|
02-12-2008, 08:12 AM
|
#1 |
|
Registered User
Join Date: Jan 2007
Location: Puyallup, WA
Posts: 1,662
|
Panhard Nut Q
I had my panhard bar come off at the frame while I was cruzin' today. Luckily it happened a couple blocks from the house when I was returning. Can anyone tell me what size the nut is where the bar attaches to the frame? Thanks!
__________________
72 C10 lwb fleetside -stock 350/350 combo |
|
|
|
02-12-2008, 09:06 AM
|
#2 |
|
Old member
Join Date: Jan 2002
Location: Liberty, & Garden City S.C. , U.S.
Posts: 19,943
|
Re: Panhard Nut Q
The bar attaches right behind the driver's side wheel up on the frame. You will need a bolt too!
This is a p[icture of a new bar but it attaches at the same point. 
__________________
1971 LWB Custom, 6.0LS & 4L80E, Speedhut.com GPS speedometer & gauges with A/C. 20" Boss 338's Grey wheels 4 wheel disc brakes. My Driver Seeing the USA in a 71  Upstate SC GM Truck Club 2013,14 and 2016 Hot Rod Pour Tour http://upstategmtrucks.com/ Get out and drive the truck this summer and have some fun! It sucks not being able to hear! LWB trucks rule, if you don't think so measure your SWB! After talking to tech support at Air Lift I have found out that the kit I need is 60811. Per the measurements I gave them. Ride height of truck inside spring and inside diameter of springs. |
|
|
|
|
02-12-2008, 10:42 AM
|
#3 |
|
Registered User
Join Date: Jan 2007
Location: Puyallup, WA
Posts: 1,662
|
Re: Panhard Nut Q
Dang it, I forgot about the bolt. Well then, does anyone know what size nut and bolt I need??? Anyone...anyone?
__________________
72 C10 lwb fleetside -stock 350/350 combo |
|
|
|
|
02-12-2008, 09:37 PM
|
#4 |
|
Registered User
Join Date: Jan 2007
Location: Puyallup, WA
Posts: 1,662
|
Re: Panhard Nut Q
Ttt
__________________
72 C10 lwb fleetside -stock 350/350 combo |
|
|
|
|
02-12-2008, 10:22 PM
|
#5 |
|
Registered User
Join Date: Dec 2004
Location: beulah,alabama
Posts: 1,075
|
Re: Panhard Nut Q
i have a bare frame with the bolt and nut still in the bracket will look at in in a few minutes when i go over and work on my brakes today .
|
|
|
|
|
02-13-2008, 02:07 AM
|
#6 |
|
Registered User
Join Date: Oct 2007
Location: Sykesville MD
Posts: 357
|
Re: Panhard Nut Q
i wanna say 1/2 inch but let eyeh8 check to be certain
__________________
'55 3100 2nd series short-bed stepside '70 Corvette coupe stingray '71 Chevelle 2-dr coupe SS clone '71 C10 long-bed fleetside '83 long-haired brunette wife |
|
|
|
|
02-13-2008, 03:37 AM
|
#7 |
|
Registered User
Join Date: Jan 2007
Location: Puyallup, WA
Posts: 1,662
|
Re: Panhard Nut Q
Thanks guys. The truck is my DD so I need it back on the road ASAP. Anyone else know?
__________________
72 C10 lwb fleetside -stock 350/350 combo |
|
|
|
|
02-13-2008, 09:29 AM
|
#8 |
|
Registered User
Join Date: Jan 2007
Location: Puyallup, WA
Posts: 1,662
|
Re: Panhard Nut Q
Ttt
__________________
72 C10 lwb fleetside -stock 350/350 combo |
|
|
|
|
02-13-2008, 09:45 AM
|
#9 |
|
Registered User
Join Date: Dec 2004
Location: beulah,alabama
Posts: 1,075
|
Re: Panhard Nut Q
1/2 x 3 and a half course thread
|
|
|
|
 |
| Bookmarks |
| Thread Tools | |
| Display Modes | |
|
|
Linear Mode
