Will this work??? - The 1947 - Present Chevrolet & GMC Truck Message Board Network

jkade · 06-12-2007, 08:59 PM

I may have found a deal on some tubular lower control arms and a 73-87 crossmember that a guy bought with a project truck and he isn't going to use any of it. The crossmember has been cut and set up for a rack and the tubular lower arms are new with balljoints and are for a 87 down. Will my spindles work with this? I would buy some tubular uppers also to match the lowers, so would I buy for 72 or 87 down?

GREASEMONKEY72 · 06-12-2007, 09:04 PM

i dont think the spindles fit the 73+ a-arms but i could be wrong

jkade · 06-12-2007, 09:07 PM

Quote:

Originally Posted by GREASEMONKEY72

i dont think the spindles fit the 73+ a-arms but i could be wrong

Could I keep my arms and use the crossmember??

SCOTI · 06-12-2007, 11:15 PM

Spindles will interchange if the correct year ball joints are used (73-87 spindles need 73-87 BJ's; 71-72 spindles need 71-72 stuff etc...).

Again.... same for the upper tubular arm question. Just get the right BJ for your spindle & it will bolt in to a later style a-arm.

I used 73-up disc brake spindles on my 68 lower a-arms using the later BJ.s. I used the 68 upper a-arms w/the later BJ's. I connected the steering arms to the tie-rods w/a 72 center-link on one truck & on my other one I just went ahead & used all 73-up steering gear cause the 73-up center-link was easier to find @ a wrecking yard.

GREASEMONKEY72 · 06-12-2007, 11:18 PM

well that answers it for both of us^

jkade · 06-12-2007, 11:46 PM

Quote:

Originally Posted by SCOTI

Spindles will interchange if the correct year ball joints are used (73-87 spindles need 73-87 BJ's; 71-72 spindles need 71-72 stuff etc...).

Again.... same for the upper tubular arm question. Just get the right BJ for your spindle & it will bolt in to a later style a-arm.

I used 73-up disc brake spindles on my 68 lower a-arms using the later BJ.s. I used the 68 upper a-arms w/the later BJ's. I connected the steering arms to the tie-rods w/a 72 center-link on one truck & on my other one I just went ahead & used all 73-up steering gear cause the 73-up center-link was easier to find @ a wrecking yard.

You da man

Thanks again

jkade · 06-13-2007, 08:58 AM

SCOTI · 06-13-2007, 09:02 AM

Without knowing if a 'qualified' person did the welding..... it's hard to say. It does look kind of rusty & that would be a concern for me.

What parts complete this 'kit'? What R&P does it use?

gringoloco · 06-13-2007, 09:07 AM

With it being cut that way, you will have to fab engine mounts.

jkade · 06-13-2007, 09:18 AM

Quote:

Originally Posted by SCOTI

Without knowing if a 'qualified' person did the welding..... it's hard to say. It does look kind of rusty & that would be a concern for me.

What parts complete this 'kit'? What R&P does it use?

Quote:

Originally Posted by gringoloco

With it being cut that way, you will have to fab engine mounts.

Scoti, that was my thought also. He said it was setup for mustangII r&p.

Gringo, that is what I figured since it is cut that way, I guess I could buy some of them universal mounts for a ls1 and cut them down.

He wants $225 for the cross and $175 for the tubular lowers.

onetonk5 · 06-13-2007, 10:20 AM

Jkade...if you dont use the tube lower arms will you let me know if there still available. Do you know what brand they are?
Thanks
Mark

jkade · 06-13-2007, 10:44 AM

Name: misc038_320x240.jpg
Views: 212
Size: 44.1 KB

Name: misc041_320x240.jpg
Views: 215
Size: 42.3 KB

Name: misc044_320x240.jpg
Views: 219
Size: 48.4 KB

This is the lower contol arms.

jkade · 06-13-2007, 10:45 AM

Quote:

Originally Posted by onetonk5

Jkade...if you dont use the tube lower arms will you let me know if there still available. Do you know what brand they are?
Thanks
Mark

I will let you know if I don't buy them.

Anyone figure what brand they are???

onetonk5 · 06-13-2007, 10:59 AM

Is the balljoint replaceable? Never seen a set like those.

fastbagged68 · 06-13-2007, 02:59 PM

Those are Bill Turners Arms... they look a little different then mine though. If you want more pics of those crossmembers and control arms do a search in the suspension forum for Crossmember drop....It is probably the longest thread of all time!!!

jkade · 06-13-2007, 03:47 PM

Quote:

Originally Posted by fastbagged68

Those are Bill Turners Arms... they look a little different then mine though. If you want more pics of those crossmembers and control arms do a search in the suspension forum for Crossmember drop....It is probably the longest thread of all time!!!

Reckon bill did the cross member also???

06-12-2007, 08:59 PM	#1
jkade Senior Member Join Date: Nov 2005 Location: AL Posts: 2,519	Will this work??? I may have found a deal on some tubular lower control arms and a 73-87 crossmember that a guy bought with a project truck and he isn't going to use any of it. The crossmember has been cut and set up for a rack and the tubular lower arms are new with balljoints and are for a 87 down. Will my spindles work with this? I would buy some tubular uppers also to match the lowers, so would I buy for 72 or 87 down?

06-12-2007, 09:04 PM	#2
GREASEMONKEY72 Registered User Join Date: Aug 2006 Location: Bakersfield,CA Posts: 7,893	Re: Will this work??? i dont think the spindles fit the 73+ a-arms but i could be wrong __________________ -steven Alte Seele S.S. "Allison" '72 C/10 LWB 350SB/TH350 - DD PITBULL IS NOT A CRIME

06-12-2007, 11:15 PM	#4
SCOTI Registered User Join Date: Apr 2001 Location: DALLAS,TX Posts: 22,031	Re: Will this work??? Spindles will interchange if the correct year ball joints are used (73-87 spindles need 73-87 BJ's; 71-72 spindles need 71-72 stuff etc...). Again.... same for the upper tubular arm question. Just get the right BJ for your spindle & it will bolt in to a later style a-arm. I used 73-up disc brake spindles on my 68 lower a-arms using the later BJ.s. I used the 68 upper a-arms w/the later BJ's. I connected the steering arms to the tie-rods w/a 72 center-link on one truck & on my other one I just went ahead & used all 73-up steering gear cause the 73-up center-link was easier to find @ a wrecking yard. __________________ 67SWB-B.B.RetroRod 64SWB-Recycle 89CCDually-Driver/Tow Truck 99CCSWB Driver All Fleetsides @rattlecankustoms in IG Building a small, high rpm engine with the perfect bore, stroke and rod ratio is very impressive. It's like a highly skilled Morrocan sword fighter with a Damascus Steel Scimitar..... *Cubic inches is like Indiana Jones with a cheap pistol.*

06-12-2007, 11:18 PM	#5
GREASEMONKEY72 Registered User Join Date: Aug 2006 Location: Bakersfield,CA Posts: 7,893	Re: Will this work??? well that answers it for both of us^ __________________ -steven Alte Seele S.S. "Allison" '72 C/10 LWB 350SB/TH350 - DD PITBULL IS NOT A CRIME

06-13-2007, 08:58 AM	#7
jkade Senior Member Join Date: Nov 2005 Location: AL Posts: 2,519	Re: Will this work??? http://i20.photobucket.com/albums/b2...sc/misc053.jpg http://i20.photobucket.com/albums/b2...sc/misc049.jpg http://i20.photobucket.com/albums/b2...sc/misc050.jpg http://i20.photobucket.com/albums/b2...sc/misc051.jpg http://i20.photobucket.com/albums/b2...sc/misc052.jpg http://i20.photobucket.com/albums/b2...sc/misc048.jpg http://i20.photobucket.com/albums/b2...sc/misc047.jpg http://i20.photobucket.com/albums/b2...sc/misc046.jpg Does it look like it is worth messing with??? It hasn't been cut the way you all do it has it??

06-13-2007, 09:02 AM	#8
SCOTI Registered User Join Date: Apr 2001 Location: DALLAS,TX Posts: 22,031	Re: Will this work??? Without knowing if a 'qualified' person did the welding..... it's hard to say. It does look kind of rusty & that would be a concern for me. What parts complete this 'kit'? What R&P does it use? __________________ 67SWB-B.B.RetroRod 64SWB-Recycle 89CCDually-Driver/Tow Truck 99CCSWB Driver All Fleetsides @rattlecankustoms in IG Building a small, high rpm engine with the perfect bore, stroke and rod ratio is very impressive. It's like a highly skilled Morrocan sword fighter with a Damascus Steel Scimitar..... *Cubic inches is like Indiana Jones with a cheap pistol.*

06-13-2007, 09:07 AM	#9
gringoloco A guy with a truck Join Date: Sep 2005 Location: Germany, for now Posts: 5,921	Re: Will this work??? With it being cut that way, you will have to fab engine mounts. __________________ -Chris Instagram _elgringoloco_ '70 Short-Wide How to: Ruin a perfectly good C10 ‘70 Blazer ConversionHow To: Ruin a Perfectly Good 4wd '72 Highlander How To: Ruin a Perfectly Good K/5 (SOLD) '72 Blazer 2WD How to: Ruin a perfectly good Blazer (SOLD) '05 Yukon Daily Driven (not so stock) Yukon (SOLD) ‘07 Yukon Denali (daily) Members met list: SCOTI, darkhorse970, 67cheby, 67cheby'sGirl, klmore, porterbuilt, n2billet, Fastrucken, classicchev, Col Clank, GSFMECH, HuggerCST, Spray-Bomb, BACKYARD88, 5150, fine69, fatbass, smbrouss70, 65StreetCruiser, GAc10boy

06-13-2007, 10:20 AM	#11
onetonk5 Cereal Killer Join Date: Jan 2006 Location: Montgomery, Alabama Posts: 639	Re: Will this work??? Jkade...if you dont use the tube lower arms will you let me know if there still available. Do you know what brand they are? Thanks Mark __________________ If I dont do it....somebody else will.

06-13-2007, 10:44 AM	#12
jkade Senior Member Join Date: Nov 2005 Location: AL Posts: 2,519	Re: Will this work??? This is the lower contol arms.

06-13-2007, 10:59 AM	#14
onetonk5 Cereal Killer Join Date: Jan 2006 Location: Montgomery, Alabama Posts: 639	Re: Will this work??? Is the balljoint replaceable? Never seen a set like those. __________________ If I dont do it....somebody else will.

06-13-2007, 02:59 PM	#15
fastbagged68 Registered User Join Date: Jun 2002 Location: Tri Valley California Posts: 792	Re: Will this work??? Those are Bill Turners Arms... they look a little different then mine though. If you want more pics of those crossmembers and control arms do a search in the suspension forum for Crossmember drop....It is probably the longest thread of all time!!!

Thread Tools
Show Printable Version Email this Page
Display Modes
Linear Mode Switch to Hybrid Mode Switch to Threaded Mode



Register or Log In To remove these advertisements.

Register or Log In To remove these advertisements.