![]() |
![]() |
#1 |
Registered User
Join Date: Feb 2003
Location: Paragould, Ar
Posts: 571
|
Serpentine questions
I have a few questions about my serpentine setup which came off a 88 s-10.
#1 Do I need to have the idler that goes where the arrow is pointing? If so where can I get one? #2 How do I route the belt on this set-up? And does anyone have a part number that will work? I bought the belt for a 88 s-10 and it was way too short. Thank you for looking. If it wasnt for this website, I would have quit a long time ago.
__________________
1970 Gmc Grande Sierra Swb 2wd LSX (LQ4/4L80e) 1990 K1500 Daily ![]() |
![]() |
![]() |
![]() |
#2 |
Registered User
Join Date: Feb 2002
Location: Vacaville, CA
Posts: 2,746
|
Re: Serpentine questions
You do not need an extra idler pulley.
Look at the diagrams part way do this page for routing: http://www.2carpros.com/forum/1990-c...-vt132692.html For my belt I just ran a string and measured. Then got a belt that length. There are so many different serp bracket setups that its hard to do part numbers. What water pump are you using?
__________________
![]() ![]() 99 Pontiac S/C GTP, SLP Ram Air hood, GMPP Konis & springs 95 Neon ACR, MP PCM, AFX UDP, 3.0 CAI Last edited by neonlarry; 07-03-2008 at 05:17 PM. |
![]() |
![]() |
![]() |
#3 |
Lemme show you something!!
Join Date: Apr 2007
Location: St.Helens, OR.
Posts: 876
|
Re: Serpentine questions
When I did mine- I wasn't sure if I needed that pulley or not. The GMPP kit comes with it- so I figured I'd better get it. I got mine from the local stealership but the link below has them for about 10 bucks less. If you do use this idler- get a Gates #K060970 belt. If you opt not to use it.....I am no help to you, cause I don't know what the correct belt would be.
http://www.tpiparts.net/inc/sdetail/399
__________________
'67 CST-10 LWB ("Crusty") SOLD '67 GMC SWB ("Murdock") 2000 K1500 Suburban ("Betty") '95 BMW 325i ("Joy") |
![]() |
![]() |
![]() |
#4 |
Hollister Road Co.
Join Date: Apr 2005
Location: Houston
Posts: 6,134
|
Re: Serpentine questions
I think you could get away with out it but with it you have that much more belt contact with the pulley. If you didn't have A/C I'd go without. I have the same setup on mine and I used the idler. I used a K060935 belt and then a 940 which is 1/2 shorter than a 935
Last edited by dwcsr; 07-03-2008 at 06:51 PM. |
![]() |
![]() |
![]() |
#5 |
MY EX DRIVES A BROOM
Join Date: Nov 2003
Location: Herington, KS
Posts: 869
|
Re: Serpentine questions
good info
__________________
They say nobody's perfect. I'm a nobody, so I must be perfect. Building Nemo -1968 C10 Long Bed FRED -1947 KB-2 International |
![]() |
![]() |
![]() |
#6 | |
Registered User
Join Date: Feb 2003
Location: Paragould, Ar
Posts: 571
|
Re: Serpentine questions
Quote:
__________________
1970 Gmc Grande Sierra Swb 2wd LSX (LQ4/4L80e) 1990 K1500 Daily ![]() |
|
![]() |
![]() |
![]() |
#7 |
Registered User
Join Date: Mar 2003
Location: Uvalde, Tx
Posts: 407
|
Re: Serpentine questions
jackyl9999, I'm also in the process of installing a serpentine system in my truck. What A/C compressor are you using with your setup?
__________________
1969 C/10 Longbed undergoing rebuild. Old Chevy's Never Die, They Just Rust Around The Edges |
![]() |
![]() |
![]() |
#8 |
Registered User
Join Date: Feb 2003
Location: Paragould, Ar
Posts: 571
|
Re: Serpentine questions
http://www.oldairproducts.com/catalo...00000_69000003I got it from old aire. They offer them for a serpentine.
__________________
1970 Gmc Grande Sierra Swb 2wd LSX (LQ4/4L80e) 1990 K1500 Daily ![]() |
![]() |
![]() |
![]() |
#9 |
Registered User
Join Date: Mar 2003
Location: Uvalde, Tx
Posts: 407
|
Re: Serpentine questions
Thanks for the 411
__________________
1969 C/10 Longbed undergoing rebuild. Old Chevy's Never Die, They Just Rust Around The Edges |
![]() |
![]() |
![]() |
Bookmarks |
Thread Tools | |
Display Modes | |
|
|