Trouble pulling my 350 - The 1947 - Present Chevrolet & GMC Truck Message Board Network

**Daubs** · 04-23-2006, 03:36 PM

It's a 72 K-20 with 350 and 4 speed manual tranny. I've pulled everything from the engine and disconnected engine mounts. Have the engine hoist bolted in and positioned. Can raise the engine, but can't pull her away from the 4 speed manual.

I've removed the two bolts that connect manual tranny to bell housing. Can't seem to find any more bolts. Am I doing something wrong? Can't even pry her apart.

Suggestions? Thanks.

Longhorn Man · 04-23-2006, 03:38 PM

Get in the truck and hit the clutch pedal, sometimes that helps. Your trans input shaft probably has a burr on it or something

red71cheyenne · 04-23-2006, 03:58 PM

There are 4 bolts from bellhousing to tranny as well. Two outside on top, and two inside on bottom coming from inside the bellhousing.

**Daubs** · 04-23-2006, 04:31 PM

Quote:

Originally Posted by red71cheyenne

There are 4 bolts from bellhousing to tranny as well. Two outside on top, and two inside on bottom coming from inside the bellhousing.

THANKS! That was my problem!!! It's out and swinging right now. Have housing off as well as clutch & flywheel. Need to make run to hardware store for bolts long enough for engine stand

Happy.

red71cheyenne · 04-23-2006, 04:43 PM

Congrats! Post some pics!

04-23-2006, 03:36 PM	#1
Daubs Registered User Join Date: Jan 2005 Location: Eastern Nebraska Posts: 613	Trouble pulling my 350 It's a 72 K-20 with 350 and 4 speed manual tranny. I've pulled everything from the engine and disconnected engine mounts. Have the engine hoist bolted in and positioned. Can raise the engine, but can't pull her away from the 4 speed manual. I've removed the two bolts that connect manual tranny to bell housing. Can't seem to find any more bolts. Am I doing something wrong? Can't even pry her apart. Suggestions? Thanks. __________________ '72 Chevy K-20 Crate 350, SM465, 4.10's

04-23-2006, 03:38 PM	#2
Longhorn Man its all about the +6 inches Join Date: Jan 2001 Location: Hilliard Ohio Posts: 2,690	Re: Trouble pulling my 350 Get in the truck and hit the clutch pedal, sometimes that helps. Your trans input shaft probably has a burr on it or something

04-23-2006, 03:58 PM	#3
red71cheyenne Back in the sticks Join Date: Jan 2001 Location: Fordland, MO Posts: 3,188	Re: Trouble pulling my 350 There are 4 bolts from bellhousing to tranny as well. Two outside on top, and two inside on bottom coming from inside the bellhousing. __________________ 1971 Cheyenne C-10 w/700R4 and Tuned Port Injection 1969 K5 Blazer w/Tuned Port 2010 2SS/RS Flaming Orange Camaro 2011 K1500 Suburban 2014 K1500 Pickup 2008 Nissan Altima? The wifes' hoopty

04-23-2006, 04:43 PM	#5
red71cheyenne Back in the sticks Join Date: Jan 2001 Location: Fordland, MO Posts: 3,188	Re: Trouble pulling my 350 Congrats! Post some pics! __________________ 1971 Cheyenne C-10 w/700R4 and Tuned Port Injection 1969 K5 Blazer w/Tuned Port 2010 2SS/RS Flaming Orange Camaro 2011 K1500 Suburban 2014 K1500 Pickup 2008 Nissan Altima? The wifes' hoopty

Thread Tools
Show Printable Version Email this Page
Display Modes
Linear Mode Switch to Hybrid Mode Switch to Threaded Mode



Register or Log In To remove these advertisements.

Register or Log In To remove these advertisements.