Register or Log In To remove these advertisements. |
|
|
|
Thread Tools | Display Modes |
08-02-2008, 08:53 PM | #1 |
Registered User
Join Date: May 2008
Location: san antonio, texas
Posts: 412
|
how many quarts does my tranny take?
i drained it out and put in a new filter and gasket!
i have a th350, how many quarts do i need to put in? |
08-02-2008, 08:55 PM | #2 |
Registered User
Join Date: Aug 2006
Location: Georgia
Posts: 850
|
Re: how many quarts does my tranny take?
|
08-02-2008, 11:14 PM | #3 |
Senior Member
Join Date: Jan 2003
Location: daytonabeach
Posts: 22,956
|
Re: how many quarts does my tranny take?
when you change filter and pan gasket the tranny doesnt drain completely normally 3-5quarts will be required to top off// i normally catch what comes out and count how many quarts came out and start there
__________________
71c-10 350/2004r/4:11 lowered3/4 longbed/dead by hurricane MEANING OF DEATH::::: SOMEBODY ELSE GETS YOUR STUFF DONT BELIEVE EVERYTHING YOU THINK TAKE MY ADVISE;I DON'T USE IT ANYWAY |
08-03-2008, 12:18 AM | #4 |
20' Daredevil (Ret)
Join Date: May 2003
Location: Jefferson State
Posts: 13,722
|
Re: how many quarts does my tranny take?
I just replaced the pan gasket (and filter) on my TH350 last week. I added four quarts, and it was exactly on the 'full' mark after getting it up to operating temperature (idling in Park on a level slab).
Dang, after reading what I wrote, I need to edit this again. What I did was add 4 quarts, then started the engine and let it warm up a bit while I checked for leaks. Then I drove a couple miles to a car wash and cleaned the truck and the engine -- then drove home and checked the trans fluid. It was on the 'full' mark. Whew, hope I got that right this time! Edit: I was gonna check how much came out, but it had been sitting (and leaking) for awhile, and I only drained about 1 1/2 quarts.
__________________
- Mike - 1972 K20 LWB 350/350/205 RIP El Jay Last edited by Stocker; 08-03-2008 at 12:27 AM. |
08-03-2008, 12:22 AM | #5 |
its all about the +6 inches
Join Date: Jan 2001
Location: Hilliard Ohio
Posts: 2,690
|
Re: how many quarts does my tranny take?
i was thinking it was in the 4 quarts area.
I say start with 3... it is WAY easier to add, than it is to drain. Also (not knowing how much you know on the subject) to dump a quart or two in there, then fire up the truck, run it through the gears slowly pausing at each selection, and then pour in the 3rd one. Go thorugh the gears again and check the level on the stick. Add accordingly. With the engine and tranny cold, you don't want to bring it to the full line... rather just up past the add line. Then go around the block a few times, and then check it again... after going through all the gears, pausing in each selection... then you can bring it to the full position. |
08-03-2008, 12:35 AM | #6 |
Son of a gun
Join Date: Jan 2007
Location: Hot Springs, Arkansas
Posts: 1,636
|
Re: how many quarts does my tranny take?
4 in the pan. 2 in the converter...you won't have to worry about those two though if you are just dropping the pan
__________________
Bill BEATERS ARE NEATER |
Bookmarks |
Thread Tools | |
Display Modes | |
|
|