Parting out 3/4 71 chevy 2wd AZ

[t korinek]

Good doors no rust, complete with chrome wing windows, no speaker holes $125 each. Good bed sides, $100 each, passenger side toolbox door $100. Bed floor is straight but has been cut & will be selling patches of it. HO52 rear end coil spring 4.57 non locker$ 150. Auto crossmember $35. Auto linkage complete setup $30. small block engine towers $25. Driveshaft $30. rear slider $25. All prices + shipping. I have other parts not listed off this truck, just ask. Tom 480-241-1318

[t korinek]

Some more pics

[Down south truckin]

I'm interested in the tool box door pending pictures and a shipping quote to 30047 thanks Mike

[t korinek]

I'll get some pics & shipping on monday eve. Tom

[t korinek]

For Down south truckin: Pics of the bed door, I don't have the key for the lock, no rust, a few little dents. $115 shipped & insured. Tom

[D-Bo]

Would the bumper polish up clean? How about the tail lights, reverse light, sidemarkers. They look like they were recently replaced. Are they in good condition? Could you send me some pics of these to damien@cmfmail.com

[uncle]

I'll take it if downsouthtrukin passes.

[Down south truckin]

T korinek looks good pm me your info and i'll send you a money order asap

[D M. Manning]

How much for upper and lower A Arms.

[t korinek]

Pics for D Bo, the lenses are all driver quality only, they are a little faded & the rear covers have some chips out of the edges. $22 shipped for all 8 pieces if you want them, Bumper not chrome. Uncle, Toolbox door sale pending. D.M Manning complete front end is sale pending, I'll let you know if it falls through. More pics of the doors for a few of you that were asking. Tom

[t korinek]

More pics

[t korinek]

more door pics

[Cochise]

I know it's been a while since this was posted but do you have a good, rust free door, and if so, how much would you want for it shipped to Arkansas by Greyhound? I don't care about glass and panels and such, unless they are a pain to remove.

[gvot57]

does it have a leaf spring rear if so how much for the spring plates
thanks shawn

[Blizz]

the fenders look like they're in good shape, do you still have them and if so, what are you asking for them? can you take some better pics of them?

[D.PASSMORE]

Intrested in the doors...

[lutherb69]

Would like to get driver bedside if you could PM a price with shipping to 01731 Thanks

[t korinek]

Cochise, I have a few good doors,I'll have to get some pics & shipping prices
Gvot57, rear end is gone
Blizz, fenders are gone
Dpassmore, doors will be here for you to look at when you pick up the cab.
lutherb69, i'll get a quote on the bedside shipping, I would expect at least $100

[sneezys72]

Do you have a driver quality passenger side deluxe mirror?

[BACKYARD88]

I'd be interested in the section of frame that the steering gear bolts to if it isn't cracked and you could cut it off.

[mwerfner]

how is the steel around the vents I need the vent cut outs if you will cut and ship I would be greatful. Let me know Marc mwerfner@yahoo.com

[rodstored-72]

tk,
by chance would you have any really good driver quality tailgates?? preferably w/o any bowing & very minimal, if any, rust??

thanks!!!
rodstored-72

[gtomechanic]

Do you have four of the trim rings,are they on 16.5 rims? If so how much shipped to 19320?

[t korinek]

Sneezy, I'll check on the mirror
Backyard88, don't have that piece of frame right now, I'm sure I'll get one if your not in a big hurry
Mwerfner, working on the vent cutouts
Rodstored 72, I have a real nice factory tailgate $250
GTOmechanic, the trim rings are 16" they are from a later model 3/4 ton
Thanks,
Tom

[GMC Jim]

I could use the front bed panel....need price and shipping to Portland, OR zip 97233