need help with horn - The 1947 - Present Chevrolet & GMC Truck Message Board Network

254steele · 07-17-2008, 11:35 PM

Just bought a '67 stepside last week. The previous owner "installed" a Grant steering wheel (note quotes). The horn isn't hooked up. It works when tested, and the factory connector still exists next to the fuse box. My problem is twofold:
1. I cannot, for the life of me, figure out which wires in the steering column are supposed to end at the connector (which no longer exists) to plug into the horn wires.
2. I have no way of knowing whether the horn switch on the Grant wheel is good, or where the connection to the horn switch is made. Neither my Haynes or Chilton manuals mention the horn at all.
Please save me from a tacky aftermarket horn mounted in a place no horn should be!

254steele · 07-21-2008, 08:42 AM

Really really need help with this-please?

d10s69c10 · 07-21-2008, 11:19 AM

Well as far as finding out the wires "fishing" i would go thru with a multi meter and find the ( O/L ) open line. wich more than likely with your horn not engaged would be it. if horn was engaged it should show either voltage or some odd amount of ohms.

254steele · 07-21-2008, 12:07 PM

after revisiting this with intent to test, every single wire that i can find goes directly to the instrument panel. i guess i need to figure out how to rewire the steering column from scratch. any suggestions? i did see the posts on stock wheels and i think i have the wheel wired right at this point. where is the connection made between horn wire (from fuse box) and wheel? that's where i'm lost.

BLACK AND BLUE 67-72 · 07-21-2008, 01:58 PM

it goes through the turn signal harness, it is connected to the brass looking button

BLACK AND BLUE 67-72 · 07-21-2008, 02:11 PM

see the little brass looking post sticking up

254steele · 07-27-2008, 11:37 AM

thanks for the reply. is this piece under a metal plate that the steering wheel is screwed onto? if not, i have to track one of these down.

BLACK AND BLUE 67-72 · 07-27-2008, 12:25 PM

Yes it is in your column under the aluminum plate that the wheel bolts to, there should be a round plastic piece that is under the metal piece also. There should be an aluminum pin sticking up see the black contact, it will go through the hole in the aluminum plate.

254steele · 07-29-2008, 06:39 PM

Thanks a million times over for the pics. I don't have this part...time to start searching. Any suggestions?

07-17-2008, 11:35 PM	#1
254steele Registered User Join Date: Jul 2008 Location: waco, tx Posts: 8	need help with horn Just bought a '67 stepside last week. The previous owner "installed" a Grant steering wheel (note quotes). The horn isn't hooked up. It works when tested, and the factory connector still exists next to the fuse box. My problem is twofold: 1. I cannot, for the life of me, figure out which wires in the steering column are supposed to end at the connector (which no longer exists) to plug into the horn wires. 2. I have no way of knowing whether the horn switch on the Grant wheel is good, or where the connection to the horn switch is made. Neither my Haynes or Chilton manuals mention the horn at all. Please save me from a tacky aftermarket horn mounted in a place no horn should be!

07-21-2008, 08:42 AM	#2
254steele Registered User Join Date: Jul 2008 Location: waco, tx Posts: 8	Re: need help with horn Really really need help with this-please? __________________ 254steele 1967 short stepside--new project 2000 ext cab short bed--daily driver

07-21-2008, 11:19 AM	#3
d10s69c10 Built 4 Speed Join Date: May 2008 Location: Geneva FL Posts: 619	Re: need help with horn Well as far as finding out the wires "fishing" i would go thru with a multi meter and find the ( O/L ) open line. wich more than likely with your horn not engaged would be it. if horn was engaged it should show either voltage or some odd amount of ohms. __________________ 1969 C/10 Short Box: 496/T-56 in worx. "To Be Old And Wise, First You Must Be Young And Stupid"

07-21-2008, 12:07 PM	#4
254steele Registered User Join Date: Jul 2008 Location: waco, tx Posts: 8	Re: need help with horn after revisiting this with intent to test, every single wire that i can find goes directly to the instrument panel. i guess i need to figure out how to rewire the steering column from scratch. any suggestions? i did see the posts on stock wheels and i think i have the wheel wired right at this point. where is the connection made between horn wire (from fuse box) and wheel? that's where i'm lost. __________________ 254steele 1967 short stepside--new project 2000 ext cab short bed--daily driver

07-21-2008, 01:58 PM	#5
BLACK AND BLUE 67-72 Firefighter Join Date: Feb 2001 Location: Yellville, Ar, USA Posts: 1,943	Re: need help with horn it goes through the turn signal harness, it is connected to the brass looking button __________________ '72 Chevy SWB 350 Auto '67 GMC LWB 350 4 speed '70 Chevy 4x4 Stepside 350 Auto Yellville, Ar. USA

07-21-2008, 02:11 PM	#6
BLACK AND BLUE 67-72 Firefighter Join Date: Feb 2001 Location: Yellville, Ar, USA Posts: 1,943	Re: need help with horn see the little brass looking post sticking up Attached Images __________________ '72 Chevy SWB 350 Auto '67 GMC LWB 350 4 speed '70 Chevy 4x4 Stepside 350 Auto Yellville, Ar. USA Last edited by BLACK AND BLUE 67-72; 07-21-2008 at 02:11 PM.

07-27-2008, 11:37 AM	#7
254steele Registered User Join Date: Jul 2008 Location: waco, tx Posts: 8	Re: need help with horn thanks for the reply. is this piece under a metal plate that the steering wheel is screwed onto? if not, i have to track one of these down. __________________ 254steele 1967 short stepside--new project 2000 ext cab short bed--daily driver

07-27-2008, 12:25 PM	#8
BLACK AND BLUE 67-72 Firefighter Join Date: Feb 2001 Location: Yellville, Ar, USA Posts: 1,943	Re: need help with horn Yes it is in your column under the aluminum plate that the wheel bolts to, there should be a round plastic piece that is under the metal piece also. There should be an aluminum pin sticking up see the black contact, it will go through the hole in the aluminum plate. Attached Images __________________ '72 Chevy SWB 350 Auto '67 GMC LWB 350 4 speed '70 Chevy 4x4 Stepside 350 Auto Yellville, Ar. USA

07-29-2008, 06:39 PM	#9
254steele Registered User Join Date: Jul 2008 Location: waco, tx Posts: 8	Re: need help with horn Thanks a million times over for the pics. I don't have this part...time to start searching. Any suggestions? __________________ 254steele 1967 short stepside--new project 2000 ext cab short bed--daily driver

Thread Tools
Show Printable Version Email this Page
Display Modes
Linear Mode Switch to Hybrid Mode Switch to Threaded Mode



Register or Log In To remove these advertisements.

Register or Log In To remove these advertisements.