![]() |
Register or Log In To remove these advertisements. |
|
|
![]() |
|
Thread Tools | Display Modes |
![]() |
#1 |
Registered User
Join Date: Feb 2000
Location: Edmonton, Alberta, Canada
Posts: 599
|
Bolting up torque converter
I'm in the middle of putting a "new" th-350 in my step fathers 79 gmc farm truck, old tranny was shot, just bolting verter to flex plate and notice that with the converter pushed all the way back on the splines there is a 1/2" gap between it and the flex plate. do I just pull it forwards? also, the haynes manual says to align verter to flex plate the way they were when you took them off, how do I align it if the converter is also "new"? does it matter? Tranny is out of an 83. Looks identical though. First auto tranny swap! Thanks for the help! Besides that I should get motor/tranny slid back in tomorrow.
Jesse
__________________
Edmonton, Alberta, 67 c-10, Long fleet, front disks, 5 lug rear end, 327 with Vortechs, edlbrock manifold, comp cams XE 256, 600cfm carb. Backed by a getrag 5 speed and 1 piece driveshaft. 1993 Dihatsu Hijet Jumbo cab 4x4, currently converting to battery electric power. |
![]() |
![]() |
![]() |
#2 |
Account Suspended
Join Date: Mar 2001
Location: Virginia Beach, Va. U.S.A.
Posts: 15,320
|
Yes, just pull it forward. 1/2 inch between is normal when pushed all the way back.
![]() |
![]() |
![]() |
![]() |
#3 |
Registered User
Join Date: Nov 2001
Location: Concord, NC
Posts: 2,489
|
Yes just pull it foward to the flexplate and bolt it up. Did you put in a new seal while the tranny was out? Good time to do it.
If there is any vibration, just unbolt the converter and move it over to the next bolt hole, just sort of "clock" it til it runs smoothest then mark the converter and plate. |
![]() |
![]() |
![]() |
#4 |
Registered User
Join Date: Feb 2001
Location: Ohio
Posts: 1,025
|
I agree with Randy on this, You should be fine to just pull it forward, thats what i did when i put in my TH350, and it works fine now.
|
![]() |
![]() |
![]() |
#5 |
Registered User
Join Date: Feb 2000
Location: Edmonton, Alberta, Canada
Posts: 599
|
beauty eh! Just wanted to make sure, thanks for the help! Now I get to slide the whole thing back in by myself using a tractor with a front end loader, hope I don't break anything! it came out fine, I just lifted and shook it enough and the truck fell off! lol just kidding!
Thanks for the tips, Jesse
__________________
Edmonton, Alberta, 67 c-10, Long fleet, front disks, 5 lug rear end, 327 with Vortechs, edlbrock manifold, comp cams XE 256, 600cfm carb. Backed by a getrag 5 speed and 1 piece driveshaft. 1993 Dihatsu Hijet Jumbo cab 4x4, currently converting to battery electric power. |
![]() |
![]() |
![]() |
#6 |
its all about the +6 inches
Join Date: Jan 2001
Location: Hilliard Ohio
Posts: 2,693
|
Your just kidding about shaking it till the truck dropped? It's kinda fun when you actually do that. Thank god this was in a junk yard when I did it.
|
![]() |
![]() |
![]() |
#7 |
Registered User
Join Date: Jan 2001
Location: Killingworth, CT. USA
Posts: 3,378
|
![]()
If the converter was drained, it would be good thing to add a qt of atf into it before install, and a new front pump seal is also a very good thing.
__________________
1971 C10 swb stepside 350/700R4/3.73posi (retired as of 4/22/03) 1998 S10 short bed 2002 S10 Blazer 1942 Oldsmobile 1958 Massey Harris Pony 1951 Wife Killingworth, Connecticut May those who love us, love us, any of those who do not love us, may God turn their hearts. And if God is unable to turn their hearts, may he turn their ankles so we may know them by their limping. A man who works with his hands is a laborer; a man who works with his hands and his brain is a craftsman; but a man who works with his hands and his brain and his heart is an artist. |
![]() |
![]() |
![]() |
#8 | |
its all about the +6 inches
Join Date: Jan 2001
Location: Hilliard Ohio
Posts: 2,693
|
Quote:
I used to say that I worshipped the ground that she leaked oil on...now I can say it without blowing smoke up your tailpipe. |
|
![]() |
![]() |
![]() |
Bookmarks |
Thread Tools | |
Display Modes | |
|
|