Parting out 87 Chevy (K-20) 3/4 ton Pickup - The 1947 - Present Chevrolet & GMC Truck Message Board Network

dpmalibu · 04-01-2006, 11:12 AM

Only body parts are the hood and front fenders. The driver side has rot on inside of fender.Not sure about the pass. fender yet. Hood is straight. Dana 44 front rear and 14 bolt FF in rear(SOLD). Both have 4.10's. Trans is t-400 and has been rebuilt. Has 25,000 miles and new converter. Motor has been sold. NP208 Transfer case. Also have both shafts. No bed.Prices are the following:

2) T-400 trans $400

3) Np208 $125

4) hood $40

8) driveshafts $20 front/ rear $40

Don't have any other parts except for what I listed; This was a running and driving truck before the guy I bought it from started taking it apart. if interested in anything give me a call (609) 481-8811

alf4444 · 04-02-2006, 10:57 PM

how much for the 8 lug outers on the d44 (everything to convert to 8 lug) shipped to 84118

dpmalibu · 04-03-2006, 05:55 PM

Sorry I sold the rears yesterday.

karichey22 · 04-05-2006, 12:06 AM

would the front driveshaft fit a 1/2?

dpmalibu · 04-06-2006, 01:40 PM

I don't see why not. The rears in both a 1/2 ton and 3/4 ton are dana 44 and the transfer cases are both NP208's.Let me know what you want to do.

04-01-2006, 11:12 AM	#1
dpmalibu Registered User Join Date: Dec 2004 Location: Hatboro,PA Posts: 367	Parting out 87 Chevy (K-20) 3/4 ton Pickup Only body parts are the hood and front fenders. The driver side has rot on inside of fender.Not sure about the pass. fender yet. Hood is straight. Dana 44 front rear and 14 bolt FF in rear(SOLD). Both have 4.10's. Trans is t-400 and has been rebuilt. Has 25,000 miles and new converter. Motor has been sold. NP208 Transfer case. Also have both shafts. No bed.Prices are the following: 2) T-400 trans $400 3) Np208 $125 4) hood $40 8) driveshafts $20 front/ rear $40 Don't have any other parts except for what I listed; This was a running and driving truck before the guy I bought it from started taking it apart. if interested in anything give me a call (609) 481-8811 Last edited by dpmalibu; 04-03-2006 at 09:13 PM.

04-02-2006, 10:57 PM	#2
alf4444 Registered User Join Date: Dec 2002 Location: taylorsville, UT Posts: 778	Re: Parting out 87 Chevy (K-20) 3/4 ton Pickup how much for the 8 lug outers on the d44 (everything to convert to 8 lug) shipped to 84118 __________________ 2011 CCSB GMC 2500HD DMAX 73 GMC 3/4 ton 4x4 96 Chevy 1500 STD Cab Shortbed Z71 Owner of WickedWolfRC.com

04-03-2006, 05:55 PM	#3
dpmalibu Registered User Join Date: Dec 2004 Location: Hatboro,PA Posts: 367	Re: Parting out 87 Chevy (K-20) 3/4 ton Pickup Sorry I sold the rears yesterday.

04-05-2006, 12:06 AM	#4
karichey22 Registered User Join Date: Jul 2005 Location: Red Oak, TX Posts: 11	Re: Parting out 87 Chevy (K-20) 3/4 ton Pickup would the front driveshaft fit a 1/2? __________________ 83 swb in the works.

04-06-2006, 01:40 PM	#5
dpmalibu Registered User Join Date: Dec 2004 Location: Hatboro,PA Posts: 367	Re: Parting out 87 Chevy (K-20) 3/4 ton Pickup I don't see why not. The rears in both a 1/2 ton and 3/4 ton are dana 44 and the transfer cases are both NP208's.Let me know what you want to do.

Thread Tools
Show Printable Version Email this Page
Display Modes
Linear Mode Switch to Hybrid Mode Switch to Threaded Mode



Register or Log In To remove these advertisements.

Register or Log In To remove these advertisements.