'92 Chevy seat - The 1947 - Present Chevrolet & GMC Truck Message Board Network

**53burb** · 03-20-2006, 02:03 AM

I have a '92 Chevy 60/40 seat to install in my Burb. What are you guys using as a spacer for the inside passenger side bracket?? If nothing else, I can get a couple pieces of 1/2" SS tubing to use as spacers and I have a few seat and/or seatbelt washers for underneath the floorboard.

**53burb** · 03-20-2006, 12:52 PM

ttt

**Palf70Step** · 03-20-2006, 01:43 PM

I used a plumbing fixture a 3/4" to 1/2" pipe fitting, then as necessary used a few washer to get the exact adjustment.

**53burb** · 03-20-2006, 06:07 PM

Thanks,
Did you use the the rear mounting seat holes in your truck, I figured I was going to use those, or did you drill 8 new holes???

**Palf70Step** · 03-20-2006, 10:52 PM

You can check my website in my signature, interrior section on what I did, but no I used the front holes as a guide for the outer front, then I drilled the rear holes and inner holes. I don't remember, but if you mount the drivers side flat on the floor, I don't thing it will slide back enough to use the rear holes. I could be wrong, but I believe that is why I initially chose the fron holes. Plus I like the seating position better that way.

**53burb** · 03-21-2006, 12:39 AM

Thanks for the info. Your webpage is pretty good. How is Gulfport?? Did you make it thru Katrina?? I spent about six months in Biloxi at Keesler AFB in the early nineties when I was still in the service. Great time. Oh yeah, I am sure you know Brett Favre is from there.

rauto13 · 03-21-2006, 01:42 AM

I used two pieces of angle steel bolted together. I also used six flat washers under the rear of the outer seat bracket. I used the outer front holes as a starting point and drilled the reso of the holes and put fender washers under the floor for support.

**53burb** · 03-21-2006, 02:11 AM

What was the angled steel used for???

**Palf70Step** · 03-21-2006, 06:27 AM

Quote:

Originally Posted by 53burb

Thanks for the info. Your webpage is pretty good. How is Gulfport?? Did you make it thru Katrina?? I spent about six months in Biloxi at Keesler AFB in the early nineties when I was still in the service. Great time. Oh yeah, I am sure you know Brett Favre is from there.

Lot of things are different since the old hag landed last Aug. I have been out at Keesler (this time) since the mid 80s. Around the base and parts of Biloxi you would not know this place was ravage by a major hurricane. Folks have built back fast. Certain areas, and the further west you get it gest much worse. You hit the next town past me and it goes down hill fast.

Not too much left of Brett's home town, course there wasn't a lot there to begin with.

03-20-2006, 02:03 AM	#1
53burb Senior Member Join Date: May 2004 Location: Queen Creek, AZ Posts: 1,010	'92 Chevy seat I have a '92 Chevy 60/40 seat to install in my Burb. What are you guys using as a spacer for the inside passenger side bracket?? If nothing else, I can get a couple pieces of 1/2" SS tubing to use as spacers and I have a few seat and/or seatbelt washers for underneath the floorboard.

03-20-2006, 12:52 PM	#2
53burb Senior Member Join Date: May 2004 Location: Queen Creek, AZ Posts: 1,010	Re: '92 Chevy seat ttt

03-20-2006, 01:43 PM	#3
Palf70Step State of Confusion! Join Date: Jul 2002 Location: Gulfport, MS USA Posts: 47,216	Re: '92 Chevy seat I used a plumbing fixture a 3/4" to 1/2" pipe fitting, then as necessary used a few washer to get the exact adjustment. __________________ Bill 1970 Chevy Custom/10 LWB Fleetside 2010 Toyota Tacoma PreRunner SR5 Double Cab - DD Member of Louisiana Classic Truck Club (LCTC) Bill's Gallery Life isn't tied with a bow, but it's still a gift. Live simply. Love generously. Care deeply. Speak kindly. Leave the rest to God! Last edited by Palf70Step; 03-20-2006 at 01:44 PM.

03-20-2006, 06:07 PM	#4
53burb Senior Member Join Date: May 2004 Location: Queen Creek, AZ Posts: 1,010	Re: '92 Chevy seat Thanks, Did you use the the rear mounting seat holes in your truck, I figured I was going to use those, or did you drill 8 new holes???

03-20-2006, 10:52 PM	#5
Palf70Step State of Confusion! Join Date: Jul 2002 Location: Gulfport, MS USA Posts: 47,216	Re: '92 Chevy seat You can check my website in my signature, interrior section on what I did, but no I used the front holes as a guide for the outer front, then I drilled the rear holes and inner holes. I don't remember, but if you mount the drivers side flat on the floor, I don't thing it will slide back enough to use the rear holes. I could be wrong, but I believe that is why I initially chose the fron holes. Plus I like the seating position better that way. __________________ Bill 1970 Chevy Custom/10 LWB Fleetside 2010 Toyota Tacoma PreRunner SR5 Double Cab - DD Member of Louisiana Classic Truck Club (LCTC) Bill's Gallery Life isn't tied with a bow, but it's still a gift. Live simply. Love generously. Care deeply. Speak kindly. Leave the rest to God!

03-21-2006, 12:39 AM	#6
53burb Senior Member Join Date: May 2004 Location: Queen Creek, AZ Posts: 1,010	Re: '92 Chevy seat Thanks for the info. Your webpage is pretty good. How is Gulfport?? Did you make it thru Katrina?? I spent about six months in Biloxi at Keesler AFB in the early nineties when I was still in the service. Great time. Oh yeah, I am sure you know Brett Favre is from there. Last edited by 53burb; 03-21-2006 at 12:40 AM.

03-21-2006, 01:42 AM	#7
rauto13 saving one more Join Date: Sep 2005 Location: Pryor Creek, Oklahoma Posts: 3,066	Re: '92 Chevy seat I used two pieces of angle steel bolted together. I also used six flat washers under the rear of the outer seat bracket. I used the outer front holes as a starting point and drilled the reso of the holes and put fender washers under the floor for support. __________________ 72 Chevy longbed - now for parts 69 Chevy short fleet - needing some love 70 RS Camaro - needing more love driver - 96 GMC X-cab

03-21-2006, 02:11 AM	#8
53burb Senior Member Join Date: May 2004 Location: Queen Creek, AZ Posts: 1,010	Re: '92 Chevy seat What was the angled steel used for???

Thread Tools
Show Printable Version Email this Page
Display Modes
Linear Mode Switch to Hybrid Mode Switch to Threaded Mode



Register or Log In To remove these advertisements.

Register or Log In To remove these advertisements.