Where to buy eaton ho 52 rebuild parts - The 1947 - Present Chevrolet & GMC Truck Message Board Network

**t korinek** · 03-08-2007, 03:10 AM

I have a friend getting ready to rebuild an eaton HO 52 rear out of a 4x4. does anyone have a good place to get the bearings & seals & do they make an aftermarket posi or locker for this? Thanks in advance for any info.
Tom

69k5 · 03-08-2007, 07:20 PM

autozone can get the bearings . they are cheapest from a bearing supplier but you will have to take the bearings in for them to get the number off of them. autozone or advance auto parts are not too bad. you can look up the prices on their online store. the brakes are what kill you. it is way cheaper to swap to disk brakes than to just buy pads for one of these. that is what I did on mine. you can do a search for my name and eaton on here. I know I have posted the numbers and prices on here before, but I have been gone a long time.

you can only get a detroit locker for these. randy's ring and pinion will have them and can get sets of new gears. or just look around on here they pop up from time to time.

**special-K** · 03-08-2007, 09:25 PM

Napa has it all.No bolt-in traction enhancement available new.

03-08-2007, 03:10 AM	#1
t korinek Truckin' Krazy Join Date: May 2000 Location: mesa az Posts: 6,193	Where to buy eaton ho 52 rebuild parts I have a friend getting ready to rebuild an eaton HO 52 rear out of a 4x4. does anyone have a good place to get the bearings & seals & do they make an aftermarket posi or locker for this? Thanks in advance for any info. Tom __________________ Dealer for: American Auto Wire Precision weatherstripping Dakota Digital Trim parts Carpets Truck World seat covers & Many others Chevy Parts locator in Mesa AZ!

03-08-2007, 07:20 PM	#2
69k5 Registered User Join Date: Nov 2003 Location: Monroe, La 71202 Posts: 317	Re: Where to buy eaton ho 52 rebuild parts autozone can get the bearings . they are cheapest from a bearing supplier but you will have to take the bearings in for them to get the number off of them. autozone or advance auto parts are not too bad. you can look up the prices on their online store. the brakes are what kill you. it is way cheaper to swap to disk brakes than to just buy pads for one of these. that is what I did on mine. you can do a search for my name and eaton on here. I know I have posted the numbers and prices on here before, but I have been gone a long time. you can only get a detroit locker for these. randy's ring and pinion will have them and can get sets of new gears. or just look around on here they pop up from time to time.

03-08-2007, 09:25 PM	#3
special-K Special Order Join Date: Nov 2004 Location: Mt Airy, MD Posts: 85,851	Re: Where to buy eaton ho 52 rebuild parts Napa has it all.No bolt-in traction enhancement available new. __________________ "BUILDING A BETTER WAY TO SERVE THE USA"......67/72......"The New Breed" GMC '67 C1500 Wideside Super Custom SWB: 327/M22/3.42 posi.........."The '67" (project) GMC '72 K2500 Wideside Sierra Custom Camper: 350/TH350/4.10 Power-Lok..."The '72" (rolling) Tim "Don't call me a redneck. I'm a rough cut country gentleman" R.I.P. ~ East Side Low Life ~ El Jay ~ 72BLUZ ~ Fasteddie69 ~ Ron586 ~ 67ChevyRedneck ~ Grumpy Old Man ~

Thread Tools
Show Printable Version Email this Page
Display Modes
Linear Mode Switch to Hybrid Mode Switch to Threaded Mode



Register or Log In To remove these advertisements.

Register or Log In To remove these advertisements.