brake part - need help - The 1947 - Present Chevrolet & GMC Truck Message Board Network

bobs409 · 03-07-2006, 04:15 PM

I have no idea what it's called but the truck I'm putting back together is missing the part that the emergency brake cables attach to inside the rear brake drums. I have a '71 3/4 ton 2 WD with an Eaton rear.

Does anyone have a pic of these or better yet, have a pair they'd like to sell? I've been to NAPA and they told me they don't sell them. Haven't tried anywhere else yet.

Thanks,

Bob

**dennislbrooks** · 03-07-2006, 04:29 PM

Ok--are you talking about the leveraging arm that the cable end hooks on insdie the drum? There will be many pairs around.

bobs409 · 03-07-2006, 06:50 PM

That sounds like it. The cable goes into it and I think it has a pin on the other end that goes into one of the brake shoes.

Anyone have any? Or where to buy new? I need both sides so I can get this all back together.

Thanks.

**dennislbrooks** · 03-07-2006, 10:37 PM

If no one responds in a timely manner--- keep it towards the top -- ttt and later PM me. I have a pair --- but i would like to get rid of complete rear drums, rotors, brake guts and backing plates--all near new--all Texas. I would replace the rear wheel cylinders tho. All rest very good stuff.

Americanrider · 03-08-2006, 05:17 AM

I have a '72 3/4 eaton rear I'm junking. Let me look tomorrow and see if they are still on it. I'll send them for the cost of postage only.

bobs409 · 03-08-2006, 06:50 AM

Thanks guys!

That is the part I need. (for both sides)

Dennis, wish I knew you had all this a short time ago. I've been searching for good used but couldn't find anything. I just bought ALL brand new!

At last count, I have about $375 dollars into just the rear brake system.

Americanrider, sounds great! I'll gladly pay shipping and something for the parts too. (keeping my fingers crossed)

Bob

Americanrider · 03-09-2006, 04:51 AM

I have both of them still attached, PM your address and I'll get them in the mail.
Rather than pay me just do a favor to the next guy on here who needs a little something. What goes around comes around.

bobs409 · 03-09-2006, 07:21 AM

Great!

Will be so nice to get my truck off the blocks!

I'll send a PM your way.

The favor will be repayed to someone in your honor.

Need anything?

Thanks again,

Bob

Americanrider · 03-11-2006, 05:09 AM

I marked them w/ P (pass side) and D (driver side) wrapped & dropped them into the mail today. Tommy Knotts, member "55454" started this by sending me some free knobs I needed... More good Karma coming your way Tommy

the only thing I need is a good brake bleed and a rust free cab, thanks for the offer.

bobs409 · 03-11-2006, 06:34 AM

Thank you, will let you know when they arrive.

Bob

Longhorn Man · 03-11-2006, 06:43 AM

Bob.. it's amazing how expensive the parts are for the rear ends huh? I got over 5 bills wrapped up in my brakes, and that includes 4 old drums, one old brake cylinder, and old front shoes.

be happy you have an HO52 and not a HO72.

55454 · 03-11-2006, 07:23 AM

Boone, it takes one to know one. You are a good man.

Tommy

03-07-2006, 04:15 PM	#1
bobs409 1969 Custom 30 wrecker Join Date: Sep 2001 Location: Pottsville, Pa Posts: 2,611	brake part - need help I have no idea what it's called but the truck I'm putting back together is missing the part that the emergency brake cables attach to inside the rear brake drums. I have a '71 3/4 ton 2 WD with an Eaton rear. Does anyone have a pic of these or better yet, have a pair they'd like to sell? I've been to NAPA and they told me they don't sell them. Haven't tried anywhere else yet. Thanks, Bob __________________ Bob 63 Impala 283/PG/3.36 (under restoration) 66 Impala 327/PG/3.36 66 Chevelle SS 409/M22/3.55 69 Chevelle 307/PG/3.08 (future restoration) 69 C10 short stepside 454/TH350/3.73 69 Custom 30 tow truck 350/4 spd/4.10 (resto done, CRUISIN TIME!) 71 Cheyenne 20 fleetside 350/4 spd/4.10 71 Chevelle 6/PG/3.08 72 Chevelle 454/M21/4.10

03-07-2006, 04:29 PM	#2
dennislbrooks Registered User Join Date: Feb 2004 Location: Williamsburg, Ohio Posts: 1,807	Re: brake part - need help Ok--are you talking about the leveraging arm that the cable end hooks on insdie the drum? There will be many pairs around.

03-07-2006, 06:50 PM	#3
bobs409 1969 Custom 30 wrecker Join Date: Sep 2001 Location: Pottsville, Pa Posts: 2,611	Re: brake part - need help That sounds like it. The cable goes into it and I think it has a pin on the other end that goes into one of the brake shoes. Anyone have any? Or where to buy new? I need both sides so I can get this all back together. Thanks. __________________ Bob 63 Impala 283/PG/3.36 (under restoration) 66 Impala 327/PG/3.36 66 Chevelle SS 409/M22/3.55 69 Chevelle 307/PG/3.08 (future restoration) 69 C10 short stepside 454/TH350/3.73 69 Custom 30 tow truck 350/4 spd/4.10 (resto done, CRUISIN TIME!) 71 Cheyenne 20 fleetside 350/4 spd/4.10 71 Chevelle 6/PG/3.08 72 Chevelle 454/M21/4.10 Last edited by bobs409; 03-07-2006 at 06:57 PM.

03-07-2006, 10:37 PM	#4
dennislbrooks Registered User Join Date: Feb 2004 Location: Williamsburg, Ohio Posts: 1,807	Re: brake part - need help If no one responds in a timely manner--- keep it towards the top -- ttt and later PM me. I have a pair --- but i would like to get rid of complete rear drums, rotors, brake guts and backing plates--all near new--all Texas. I would replace the rear wheel cylinders tho. All rest very good stuff. Attached Images

03-08-2006, 05:17 AM	#5
Americanrider Registered User Join Date: Dec 2004 Location: NW, WA. Posts: 1,421	Re: brake part - need help I have a '72 3/4 eaton rear I'm junking. Let me look tomorrow and see if they are still on it. I'll send them for the cost of postage only.

03-08-2006, 06:50 AM	#6
bobs409 1969 Custom 30 wrecker Join Date: Sep 2001 Location: Pottsville, Pa Posts: 2,611	Re: brake part - need help Thanks guys! That is the part I need. (for both sides) Dennis, wish I knew you had all this a short time ago. I've been searching for good used but couldn't find anything. I just bought ALL brand new! At last count, I have about $375 dollars into just the rear brake system. Americanrider, sounds great! I'll gladly pay shipping and something for the parts too. (keeping my fingers crossed) Bob __________________ Bob 63 Impala 283/PG/3.36 (under restoration) 66 Impala 327/PG/3.36 66 Chevelle SS 409/M22/3.55 69 Chevelle 307/PG/3.08 (future restoration) 69 C10 short stepside 454/TH350/3.73 69 Custom 30 tow truck 350/4 spd/4.10 (resto done, CRUISIN TIME!) 71 Cheyenne 20 fleetside 350/4 spd/4.10 71 Chevelle 6/PG/3.08 72 Chevelle 454/M21/4.10

03-09-2006, 04:51 AM	#7
Americanrider Registered User Join Date: Dec 2004 Location: NW, WA. Posts: 1,421	Re: brake part - need help I have both of them still attached, PM your address and I'll get them in the mail. Rather than pay me just do a favor to the next guy on here who needs a little something. What goes around comes around.

03-09-2006, 07:21 AM	#8
bobs409 1969 Custom 30 wrecker Join Date: Sep 2001 Location: Pottsville, Pa Posts: 2,611	Re: brake part - need help Great! Will be so nice to get my truck off the blocks! I'll send a PM your way. The favor will be repayed to someone in your honor. Need anything? Thanks again, Bob __________________ Bob 63 Impala 283/PG/3.36 (under restoration) 66 Impala 327/PG/3.36 66 Chevelle SS 409/M22/3.55 69 Chevelle 307/PG/3.08 (future restoration) 69 C10 short stepside 454/TH350/3.73 69 Custom 30 tow truck 350/4 spd/4.10 (resto done, CRUISIN TIME!) 71 Cheyenne 20 fleetside 350/4 spd/4.10 71 Chevelle 6/PG/3.08 72 Chevelle 454/M21/4.10

03-11-2006, 05:09 AM	#9
Americanrider Registered User Join Date: Dec 2004 Location: NW, WA. Posts: 1,421	Re: brake part - need help I marked them w/ P (pass side) and D (driver side) wrapped & dropped them into the mail today. Tommy Knotts, member "55454" started this by sending me some free knobs I needed... More good Karma coming your way Tommy the only thing I need is a good brake bleed and a rust free cab, thanks for the offer.

03-11-2006, 06:34 AM	#10
bobs409 1969 Custom 30 wrecker Join Date: Sep 2001 Location: Pottsville, Pa Posts: 2,611	Re: brake part - need help Thank you, will let you know when they arrive. Bob __________________ Bob 63 Impala 283/PG/3.36 (under restoration) 66 Impala 327/PG/3.36 66 Chevelle SS 409/M22/3.55 69 Chevelle 307/PG/3.08 (future restoration) 69 C10 short stepside 454/TH350/3.73 69 Custom 30 tow truck 350/4 spd/4.10 (resto done, CRUISIN TIME!) 71 Cheyenne 20 fleetside 350/4 spd/4.10 71 Chevelle 6/PG/3.08 72 Chevelle 454/M21/4.10

03-11-2006, 06:43 AM	#11
Longhorn Man its all about the +6 inches Join Date: Jan 2001 Location: Hilliard Ohio Posts: 2,690	Re: brake part - need help Bob.. it's amazing how expensive the parts are for the rear ends huh? I got over 5 bills wrapped up in my brakes, and that includes 4 old drums, one old brake cylinder, and old front shoes. be happy you have an HO52 and not a HO72.

03-11-2006, 07:23 AM	#12
55454 55454 Join Date: Mar 2005 Location: Lafayette La. Posts: 340	Re: brake part - need help Boone, it takes one to know one. You are a good man. Tommy __________________ 72 Cheyenne 1956 3100 1955 210 19 year old Chihuahua (Factory Teeth)

Thread Tools
Show Printable Version Email this Page
Display Modes
Linear Mode Switch to Hybrid Mode Switch to Threaded Mode



Register or Log In To remove these advertisements.

Register or Log In To remove these advertisements.