|
Register or Log In To remove these advertisements. |
|
|
|
|||||||
 |
|
|
Thread Tools | Display Modes |
02-08-2007, 10:59 PM
|
#1 |
|
Sierra Grande Club
Join Date: Jan 2007
Location: New Mexico USA
Posts: 2,433
|
Oil pan gasket thick or thin??
I’m looking for a one piece gasket on summit, they list’em as thick or thin front seal. Do you know what I need? How do I tell?
s/t
__________________
1971 GMC Sierra Grande, 1/2 ton short wide, original 4 bolt 010 020 block & heads. (matching #'s). 383 stroker, SMI q jet 750 cfm, Lunati Voodoo 60102 cam, Scorpion roller rockers, Spin Tech pro street mufflers with X pipe. 
|
|
|
|
02-08-2007, 11:58 PM
|
#2 |
|
Senior Member
Join Date: Oct 2006
Location: Edmonton Alberta
Posts: 458
|
Re: Oil pan gasket thick or thin??
thats news to me, never seen that before. Could be listed that way instead of 1 or 2 piece rear seal?
|
|
|
|
|
02-09-2007, 12:07 AM
|
#3 |
|
Registered User
Join Date: Apr 2006
Location: MinneSNOWta
Posts: 1,381
|
Re: Oil pan gasket thick or thin??
Not sure personally,
it might help others viewing this thread if you post what you have for an engine. most important, Gen I or Gen II (LT based). If you know the MFG year of the motor that could be helpful too. Good luck
__________________
2003 GMC Sierra 1500 WT 1995 Nissan Hardbody 2016 Hyundai Veloster Turbo DC2 (SW/AW) Clyde W. Harvey USN "Socialism is a philosophy of failure, the creed of ignorance, and the gospel of envy, its inherent virtue is the equal sharing of misery" Winston Churchill Last edited by brak; 02-09-2007 at 12:07 AM. |
|
|
|
|
02-09-2007, 01:35 AM
|
#4 |
|
~Rest In Peace~
Join Date: May 2005
Location: CALIFORNIA NOR CAL
Posts: 9,707
|
Re: Oil pan gasket thick or thin??
i like my pizza thick style
__________________
is it fast ? it has a lighting bolt donut? B___H please, I can remove 90% of your so called "beauty" with a kleenex |
|
|
|
|
02-09-2007, 09:10 AM
|
#5 | |
|
Sierra Grande Club
Join Date: Jan 2007
Location: New Mexico USA
Posts: 2,433
|
Re: Oil pan gasket thick or thin??
Quote:
s/t
__________________
1971 GMC Sierra Grande, 1/2 ton short wide, original 4 bolt 010 020 block & heads. (matching #'s). 383 stroker, SMI q jet 750 cfm, Lunati Voodoo 60102 cam, Scorpion roller rockers, Spin Tech pro street mufflers with X pipe.
|
|
|
|
|
|
02-09-2007, 09:44 AM
|
#6 |
|
Senior Member
Join Date: Oct 2006
Location: Edmonton Alberta
Posts: 458
|
Re: Oil pan gasket thick or thin??
I checked summit, the 55-86 is called thick, the 1 piece frear seal is not called thin though, its just called 86-99
|
|
|
|
|
02-09-2007, 09:44 AM
|
#7 | |
|
Registered User
Join Date: Nov 2006
Location: Illinois
Posts: 306
|
Re: Oil pan gasket thick or thin??
Quote:
__________________
'67 C20 Lwb 350 4-Speed '01 Chrysler Concorde LXI (wifes ride) '91 Gmc Suburban 3/4 2wd 454 Tbi '51 Jeep Cj3a "Willys" 350 V8 |
|
|
|
|
|
02-09-2007, 11:05 AM
|
#8 |
|
Registered User
Join Date: Apr 2006
Location: oklahoma
Posts: 10,670
|
Re: Oil pan gasket thick or thin??
The way I under stand it there was a thin front and rear gasket from 55- 74 and 75 to 79 gasket the thick front and rear seals. Look up summits stock replacement oil pans in there catalog and it will tell you. 80 - 86 is a whole other animal, ie drivers side dip stick and 87 up is 1 piece rear main seal that also is a whole other animal oil pan gasket wise. Good luck.
Last edited by Aarons72s; 02-09-2007 at 11:07 AM. |
|
|
|
|
02-09-2007, 01:43 PM
|
#9 |
|
GEARHEAD
Join Date: Jan 2007
Location: CENTRAL,PA
Posts: 2,284
|
Re: Oil pan gasket thick or thin??
It depends on the timing cover you are using. The older style was the thin (I'm not at the shop to mesure exact but) close too 1/4 inch thick is closer toa heavy 3/8's little less than 1/2 if memory serves me right. TTT for some one that cam mesure for sure.
|
|
|
|
|
| Bookmarks |
| Thread Tools | |
| Display Modes | |
|
|
Linear Mode
