Transfer case part question - The 1947 - Present Chevrolet & GMC Truck Message Board Network

CheyLadd · 10-28-2007, 10:20 AM

The fitting for the speedometer cable on the piece that bolts to the rear of my 205 transfer case is a mess and is leaking a bunch of oil. First, what is this part called, and second, anyone know where I can get one? Is this a part I can get at napa? I am assuming I need to replace the whole piece and not just the speedometer input portion. If wrong, please let me know. I haven't torn it apart yet. Thanks. BTW, the truck is a 72 k10 swb.

**Yukon Jack** · 10-28-2007, 04:07 PM

I'm not seeing it on this link but go here and give these guys a call http://quad4x4.com/New%20Process%20N...fer%20Case.htm

CheyLadd · 10-28-2007, 04:18 PM

I should have pulled it apart before I asked. The prior owner had put a gob of sealant around the fitting. After getting all of that off, I took it apart and it was simply missing an o-ring. Problem fixed. Wish they were all that easy.

SoCal71K20 · 11-10-2007, 11:11 AM

Sorry for the late reply. Checkout www.norcalbigdawgs.net/Gallery/album49
Anyhow, if that site doesn't come up, you need GM # 326561 Sleeve. Rubber part of sleeve will wear out over time and cause fluid leak at this point. Real easy to change out. Good luck.

CheyLadd · 11-10-2007, 01:27 PM

Socal. Thanks. I finally get it. I have been trying to seal the speedo cable thinking it was missing something. I will get the part ordered.

10-28-2007, 10:20 AM	#1
CheyLadd Registered User Join Date: Oct 2006 Location: Glendora, CA Posts: 85	Transfer case part question The fitting for the speedometer cable on the piece that bolts to the rear of my 205 transfer case is a mess and is leaking a bunch of oil. First, what is this part called, and second, anyone know where I can get one? Is this a part I can get at napa? I am assuming I need to replace the whole piece and not just the speedometer input portion. If wrong, please let me know. I haven't torn it apart yet. Thanks. BTW, the truck is a 72 k10 swb.

10-28-2007, 04:07 PM	#2
Yukon Jack Post Whore Join Date: Feb 2000 Location: Rose Hill, KS, USA Posts: 12,686	Re: Transfer case part question I'm not seeing it on this link but go here and give these guys a call http://quad4x4.com/New%20Process%20N...fer%20Case.htm __________________ 1970 Blazer with a 400 sbc and 4" lift 1980 Pontiac Trans Am, 455 Oldsmobile 2012 Kawasaki Concours 14

10-28-2007, 04:18 PM	#3
CheyLadd Registered User Join Date: Oct 2006 Location: Glendora, CA Posts: 85	Re: Transfer case part question I should have pulled it apart before I asked. The prior owner had put a gob of sealant around the fitting. After getting all of that off, I took it apart and it was simply missing an o-ring. Problem fixed. Wish they were all that easy.

11-10-2007, 11:11 AM	#4
SoCal71K20 Registered User Join Date: Jan 2002 Location: Lemon Grove, California Posts: 152	Re: Transfer case part question Sorry for the late reply. Checkout www.norcalbigdawgs.net/Gallery/album49 Anyhow, if that site doesn't come up, you need GM # 326561 Sleeve. Rubber part of sleeve will wear out over time and cause fluid leak at this point. Real easy to change out. Good luck.

11-10-2007, 01:27 PM	#5
CheyLadd Registered User Join Date: Oct 2006 Location: Glendora, CA Posts: 85	Re: Transfer case part question Socal. Thanks. I finally get it. I have been trying to seal the speedo cable thinking it was missing something. I will get the part ordered.

Thread Tools
Show Printable Version Email this Page
Display Modes
Linear Mode Switch to Hybrid Mode Switch to Threaded Mode



Register or Log In To remove these advertisements.

Register or Log In To remove these advertisements.