I'm new here, and I need some help! You see... - The 1947 - Present Chevrolet & GMC Truck Message Board Network

BIG CTY · 11-01-2006, 12:08 AM

...everytime I do something to my rustbucket I seem to mess something else up. But before I get into that, here is the post I put on the "Welcome" forum introducing myself. Now back to the issues

First, I put a new steering wheel on my bucket. I tightened it down too far, but I finally got it right - with one issue...the horn ALWAYS blows. So I disconnected it and straight wired a horn. Now my battery is dying. (My signal lights no longer cancel either, but I guess I have to live with that) Could it be that there is current being drawn from inside that d@mn steering wheel somewhere?

Also, I put in a brand new used bench seat from the junkyard in my bucket. After installing, the gas gauge stopped working. When I turn the key, it goes all the way past the "F." What in the he!! could that be? What should I check?

I'm sure there is more, but I'll stick to that for right now....

Help HELP!! Thanks in advance!

Bishops Trucks · 11-01-2006, 12:24 AM

First of all Welcome to the board.
1. Did you put the canceling cam (round plastic piece with a couple little legs on it) back in and in the right direction?
2. If the wire for the horn is still in the column and touching metal that will definatey cause a drain.
3.When you put the new seat in you could have unplugged the wire to the sending unit on the tank.
Good luck and post your problems, you will get good advice from people on this sight.

GR82BME · 11-01-2006, 11:55 AM

Something else you might want to check is when you bolted down your seat if you dident smash the fuel wire down when tightening up your seat...

FishSteelhead · 11-23-2006, 04:42 PM

Had basically th same problem ie., battery drainin' because of wire touchin' metal after removal of steering wheel. As far as the gas gauge, check wirin' on tank, could have pulled it loose or cut into wires while yankin' seat out...

larry may · 11-23-2006, 09:45 PM

the fuel gage wire should run under the driver side door threshold molding. most are under the mat or carpet. Could have as mentioned earlier in this thread. the wire could be pinched. it is tan in color.......my.02%

11-01-2006, 12:08 AM	#1
BIG CTY Between the earth and the sky Join Date: Oct 2006 Location: Chesapeake, VA Posts: 822	I'm new here, and I need some help! You see... ...everytime I do something to my rustbucket I seem to mess something else up. But before I get into that, here is the post I put on the "Welcome" forum introducing myself. Now back to the issues First, I put a new steering wheel on my bucket. I tightened it down too far, but I finally got it right - with one issue...the horn ALWAYS blows. So I disconnected it and straight wired a horn. Now my battery is dying. (My signal lights no longer cancel either, but I guess I have to live with that) Could it be that there is current being drawn from inside that d@mn steering wheel somewhere? Also, I put in a brand new used bench seat from the junkyard in my bucket. After installing, the gas gauge stopped working. When I turn the key, it goes all the way past the "F." What in the he!! could that be? What should I check? I'm sure there is more, but I'll stick to that for right now.... Help HELP!! Thanks in advance! __________________ Chris - 1966 C10 Shortbed Fleetside, 1991 GMC Sierra 1500 Extended Cab, 1993 Blazer Sport 4x4 My other rides: 1969 Chevrolet Impala SS427 Convertible 1976 Dodge Tradesman B200 2002 Nissan Maxima 6 speed 2004 Mercedes Benz CL500

11-01-2006, 12:24 AM	#2
Bishops Trucks KEEP ON TRUCKIN' Join Date: Jun 2005 Location: Sterling, Va. Posts: 5,730	Re: I'm new here, and I need some help! You see... First of all Welcome to the board. 1. Did you put the canceling cam (round plastic piece with a couple little legs on it) back in and in the right direction? 2. If the wire for the horn is still in the column and touching metal that will definatey cause a drain. 3.When you put the new seat in you could have unplugged the wire to the sending unit on the tank. Good luck and post your problems, you will get good advice from people on this sight. __________________ JIM '97 GMC Sierra K1500 '95 Chevy Silverado C1500 '71 Cheyenne Z71 / LT1 & 4-Speed SWB K/10 Father/Son Project http://www.youtube.com/watch?v=4l689JKXPnA http://67-72chevytrucks.com/vboard/payments.php "LIVIN' FREE FOREVER"

11-01-2006, 11:55 AM	#3
GR82BME Registered User Join Date: Oct 2006 Location: Billings MT Posts: 38	Re: I'm new here, and I need some help! You see... Something else you might want to check is when you bolted down your seat if you dident smash the fuel wire down when tightening up your seat...

11-23-2006, 04:42 PM	#4
FishSteelhead Registered User Join Date: Nov 2006 Location: Central Valley of California Posts: 5	Re: I'm new here, and I need some help! You see... Had basically th same problem ie., battery drainin' because of wire touchin' metal after removal of steering wheel. As far as the gas gauge, check wirin' on tank, could have pulled it loose or cut into wires while yankin' seat out... __________________ "There's no head like Steelhead"...

11-23-2006, 09:45 PM	#5
larry may Senior Member Join Date: Jul 2005 Location: MISSOURI Posts: 3,256	Re: I'm new here, and I need some help! You see... the fuel gage wire should run under the driver side door threshold molding. most are under the mat or carpet. Could have as mentioned earlier in this thread. the wire could be pinched. it is tan in color.......my.02% __________________ The biggest problem people have, is other people Thou shalt be cool and not hassle Be a site supporter. The heart of the wise inclines to the right, but the heart of the fool inclines to the left." Ecclesiastes 10:2

Thread Tools
Show Printable Version Email this Page
Display Modes
Linear Mode Switch to Hybrid Mode Switch to Threaded Mode



Register or Log In To remove these advertisements.

Register or Log In To remove these advertisements.