|
Register or Log In To remove these advertisements. |
|
|
|
|||||||
 |
|
|
Thread Tools | Display Modes |
12-07-2008, 12:33 AM
|
#1 |
|
Registered User
Join Date: Jun 2007
Location: Boca Raton, FL
Posts: 476
|
Are these drop spindles?
I bought these on somebodies word that they were 3" Belltechs, but now I'm hoping I didn't get ripped. The only markings are C10 LH / C10 RH. I'm second guessing if these are even drop spindles let alone Belltechs. If the shaft is centered and not towards the bottom they are drop spindles right????
  
Last edited by chevychase; 12-07-2008 at 02:49 AM. |
|
|
|
12-07-2008, 12:35 AM
|
#2 |
|
Registered User
Join Date: Jun 2008
Location: South Florida
Posts: 11,375
|
Re: Did I get ripped on these spindles?
I missed you tonight at fuddruckers at car cruise....Did you forget?
Those spindles look old...Cant tell if they are stock.
__________________
Get your facts first, and then you can distort them as much as you please!!!!!. Sylvester's build thread >>>http://67-72chevytrucks.com/vboard/s...ht=big+rebuild |
|
|
|
|
12-07-2008, 12:40 AM
|
#3 | |
|
Registered User
Join Date: Jun 2007
Location: Boca Raton, FL
Posts: 476
|
Re: Did I get ripped on these spindles?
Quote:
|
|
|
|
|
|
12-07-2008, 12:41 AM
|
#4 |
|
PROJECT 7DEUCE
 
Join Date: Dec 2002
Location: GRANTS PASS OR
Posts: 21,606
|
Re: Did I get ripped on these spindles?
That spindle looks centered...
__________________
GO BIG GREEN  GO DUCKSMEMBER #6377 72 k-5 daily driver 6'' lift 35'' 350-350-205 slowly getting rust free. Project "7DEUCE" check out my build http://67-72chevytrucks.com/vboard/s...d.php?t=267665 Tim Powell..R.I.P EastSideLowlife..... R.I.P.. |
|
|
|
|
12-07-2008, 12:47 AM
|
#5 |
|
Registered User
Join Date: Jun 2007
Location: DFW (Forney)
Posts: 1,529
|
Re: Did I get ripped on these spindles?
They "look" like dropped spindles.
__________________
'58 SWB Fleetside...Front & Rear Porterbuilt Dropmember, 6.0 LS /4L60E. Accuair E-level, 20 Billet Specialties (Vintecs) '63 Buick Riviera ... AccuAir E-level, 20" Billet Specialties (Vintecs) http://67-72chevytrucks.com/vboard/s...=528853&page=5 |
|
|
|
|
12-07-2008, 12:48 AM
|
#6 |
|
Active Member
Join Date: Aug 2008
Location: Washington
Posts: 147
|
Re: Did I get ripped on these spindles?
They look like drop spindles to me too.
|
|
|
|
|
12-07-2008, 01:14 AM
|
#7 |
|
Registered User
Join Date: Oct 2006
Location: Dundee, Oregon
Posts: 311
|
Re: Did I get ripped on these spindles?
My 3" spindles have the "bell tech" logo cast into them and a part number cast into them.
|
|
|
|
|
12-07-2008, 03:44 AM
|
#8 |
|
Registered User
Join Date: Apr 2007
Location: Kelso, WA
Posts: 363
|
Re: Did I get ripped on these spindles?
Yes, they are drop spindles... and 3" looks right. But the spindles look hella old or someone just didn't paint em before a previous install... IDK
__________________
1972 K10 4" lift, 35’s, 383 stroker, 700r4, current project. 1971 C10 3"/5" static drop, 355/350. "La Bamba.” The current daily driver. |
|
|
|
|
12-07-2008, 11:06 AM
|
#9 |
|
Old member
Join Date: Jan 2002
Location: Liberty, & Garden City S.C. , U.S.
Posts: 19,945
|
Re: Did I get ripped on these spindles?
Measure them and see where the spindal is from the top in relation to the bottom of the holes for mounting it.
Center of spindal to top and bottom. Now as far as the make you may find something after they are cleaned up.
__________________
1971 LWB Custom, 6.0LS & 4L80E, Speedhut.com GPS speedometer & gauges with A/C. 20" Boss 338's Grey wheels 4 wheel disc brakes. My Driver Seeing the USA in a 71  Upstate SC GM Truck Club 2013,14 and 2016 Hot Rod Pour Tour http://upstategmtrucks.com/ Get out and drive the truck this summer and have some fun! It sucks not being able to hear! LWB trucks rule, if you don't think so measure your SWB! After talking to tech support at Air Lift I have found out that the kit I need is 60811. Per the measurements I gave them. Ride height of truck inside spring and inside diameter of springs. |
|
|
|
|
12-07-2008, 12:37 PM
|
#10 |
|
Registered User
Join Date: Jan 2008
Location: Mt. Auburn, Il
Posts: 127
|
Re: Did I get ripped on these spindles?
Here are pics of factory C10 disc spindles. Yours look lowered.
|
|
|
|
|
12-07-2008, 12:47 PM
|
#11 |
|
WTB:Patience and Talent
Join Date: Sep 2006
Location: Oklahoma
Posts: 119
|
Re: Did I get ripped on these spindles?
Here's belltech 3" drops.
__________________
69 shortwide |
|
|
|
|
12-07-2008, 12:49 PM
|
#12 |
|
WTB:Patience and Talent
Join Date: Sep 2006
Location: Oklahoma
Posts: 119
|
Re: Did I get ripped on these spindles?
And heres where Belltech is stamped.
__________________
69 shortwide |
|
|
|
|
12-07-2008, 01:42 PM
|
#13 |
|
Senior Member
Join Date: Nov 2000
Location: WI,USA
Posts: 495
|
Re: Did I get ripped on these spindles?
Don't look like belltech's to me!!
__________________
69 Lwb C-10 402/700R4 70 Lwb C-10 250/3pd Wisc. |
|
|
|
|
12-07-2008, 01:43 PM
|
#14 |
|
Watch out for your cornhole !
Join Date: Jun 2003
Location: Azle, Texas
Posts: 14,162
|
Re: Did I get ripped on these spindles?
They're dropped spindles all right, but I'm pretty sure they're not Belltech.
I've put a bunch of Belltech spindles on and they have all been cast with the name on the back side. A 3 inch Belltech drop spindle should have the part number cast into them too, 3100 if I remember correctly. Western and Early Classic have their names on them too. Maybe Chassis Tech ?
__________________
I'm on the Instagram- @Gearhead_Kevin Last edited by Tx Firefighter; 12-07-2008 at 01:43 PM. |
|
|
|
|
12-07-2008, 02:07 PM
|
#15 |
|
Registered User
Join Date: Aug 2006
Location: Florida
Posts: 1,684
|
Re: Did I get ripped on these spindles?
I "think" djm has c10 stamped or cast on spindle.
__________________
1986 C10 SWB 6.0/6l90e Miami...Flee it like a native |
|
|
|
|
12-07-2008, 03:27 PM
|
#16 |
|
Registered User
Join Date: Jun 2007
Location: Boca Raton, FL
Posts: 476
|
Re: Did I get ripped on these spindles?
OK, thanks for ALL the replies and confirmations!
I had a brain freeze and thought the centered spindle meant stock. I'm cleaning these suckers up and will sanblast and paint this week. They're looking a little better with some scotch bright already. Definitely no other markings besides C10 LH/RH. 
|
|
|
|
|
12-07-2008, 07:21 PM
|
#17 |
|
Registered User
Join Date: Dec 2007
Location: Bloomington, Illinois
Posts: 9
|
Re: Did I get ripped on these spindles?
|
|
|
|
|
12-07-2008, 09:59 PM
|
#18 | |
|
Account Suspended
Join Date: Mar 2007
Location: san bernardino ca. everywhere
Posts: 3,938
|
Re: Did I get ripped on these spindles?
Quote:
|
|
|
|
|
|
12-07-2008, 10:05 PM
|
#19 |
|
Account Suspended
Join Date: Jun 2000
Location: over yonder
Posts: 14,270
|
Re: Did I get ripped on these spindles?
ECE has Early Classic cast into the back of them. Look like 2.5" AIM spindles for 1973 & up to me.
DON'T SANDBLAST without first taping up the spindle portion itself. Last edited by Shane; 12-07-2008 at 10:06 PM. |
|
|
|
|
12-08-2008, 12:45 AM
|
#20 | |
|
Commander Taco Bello
Join Date: Sep 2006
Location: Des Moines, Iowa
Posts: 2,232
|
Re: Did I get ripped on these spindles?
Quote:
|
|
|
|
|
|
12-08-2008, 12:53 AM
|
#21 |
|
Phone's ringin Dude.
Join Date: Mar 2007
Location: Colorado Springs
Posts: 1,426
|
Re: Did I get ripped on these spindles?
Those look just like my 2.5' CPP spindles. The had the same markings and no manufacture logo.
__________________
 I pitty the fool with only two headlights!!2003 SILVERADO SS--THE NEW GIRL 1972 GMC--THE OLD GIRL |
|
|
|
|
| Bookmarks |
| Thread Tools | |
| Display Modes | |
|
|
Linear Mode
