bulldawg Join Date: Apr 2001 Location: Athens, Georgia Posts: 220	nope, coil springs

07-02-2002, 09:47 AM	#5
bigcarguy Finally a Bulldawg Join Date: Apr 2001 Location: Athens, Georgia Posts: 220	There's not a huge difference, but the bed is noticably higher than the front. I know alot of trucks look like that anyway, but I personally prefer the level look.

07-03-2002, 07:22 AM	#6
67Fleetsidedream Wiseass secured himself a BAN Join Date: Nov 2000 Location: MOON!!! Posts: 2,282	My truck did the same thing when I first got mine. Easy fix. Get some new coils for the front. If your truck came originally with a 6 cylinder and then was replaced with a v-8 then most likely you have 6 cylinder springs. That was the situation with mine. Ben



Register or Log In To remove these advertisements.

Register or Log In To remove these advertisements.