|
Register or Log In To remove these advertisements. |
|
|
|
|||||||
 |
|
|
Thread Tools | Display Modes |
05-01-2002, 09:51 PM
|
#1 |
|
Account Suspended
Join Date: May 2000
Location: IL
Posts: 0
|
corvette ram horn pass side for 50 buck ?
is #3932461 ram horn for 50 bucks and coe s with a passenger car driver angled manifold too a decent deal you think ?
new ram vette ones are at least 75 each new,. so.,, what do you think ? ------------------ Randy- Lincoln, IL randy@ccaonline.com 2177353230 -71 C-10 350/CH465/3.07, basketcase literally, am assembling now -84 Z28 5.0L/700R4/3.73 daily driver -84 Firebird/SE 2.8L/T-5/3.73/engine bad, dammit,, -82 purple Trans Am, ram hood, junk305/good THM200C **I buy/sell/hoard/trade most any GM vehicle parts of any and all kinds -parting out: '81 Cutlass Supreme Brougham *Paint is overrated © RSS Enterprises 2000 |
|
|
|
05-02-2002, 05:16 AM
|
#2 |
|
user # 2756
 
Join Date: Jun 2001
Location: Chesapeake, Virginia
Posts: 4,612
|
Fast, I just paid $86 a piece for my 62 vette ramhorns(center dump) from gmpartsdirect. $203 total w/ shipping/handling. Now finding the time to get them on......
------------------ 1970 GMC K25 Custom Chesapeake, VA My 70 GMCor Webshots http://community.webshots.com/user/70gmc
__________________
1970 K25, 8' stepside bed 350/465/205 44 up front, 60 in the rear 4.10s rolling on 33" Dunlop MTs 1986 K5, 350/465/208 Dana 60/14 bolt from a cucv 36" Super Swampers TSL/SX 1983 K20 w/ CUCV axles, 350/700R4/208 sitting on 37" Goodyears 1986 M1031 6.2 diesel, TH400/NP205 locker in the rear and a LS in the front, all stock for now..... 1986 K30, 350/400/205 dana 60 and 14 bolt. I kept the drivetrain. Body/bad and chassis are gone. 1981 K30, 350/465/205 dana 60 and dually 14 bolt. Has a G80, and a flat bed. Going to replace the flat bed. 1985 K20, 350/400/208 10 bolt and SF 14 bolt. I wonder where I can find some 1 tons. Hmmmmm 
|
|
|
|
|
05-02-2002, 08:34 AM
|
#3 |
|
Registered User
Join Date: Dec 1999
Location: Austin, TX, USA
Posts: 7,727
|
I'm not a casting numbers type guy, but make sure it is a 2 1/2" manifold as not ALL 'vettes were. Only the 300+ hp cars from 62 to about 71. After that most were 2" except L-82 cars.
------------------ 70 GMC 3/4 ton Sierra Grande 402/TH400 72 Jimmy 4WD 4spd 4" & 35's 64 Corvette Coupe 68 Camaro 'vert TPI & TH700 69 Z/28 355 12.6's @110 72 Datsun 240Z-ol' reliable
__________________
44 Willys MB 52 M38A1 64 Corvette Coupe 68 Camaro 'vert LT1 & TH700 69 Z/28 355 12.6's @110 69 Chevy Short Step 4 1/2"/7" drop 72 Jimmy 4WD 4spd 4" & 35's 02 GMC 2500HD 4x4 Duramax |
|
|
|
|
05-02-2002, 02:50 PM
|
#4 |
|
Account Suspended
Join Date: May 2000
Location: IL
Posts: 0
|
true
im gonna do more investigating on the numbers to make sure, online gotta stay under 86 for each then to get decent deal it looks like, ive never had any 2.5 ones yet, maybe i will have one or two now for use on truck, i hope,, thanks ------------------ Randy- Lincoln, IL randy@ccaonline.com 2177353230 *many GM parts bought, traded, or sold -am parting out: '81 Cutlass Supreme Brougham current fleet: -71 C-10 350/CH465/3.07- basketcase -84 Z28 5.0L/700R4/3.73 daily driver -84 Firebird/SE 2.8L/T-5/3.73/engine bad -82 purple Trans Am, project #2 *Paint is overrated* © RSS Enterprises 2000 |
|
|
|
|
| Bookmarks |
| Thread Tools | |
| Display Modes | |
|
|
Linear Mode
