drop spindles conformation - The 1947 - Present Chevrolet & GMC Truck Message Board Network

68 short step · 01-01-2006, 12:17 PM

can someone please confirm that these will indeed fit a 68 c10 ball joint/ tie rod ends and it also is a 2" drop.. i searched but to no luck thanks

68 short step · 01-01-2006, 12:18 PM

guess this would help
http://cgi.ebay.com/ebaymotors/ws/eB...RK%3AMEWN%3AIT

**Tim Christian** · 01-01-2006, 02:58 PM

If I was going to give that for them I would go ahead and buy new.

68 short step · 01-01-2006, 03:18 PM

ive been lookin for awhile now for some 2" drop spindles, not 2.5 or 3" and had no luck. i know for about 40$ more + shipping i could of bought a new set of 2.5" spindles.
Tim could you send a pic of this, DG009 69-72 Complete Dash Gauge cluster, to donhulse@sbcglobal.net

Tx Firefighter · 01-01-2006, 04:17 PM

I'm pretty sure that's a 3 inch drop spindle. BellTech part number is 3800 in the picture. The "3" is the 3 inch drop. Example, my Blazer has 3 inch drop Belltech spindles, part number 3100.

I looked everywhere on the internet though and can't find the 3800 part number to confirm. All I can find is the 3120, which fits 71-72 only. I can't find any Belltech application that's older than 71.

01-01-2006, 12:17 PM	#1
68 short step Senior Member Join Date: Aug 2005 Location: tulsa OK Posts: 3,070	drop spindles conformation can someone please confirm that these will indeed fit a 68 c10 ball joint/ tie rod ends and it also is a 2" drop.. i searched but to no luck thanks

01-01-2006, 12:18 PM	#2
68 short step Senior Member Join Date: Aug 2005 Location: tulsa OK Posts: 3,070	Re: drop spindles conformation guess this would help http://cgi.ebay.com/ebaymotors/ws/eB...RK%3AMEWN%3AIT

01-01-2006, 02:58 PM	#3
Tim Christian Senior Member Join Date: Dec 1999 Location: TN/VA Posts: 6,388	Re: drop spindles conformation If I was going to give that for them I would go ahead and buy new.

01-01-2006, 03:18 PM	#4
68 short step Senior Member Join Date: Aug 2005 Location: tulsa OK Posts: 3,070	Re: drop spindles conformation ive been lookin for awhile now for some 2" drop spindles, not 2.5 or 3" and had no luck. i know for about 40$ more + shipping i could of bought a new set of 2.5" spindles. Tim could you send a pic of this, DG009 69-72 Complete Dash Gauge cluster, to donhulse@sbcglobal.net

01-01-2006, 04:17 PM	#5
Tx Firefighter Watch out for your cornhole ! Join Date: Jun 2003 Location: Azle, Texas Posts: 14,162	Re: drop spindles conformation I'm pretty sure that's a 3 inch drop spindle. BellTech part number is 3800 in the picture. The "3" is the 3 inch drop. Example, my Blazer has 3 inch drop Belltech spindles, part number 3100. I looked everywhere on the internet though and can't find the 3800 part number to confirm. All I can find is the 3120, which fits 71-72 only. I can't find any Belltech application that's older than 71. __________________ I'm on the Instagram- @Gearhead_Kevin Last edited by Tx Firefighter; 01-01-2006 at 04:20 PM.

Thread Tools
Show Printable Version Email this Page
Display Modes
Linear Mode Switch to Hybrid Mode Switch to Threaded Mode



Register or Log In To remove these advertisements.

Register or Log In To remove these advertisements.