![]() |
Register or Log In To remove these advertisements. |
|
|
![]() |
|
Thread Tools | Display Modes |
![]() |
#1 |
Registered User
Join Date: Jan 2008
Location: Raleigh, NC
Posts: 321
|
Plate under Stock Intake Removal
Anyone know how to remove the plate under the stock 4 barrel intake? Looks like it is riveted in?
|
![]() |
![]() |
![]() |
#2 |
too many toys
Join Date: Oct 2004
Location: winnipeg sorta
Posts: 63
|
Re: Plate under Stock Intake Removal
Slot them with a thin cutting disc on a hand grinder or ig your steady with a hack saw. Then wack em with an impact driver to loosen.They are spiral rivets but do come out.
__________________
![]() ![]() 1971 gmc 3/4 4x4 383 stroked 1968 1/2 2nd owner 4bbl 6cyl 1969 gmc 3/4 4 sale 350 4bbl 4spd 1969 chev 1/2 lowered 5 spd 454 4bbl 1947 chev coupe 2002 harley flhtcui 6 -67-72 my parts |
![]() |
![]() |
![]() |
#3 |
Senior Member
Join Date: Jan 2003
Location: daytonabeach
Posts: 22,956
|
Re: Plate under Stock Intake Removal
pretty foolish to remove that plate its there to prevent oil being splashed on the hot intake removing will cause sludge formation
__________________
71c-10 350/2004r/4:11 lowered3/4 longbed/dead by hurricane MEANING OF DEATH::::: SOMEBODY ELSE GETS YOUR STUFF DONT BELIEVE EVERYTHING YOU THINK TAKE MY ADVISE;I DON'T USE IT ANYWAY |
![]() |
![]() |
![]() |
#4 |
Registered User
Join Date: Jan 2008
Location: Raleigh, NC
Posts: 321
|
Re: Plate under Stock Intake Removal
want to remove it for cleaning purpose.
|
![]() |
![]() |
![]() |
#5 |
Registered User
Join Date: Jan 2008
Location: Raleigh, NC
Posts: 321
|
Re: Plate under Stock Intake Removal
This is why I wanted to remove the cover and clean in there. Thanks for the help.
|
![]() |
![]() |
![]() |
#6 |
Senior Member
![]() Join Date: Sep 2005
Location: Lewisville, Nc
Posts: 10,234
|
Re: Plate under Stock Intake Removal
holy cow!!!
__________________
David fuller Ase Certified Mechanic Click here to help support our board!! 1971 Chevy c-10 under going a 4.8l LSx swap Build Thread http://67-72chevytrucks.com/vboard/s...d.php?t=421305 2007 Honda Accord my daily 145kmiles 2002 Honda Accord 4 door With 330k(sisters car) 2005 toyota Avalon 228k( brothers car) 2002 Sububran 5.3 245k 2000 Tahoe 5.3l 378 General manager for Marco's Carwash & lube |
![]() |
![]() |
![]() |
#7 |
Senior Member
Join Date: Jul 2001
Location: Muskegon,MI,USA
Posts: 6,026
|
Re: Plate under Stock Intake Removal
I tap the four holes with a 8-24 tap and use stainless screws to hold the plate on. The tap will bottom out so the last few threads are not cut completely so the screws will lock in place when tightened up.
Jim
__________________
1971 Shortbox step side 4x4, 350 sbc, 3:07 rear end 1965 Impala SS 400 sbc, Muncie rock crusher 1966 Impala SS 396 bbc, TH 400 1969 El Camino, 350 sbc, TH 350 1971 Snowplow built on a Blazer frame 1972 GMC Short bed, stepside, TH 400, 427 BBC |
![]() |
![]() |
![]() |
#8 |
Active Member
![]() Join Date: Dec 2003
Location: Waterbury, CT
Posts: 591
|
Re: Plate under Stock Intake Removal
I know this is late because you already have the cover off. When I removed mine I just used a sharp chisel under the head of the rivet and it popped right out. Replaced the rivets in the same hole they came out of . Had to hammer them back in so think they will stay in place.
|
![]() |
![]() |
![]() |
#9 |
blood type; Retumbo
Join Date: Jan 2004
Location: next to my reloading bench
Posts: 10,269
|
Re: Plate under Stock Intake Removal
Moroso and Milodon have a super slick tray to take its place. it keeps the lifters in place in the event of a catastrophic valve train failure. it uses 2 spring steel strips between it and the intake to hold it down. I think they go for about $30.
found it http://www.milodon.com/oil-system/pa...ter-baffle.asp Last edited by 68C15; 10-25-2008 at 10:41 PM. |
![]() |
![]() |
![]() |
Bookmarks |
Thread Tools | |
Display Modes | |
|
|