|
02-05-2006, 06:41 PM
|
#1 |
|
Account Suspended
Join Date: Dec 2005
Location: martin georgia
Posts: 568
|
73' on a 69'?
hi,
i was wondering if i could take the 5 lug front and rear end out of a 73' c10 and put it under a 69' c10? will this work? |
|
|
|
02-05-2006, 09:10 PM
|
#2 |
|
Happy to be here
 
Join Date: Mar 2000
Location: Cypress, TX
Posts: 39,023
|
Re: 73' on a 69'?
Yes and maybe! You can do the entire front crossmember swap with no problem. I should say minimal trouble. You will have to mod the brake lines since they come in differently.
The rear is a maybe. It won't bolt in unless your 69 has leaf springs. If I remember correctly all 69's were coil spring rears (assuming you are talking about a 2wd). You can modify the mounts to work, but there still might be a catch. I think it was 69-70 that had two different width rear ends. You will need to verify that the rear ends are the same width.... 
__________________
Follow me on Facebook and Instagram @N2trux.com Articles- "Jake" the 84 to 74 crewcab "Elwood" the77_Remix 85 GMC Sierra "Scarlett" "Refining Sierra" Last edited by N2TRUX; 02-05-2006 at 09:10 PM. |
|
|
|
|
02-05-2006, 09:56 PM
|
#3 |
|
Account Suspended
Join Date: Dec 2005
Location: martin georgia
Posts: 568
|
Re: 73' on a 69'?
ok, i have the coil springs. thats good news. and its 2wd, any special (kit) i can buy to modify the brake lines?
Last edited by 1969owner; 02-05-2006 at 09:57 PM. |
|
|
|
|
02-05-2006, 10:06 PM
|
#4 |
|
Account Suspended
Join Date: Dec 2005
Location: martin georgia
Posts: 568
|
Re: 73' on a 69'?
brain fart. ill just get the frontend, buy six lug rotors, not mess with the rearend!
|
|
|
|
|
02-05-2006, 10:07 PM
|
#5 |
|
Registered User
Join Date: Jan 2002
Location: Slippery Rock PA USA
Posts: 1,692
|
Re: 73' on a 69'?
u can do it one of 2 ways...you can swap the whole thing..belly pan and all or just swap the spindles ..rotors..calipers..brake hoses and steering linkage...and you'll have to buy new ball joints ...and i would just run new brake lines in the front........
__________________
Ken Lyons, Slippery rock pa 68 short step 327 t10 4 gear 72 2wd blazer project 70 lwb 305/700r driver 78 caprice project 02 cavalier D.D ( hate it!!) |
|
|
|
|
02-05-2006, 10:16 PM
|
#6 |
|
Account Suspended
Join Date: Dec 2005
Location: martin georgia
Posts: 568
|
Re: 73' on a 69'?
ok
|
|
|
|
|
02-05-2006, 11:26 PM
|
#7 |
|
Senior Member
Join Date: Sep 2004
Location: CANADA
Posts: 1,681
|
Re: 73' on a 69'?
the 73+ rear ends.are all leafs,you could cut the mounting pads off the old one and weld them to the 73+ rear.The only problem is the panard bar(track bar)the 73+ rears do not have a place to bolt them on.Find a 71-72 rear and bolt in.or pull the 6 bolt axles and have them re-drilled with the 5 lug pattern
|
|
|
|
|
02-05-2006, 11:52 PM
|
#8 |
|
Account Suspended
Join Date: Dec 2005
Location: martin georgia
Posts: 568
|
Re: 73' on a 69'?
im just gonna use the frnt end, ill put 6 lug rotors so i can keep my western turbines. itll be easier, less modifying
|
|
|
|
|
02-06-2006, 12:22 AM
|
#9 | |
|
Registered User
Join Date: Apr 2001
Location: DALLAS,TX
Posts: 21,963
|
Re: 73' on a 69'?
Quote:
__________________
67SWB-B.B.RetroRod 64SWB-Recycle 89CCDually-Driver/Tow Truck 99CCSWB Driver All Fleetsides @rattlecankustoms in IG Building a small, high rpm engine with the perfect bore, stroke and rod ratio is very impressive. It's like a highly skilled Morrocan sword fighter with a Damascus Steel Scimitar..... Cubic inches is like Indiana Jones with a cheap pistol. |
|
|
|
|
|
02-07-2006, 01:28 PM
|
#10 |
|
Account Suspended
Join Date: Dec 2005
Location: martin georgia
Posts: 568
|
Re: 73' on a 69'?
and by getting the 73 front end, ill have power steering. less strain,more gain.
|
|
|
|
|
02-08-2006, 02:28 AM
|
#11 | |
|
Senior Member
Join Date: Sep 2004
Location: CANADA
Posts: 1,681
|
Re: 73' on a 69'?
Quote:
|
|
|
|
|
 |
| Bookmarks |
| Thread Tools | |
| Display Modes | |
|
|
Linear Mode
