|
Register or Log In To remove these advertisements. |
|
|
|
|||||||
 |
|
|
Thread Tools | Display Modes |
02-22-2009, 06:51 PM
|
#1 |
|
Registered User
Join Date: May 2007
Location: Erie pa.
Posts: 57
|
Looking for drive shaft for my 67 4x4
I changed my rear axle to a 14 bolt in my 67 3/4 ton 4x4 and my stock shaft is too long and can't be shortend and balanced because of a dent. I need one 37.5" center to center, is there a correct length crossover in the junk yard that I can look for. Thanks for any help.
__________________
65 tripower conv 4spd gto, 66gto, 67 gto 65 lemans conv 4spd 69 firebird conv. 67 c20 4x4 |
|
|
|
02-22-2009, 07:46 PM
|
#2 |
|
Registered User
Join Date: Sep 2003
Location: Franconia,N.H.
Posts: 1,029
|
Re: Looking for drive shaft for my 67 4x4
if you find a driveshaft that is longer than what you need that is in good shape you can have that cut and balanced. it's a lot easier to have a shop make it the size you need than hunting for a specific driveshaft
__________________
(Only) Member of the CPNE Fan Club  Aint that the truth 67 C-10 350 with 3-speed tranny and 308 gears swb step  82 Z28 Camaro 355 small block over 350 hp and a borg warner super t-10 (blown engine) 72 Chevy K20 Suburban (future project) 70 Chevy K20 now 68 GMC K2500 2003 Chevy 2500hd ccsb 4X4 (daily driver) |
|
|
|
|
02-22-2009, 08:58 PM
|
#3 | |
|
just can't cover up my redneck
Join Date: May 2004
Location: Columbus OH
Posts: 11,414
|
Re: Looking for drive shaft for my 67 4x4
Just because it can't be shortened does not mean that they can't re-tube it. If the ends are good it would still be cheaper than re-working a junkyard unit.
__________________
You can review the site's rules here. Quote:
Bad planning on your part does not necessarily constitute an instant emergency on my part.... The great thing about being a pessimist is that you are either pleasantly surprised or right. 
|
|
|
|
|
|
02-22-2009, 09:35 PM
|
#4 |
|
Registered User
Join Date: May 2007
Location: Erie pa.
Posts: 57
|
Re: Looking for drive shaft for my 67 4x4
I may try that route
__________________
65 tripower conv 4spd gto, 66gto, 67 gto 65 lemans conv 4spd 69 firebird conv. 67 c20 4x4 |
|
|
|
|
02-22-2009, 10:13 PM
|
#5 |
|
the boat guy
Join Date: Jul 2007
Location: springfield mo
Posts: 2,339
|
Re: Looking for drive shaft for my 67 4x4
be sure to take the shop both pieces of the driveshaft if its 2 piece driveshaft, you cant ballance just one piece. dont be suprised if the slip and stub in the center are worn out $$
__________________
67, swb, fleet, tach, throttle, 5.3, 4l60e, 3.73's, fuel cell, 5 lug, p.d.b., 4-6 drop. great little truck 66, stevens drag/ski 18' silouette, 350, 2.02 doublehump heads. comp extreme marine 278 cam, vette 7 fin valve covers, old polished edelbrock intake, velvetdrive, casale v-drive, adj cavitation plate. 28, model a rpu project, |
|
|
|
|
02-23-2009, 06:50 PM
|
#6 |
|
Registered User
Join Date: May 2007
Location: Erie pa.
Posts: 57
|
Re: Looking for drive shaft for my 67 4x4
Getting it retubed , thanks
__________________
65 tripower conv 4spd gto, 66gto, 67 gto 65 lemans conv 4spd 69 firebird conv. 67 c20 4x4 |
|
|
|
|
| Bookmarks |
| Thread Tools | |
| Display Modes | |
|
|
Linear Mode
